French Car Forum

Hello
A tostada newwbie at asking advice on a forum.
I have a 2016 308SW 1.6 HDi which is all well apart from recently coming up with an engine error just after refuelling. Diagnosis of this gave an error with the Eolys pump and or communications with the unit. It had been refilled 5000 miles ago and still had plenty of fluid.
The pump unit has...

Hi there, New member here.
Yesterday I moved my girlfriends Peugeot Partner Tepee out of the parking space to give her better access for her wheelchair. Locked the car, went back inside to finish up nd back out in less than 10 minutes. Unlocked the car, put the key in ignition and it wouldn't turn. Could not start the car at all. I have replaced...

Have error code for tank sensor fault (will look up the code shortly, have it written down)

Cap has two magnets present and correct.

Dug into right rear wheel arch to remove current sensor and check its wiring.

How does the sensor actually unclip from tank inlet?
IMG_20221127_143149640.jpg

Secondly, is there any specific resistance it should...

Hi,

I think I've spiked my ECU!! Can you help to get the car running again, please?

Below is a video of what the car does when turning the key.

There are no blown fuses, as I've checked all the ones under the steering wheel and in a box that's inside the engine.

Kind regards

Jon

Peugeot 306 2001 HDI meridian
Engine Size 1997cc
Cylinders 4...

Hi there I have a low mileage HDI RCZ that has a absolute throttle position of 85.9 % at idle ? And when I try to do live mapping I get no response not even a flat line this is with both Torque app and with my Autel AP200 dongle. The issue that I have with my car is when accelerating through the gears the power drops out and goes into limp mode...

Hello, I am wondering if anyone could help me I have a oil leak on my 5008 vacuum pump and ive been told that replacement is the only option yet I cant seem to understand why the seals cant be replaced on the vacuum pump if the vacuum pump is still in working order.

I have searched the web and cant find a seal kit for my model vacuum pump i have...

greeting guys, need some help here just bought 2012 peugeot 508 1.6 thp 6at aisin transmission, engine light on and scan diagbox found out 2 error code, first one is P0A1A (alternator) but i use meter test idle car is 14volt so mean alternator have charging (totally no idea whats the problem and the second code is U1208 from transmission signal...

Hello every body

I have 308 t9 2016 with a 1.2 i THP 130 purtech petrol engine.

Previously, my engine went to shake really bad making engine turn off by it self two times before, but later this not happen. These days I still get some minor shakes while waiting behind red lights . Later, I notice when engine is on and the car is stop and the...

Discussion Starter · #1 · Nov 21, 2022

Hi all,

Just bought a 2010 Peugeot expert teepee 2.0hdi 120bhp in very good condition but with a slipping clutch.
I found the clutch pedal hard to press and the clutch was slipping so i bought a luk clutch & DMF which was the exact part numbers as the one i removed.
I changed the clutch kit and slave...

Hi All.

I have a 2016 Peugeot 308 Gt line 2.0 with manual 6 spead box.

Clutch fell depressed, its sometimes a bit crunchy into reverse. Not every time but often. If I put it into 2nd then reverse, it's smooth as silk. Also through 1 to 6 when driving normally, it's fine.

Does anyone have any suggestions as to the cause? Is it common? And why...

Can someone tell me what this is? I was driving along and smoke started coming here. As you can see it's obviously leaking but I don't know what it is. It's just to the right of the turbo. IMG_20221122_152821~2.jpg

Good morning campers

Just replaced the head gasket, had the head skimmed, and ground the valves... all working great but there's quite a tappet noise coming from the head. Eases slightly with higher revs but having researched it I think should have put new hydraulic lifters in. I'm not going to strip it all down and do that but in researching I...

How to change heater matrix

Hi All

I’ve got an ongoing issue that looks like its related to the Glow plug relay not getting power, all i get is a constant coil light when the outside temp is below 10c and being a push to start button it won’t allow the engine to turn over, hot wiring the starter makes it run straightaway and once the engine is warm it has no issues and...

Hello friends.

I have now bought my self a very nice Peugeot 307CC 2.0 Sport 177hp 2004 with red/black leather interior :-) Realy nice :-)
This car is ofcourse not perfect ;-)
I have some minor electrical problems.
When i bought the car all the windows/sdoor handle sensors worked fine, but suddenly after i unpluged the battery from the car the...

Hello, want to swap subframe into 207 1.4 petrol verve with available one from 207 1.6 hdi allure. Will be compatible? Look is the same but do not want to experience small difference and then redo the job and it is to remote to measure the hdi one and my without at least a bit of disassembly. Many thanks.
Ps. question is same for tie rods and...

Hi,

I'm about to replace the double front seat in my 2022 Boxer with a single seat. Others who have done this have had trouble with Airbag warning lights because of seat belt pre-tensioners being disconnected. There's a red plug under the seat that I'd like to identify before starting.

I don't have a wiring diagram so can anybody tell me what it...

So today the 206cc had 2 new drop links fitted.

The new are the chrome coloured ones
The black are 17 months old.

Also screen shot of ebay seller best to avoid.

I'm after some help with injectors. The car is running really badly, and there is a loud knocking in time with the engine speed - sounds like its coming from the top end.
I've just plugged in PP and the injector corrections are not in line. After a recent top end strip and rebuild injector 4 was a few percent higher, but now its way out of line....

Hi,

Fluid low warning is coming up. Saw a post on this forum which indicates there is more than one type of eolys fluid depending on car age, as I plan to refill myself and reset with Lexia.

Can someone please help with what fluid I need to buy? Can provide VIN.

Thanks
James

Had an issue with a broken wire to the engine ECU, ran a new power wire to the ECU and got it running again but first drive got an immediate ABS fault. Had the local garage guy put his scanner on it and he was unable to connect to the ABS but could connect to the Engine ECU. This was the direct opposite of the last time he tried (before I replaced...

Hi, my Peugeot 306, just had its MOT, an advisory was the rear wheels are toed into towards the car and will soon be rubbing on the bodywork ! they suggested buying some wheel spacers. I have never heard of them ! where would I source them and what are they called ? thanks in advance Terry.

Hello All,

I think my Old 1.9 expert is terminal. I want to try one last think before I condemn it. I was wonder if any one knows what injector seals and glow plug seals i need for a 2005 expert 1.9d.

Hi

I'm new here because I've just bought my latest French vehicle. It's 2022 Peugeot Boxer which we're going to self convert to a campervan. I've had a look on the Service Box but it appears I now have to pay to get access to the information. I hope it's acceptable to ask this here but is there any way I can get a full spec of my van without...

I have several problems with my new bought project car peugeot 307CC 2004 but for now i want to fix this one.
The problem is that the trunk/boot dose not open with the button on the key or with the push button on the boot, and also not with Autocom computer.
I have searched for power ( 12V ) in the boot but cant find any beside in the 12V outlet....

I sold my 2007 207CC Vti 1.6 auto with 134,000 km on the clock earlier this year to a young student. In my defence I should add that I did everything possible to ensure the engine would be reliable! It had an engine transplant from an XT with 100,000 km on the clock, with new piston rings and valve seals fitted- the cylinder head had a total...

Hi.

I got an P1799 multifunction switch fault (see the pic).
I can't really find info about, but is possible the gear selector sensor?

The fault isn't always there because of being intermediate fault, however the dashboard gives me always: gearbox fault repair needed and my service light is on and not deletable.

Please advise.
Thanks in...

Hello!

I’ve been searching around all over the internet regarding this issue that started for me around two days ago. I couldn’t find something similar.

Model

5008 2010, 1.6HDI FAP

170.000kms / 105.000 miles

issue

When I start the car it starts and run normally, if I then turn off the engine and start it again, the engine won’t crank, I can...

Hi
So I have peugeot 307 year 2002 automatic petrol. It gives me this error automatic gear fault and general code reader gives info oil pressure regulation

Then I changed oil and the two main solenoid valves. Old ones had white connector and new ones had black. And the same error occurs and car goes limp mode.

I read that transmission ecu...

Hi Guys, this ones a headache......

My dash shows KM so tried the normal way via the radio menu to Units and (tut) the only thing listed is temp F - C no miles, no list, just straight into temp setting
Tried BSI reset thinking its got stuck somewhere but to no avail....

This was showing Miles according to the MOT's the guy I got it from said it...

Hi all, I'm welding a friends 2007 Peugeot 107 atm and while mooching around it, I noticed the front of the engine is oily.

Is this something fixable? Reason I ask is I wonder if it is a choked crankcase breather system. I just don't know enough about htis model.

Any heads up would be helpful.

Thanks all.

Doo :)

Hi

I'm having trouble fixing boot of my 2005 307. So far I have changed microswitch, lock and wiring harness. Checked every fuse on the car and done BSI reset multiple times. I measured the new switch and it works as it should. Also tested continuity on all wires in the new harness. Boot light works as it should when manually opening or locking....

Hi folks,

I've got a 2007 207 and I'm replacing the front crankshaft seal... I've replaced many of these over the years but never come up against one so fiddly... no matter what I try the bottom edge always goes in about 1/8 touching the oil pump chain... is there a nack to getting this in straight.. I've even tried using a large socket to drive...

Fault code code P1676 controlled alternator fault

I have read a post here on the french car forum on this fault quite a time back and cannot find it via the search box. I know that member givemeabreak was involved and I cannot remember if the fault was found and fixed. The alternator is charging correctly but I haven't a clue what the fault...

Does anyone know the location of the MAP on this cars engine ?

Hi can anyone confirm the rear lamps on the peugeot 206cc are the same as the 206 excepting the black splash shield which I can pop off. Thanks, as a newbie.

Hello

I am in need of the wiring pin outs for the crank sensor and the cam sensor for the EW10J4S engine.

Vin number VF3**************[VIN obfuscated, can be read by forum staff]

Also could use pin outs for the oil pressure sensor, coolant temp sensor and Intake temp sensor if possible

Thanks

VF3**************[VIN obfuscated, can be read by forum staff]

I am looking for the torque setting for the seat belts. Specifically the top and bottom mounting bolts for the intermediate and rear rows. The bolts have a 16mm head.

Is this something you could help with please.

Thanks.

:(

So, up comes the low coolant warning on the read out checking the coolant bottle its dry, so to get me home it took a litre of the wet stuff. Got home and got a lamp and the underneath of the car was wet , the roads are dry, i then shone my light into the engine bay and the completely bottom of the radiator has a puddle of coolant the full...

Morning all, my 508's gear cable snapped, new ones arrived (without the gear knob) & then eventually the new gear knob arrived. According to Peugeot it's the correct part to match the gear cables & fit the stick & collar.

To select reverse on the car you have to pop it up & to the left, the issue is that the gear knob doesn't fit the collar of...

Hello

I am in need of the wiring diagram for a 2005 206 gti 180, i need the diagram that shows the pinouts for the DBW throttle body and the Pedal.

the car is having an aftermarket ECU installed by myself and I would like to retain the stock pedal and throttle body, however im stuck without the above info.

Hoping for a life line, VIN number -...

Hi Folks

I have a 407SW 2.0HDI sport 2010 Car starts on the button every time, no issues, however it has an intermittent fault. Once started it can drop from its idle revs and stall, it can do this hot or cold, sitting on the driveway or coming up to a set of traffic lights. It so far has always started again with the key on the button, first...

I drive a 3008 .year 2014. I have a message appears that says particle filter additive low.i do not have an ad blue tank on my car.any suggestions on what I need to do.thanks

Hello,

My 308 VIN VF3**************[VIN obfuscated, can be read by forum staff] has just popped up the Depollution system faulty warning in the display screen.

1. If I connect up the PP/diagbox thingy will it give me more information on which part is faulty?

2. I've got a couple of appointments this week that mean the earliest I will be able to have a look at the car is the weekend. Is...

#-o yes its playing up again and the weather isn't good

Heres my notes for the task that i will be sorting as and when
Hope this might help any one else

NS front wire colour blue&white
OS front wire colour green&red

NS rear wire colour green&white
OS rear wire colour red&white

Hello everyone! An error appeared on my car, engine fault need repair. I put the tester on and it shows that the additive pump is no longer communicating with the ECU. I took the additive tank down and noticed that I have about half a tank left. Some time ago this error appeared again but after a few days it disappeared by itself. The car is a...

Hello,

If i would need to replace the transmission cooler (cold engine, overnight), should i expect transmission fluid to flow out or just some drops?

Thx

When either doors are open or closed on this model the windows in the closed position either drop by an inch when door is opened or raise by an inch when the door is closed. This action is to release the class from the roof rubber seal or to re-seat the class into the roof rubber seal. This action has stopped happening on the driver door. I have...

I have a 1990 205 GLD 235K Miles. Owned car since it was 6 months old, regularly serviced. Just started severe vibration when sitting ticking over, changed all engine mounts, N/S driveshaft and crank pulley. No difference at all, engine is running sweet as a nut and starts on the button. Running out of ideas??

this maybe my first post here on FCF so I express my gratitude at it's existance and further thanks to those who skillfully administer it. Apologies for any mistakes to posting protocols ie links or videos

I have a 2017 Boxer van with a VIN VF3**************[VIN obfuscated, can be read by forum staff] currently on around 86k miles with a recommended timing belt change interval of 96k or 10...