French Car Forum

My 2008 207cc 1.6HDi has an odd gear change issue.
Occasionally, when downshifting from 5th to 4th, the gear stick becomes floppy between 5th and reverse, but refuses to move left to the neutral position.
Giving it a 'wiggle', ie back into 5th, or even partially towards reverse seems to unlock this and the spring will now allow the stick to move...

Greetings,

I have a strange coolant leak or something. This only occurs when I drive really really far, like +200km or so without a stop. Last weekend I drove +1100km and when I came home the coolant was below MIN and yet it only needed app half a liter to fill up to MAX.

I have not seen any dribbles or wet spots when I look down the engine...

Hi all,

I'm having an issue which I haven't yet been able to find an answer to in the forum despite searching and reading for some time now.

My apologies in advance for the long winded description:

When I start my car with a cold engine, it has no power. As in, it won't move from standstill without applying throttle and slipping the clutch....

Hello all, I have just purchased a 2020 Expert 1.5. I have a problem with the central locking system. The fob lock button locks all 5 doors, the unlock buttons only unlock the near side sliding door, the 2 front doors and the back door will only unlock using the key in each one, the off side sliding door does not open at all even from inside. On...

Dear all,

I am first time in this Forum and I would like to say Hi to everybody.

I have problem with my Peugeot 3008 1.6Hdi GT 2017 95k km on clock. When I turn on heating on HI on both sides, hot air is going out from driver side vent, but from passenger side is like max 18C degree .
Kindly asking you for any suggestion. Do I have maybe...

Hello. I really need a help with Peugeot 208 piloted (robot) gearbox adaptation. I cannot pass it.
Gearbox is 20CQ97, BVMP.

Full story - i got this car as is, previous owner said that 3rd gear was not shifting well so they replaced the gearbox actuator and it just needs programming . In reality i think many things have been done to it.

Clutch...

Hi

I am looking for a new (or remanufactured) injector for a DW8 WJY engine. I think that the Delphi part number is ldc**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff].

Any one able to help or point in right direction!

Thanks

My ABS light has come on my dashboard and after taking it to the garage they stated the ABS pump needs changing.
This is fine no issues - however I went to order an ABS pump from a second hand seller who asked for my abs pump number. They said I would need to order a new pump with the exact same number on the unit in order for it to work.
When I...

I have a peogeot 508 2019 model. I was leaving for work just before Xmas. Got in the car and it stalled just after pulling out into the road, and wouldn't start again. I called the rac. They tried to start the car. They tried to jump start the car. The car was turning over and wanted to start but it wouldn't have it. They plugged in there...

Hi everyone i have this problem only at winter when it is outside -6,-10 deegres i can't open car from key fob,then no display turns on only on 2nd contact i hear bsi and wipers turn on and cotrol panel switch with lights i don't know what is problem.After few mins cetral lock is 'wake up' and its okay
Here is my yt link to problem 1.4 hdi

Dear forum,
i have a toyota proace which is a peugeot traveller transporter with the 2017 116HP 1.6 engine.
I have got a P242F-00 error with the current mileage of 195.000 km, I think the dpf is not that good but could work for some to thousand km more so that I could repair in summer.
I read the ECU errors with the diagbox 9.68, and tried to...

My 308hdi is showing the above codes after the turbo failed to kick in

Cam Belt Replacement Timing Marks

Had cam belt strip teeth and damage cam. Setting Crank & Cam was easy enough however the Fuel Pump appears to have two holes where timing can be locked - does it matter what one it is locked in.

Hi everyone.
We have a Peugeot SUV 2008 21' engine 1,2L petrol and at 53.000Km the car gave 'Low oil pressure' alarm. The technical representative referred to us that it is a malfunction from the timing belt and perhaps this started to create problem to the engine.
First of all i would like to ask you the followings:
1) Has anybody else face this...

Hello to all.

Our 406 won't rev beyond 1200 rpm.
It's a 2.0 hdi, 110.

Onscreen display is faded, so no message.
Our lexia is out of action at the moment.
Cheap elm227 Bluetooth reader connected to our phone shows no error messages.
Disconnected the MAF, no difference.
Drained some diesel out of the filter housing to do a water test.
Any...

Hello. I have a Peugeot 508 2013 2.0 HDi FAP 140hp. It has the ‘Allure’ trim with Xenon headlights and LED DRL.

For a few weeks I noticed that most of the times I started the car at night, with the headlight switch on AUTO, either the left or right headlight would turn of/off for a few second and then would eventually stay on. Yesterday I got...

Hi! , both rear and front washer (same pump) gave up on my 2008 - 307 1,6HDi LHD , VIN: VF3**************[VIN obfuscated, can be read by forum staff]
All fuses are ok, located pump in right wheelwell , it spins when bypassing pump motor to a battery.
Connected a 5w lightbulb to the motor connector and fired off a long wash, no light.
trying to find connector/pins on the steering wheel...

Our 308 has stalled unexpectedly a couple of times recently. It happens at low revs and is normally preceded by some slightly odd feeling surging. That was pretty gentle though. It started up again after stalling, but required a bit more cranking than normal. Subsequent starts are as normal. No other running issues, and MPG is still solidly at...

Hell all

Blower motor on dads 508 decided to stop working after new year....
B131C 01 errorafter scanning. Cant see any burnt connections. Read about 40 amp fuse....cant find such thing in this car.
I understand that it could also be a motor or resistor....
VIN
VF3**************[VIN obfuscated, can be read by forum staff]

Thanks for any possible help and advise...

hello friend i need some help, i have my 3008 2.0 hdi i have noise from the rear left side there is a hydraulic line with them they are good no knocking noises but only i am hearing like a ring ring ring like a bell ringing on the left side
i started investigating i saw that the rubber its not good my question is can I change only the rubber It...

Hi all, New member here, I have a peugeot 407sw hdi 58 plate with the full satnav screen and climate control, my question is the other day after starting the engine the radio took ages to come on then after it did come on it switched off and I had to reset date and time also I had lost the climate control icons plus some icons from the menu ie...

Hi. Is there a reset sequence for the BSI on a 2008 Boxer 2.2 HDI van?

My Peugeot 207 1.6 VTI 2007 with some issues with Engine Fuse F5.
It look like short-cut in the cranckshaft sensor wiring.
I replaced the oil pressure sensor, cranckshaft sensor but the issue is not solved.

Who can help me is it the:
- ECU
- Wiring
- Engine Fuse box

Were can I find diagrams of the ecu cable connection to check the cranckshaft...

Hello to all.

We are converting our 205 (1.7d) from manual to power steering. We have the rack, the pump, the pipework and reservoir. We are doing an engine and gearbox swap too, so with the engine and box removed, access is excellent.

However, the original shaft from the column to the rack has a square connector with a bolt, whereas the the...

Looking for advice/ info on the above subject as mine has just poured all the coolant into the footwells via the heater vents!!!

I.E. is it do-able or not worth the hassle?
Any tips from anyone that's done it??

Hi guys,
Working on Peugeot 304s cabriolet
1.3 (B02) (75BHP) petrol (XL3S)
Can anyone confirm whether the No1 cylinder is nearest to the clutch end or the timing chain?
Seems to be different from other cars.

I hope this helps if others have a problem with the fan (especially the removal of the fan resistor!)

On a 2013 308 (P7) the heater fan was not working. Having looked at other posts about heater blowers for the C4 (C4 heater/air con not working) on this forum it seems to be a similar system to the Citroen. Note that this 308 is a dual zone...

Hello Team!
Im oner of one peugeot 508 sw 2011 model.
The blower fan motor do not work on car.
I have bought car with this problem.
Im mekanik and electrician guy, and i work for big company - so i know how to work on vehicle.
Please can sombady of team help me with one electric schematic diagram for blower fan motor and one work procedur how to...

Hi All Happy New Year!
I had commandeered a previous thread but still
Need advice for replacement method for these please.

I am collecting today. Ordered a pair so I can swap both.

IMG_9985.jpeg
Faulty NSR axle bump stop (rubber missing)

IMG_9984.jpeg
Good OSR axle bump stop

IMG_0158.jpeg
Replacement pair

Thanks in advance

Hi all, hoping someone can point me in some direction here!

Vehicle is a 2.2 Boxer, 2015.

SO this all started when trying to align a new airbag ECU to my BSI. When connecting DiagBox to my vehicle, I get communication errors to every module apart from the BSI, ABS and ECM. Looking at the BSI parameter live data, I can see that all modules are...

Hi,
I have problem with my 308 sw 1.6 hdi 120 from 2017, 60k on the clock. While driving, when I press the gas pedal, there is a fast rattling sound, when I release it it disappears immediately, the rattling noise can be heard in all gears, but especially on the highest ones. The noise will only appear while driving, engine runs smoothly, no...

Hi guys got a 508 rxh estate in.
Seems it's had 2 new keys as the 2 keys i have don't have the emergency entry keys
But I have a separate bump key that must have been cut
Both keys will start the car but won't lock or unlock
If you don't have the key in the reader it states key not detected also does this if you open a door.

Had a locksmith out...

Hi thanks for the add, I have rebuilt a 18 plate boxer dw 2.0 hdi addbluen engine that had been in water ceased belt tensioner dropped belt rebuilt head one new rod

all is good apart fro p00bc21 and po2ed21 air circuit air flow higher than theoretical air flow after sales threshold other code is lower than...

Smoke tested air side new egr took...

Hi

I have a Peugeot expert DW8 engine 54 plate that has issues when I start it up. It has been laid up for 4 months.
1. It struggles to start when cold
2. When it starts there is loads of white smoke (enough to leave a ring on the ground) and with misfiring.
3. If turn it off and restart it sounds like all I can describe it as is a man with a...

When I start my car, no problem but it does get to 90c on the coolant gauge quite quickly and after a while the whole car starts shuddering quite violently, I mostly have to pull over because of this, I have to let it to cool down otherwise it will just keep shuddering, also my cars fan does not turn on it’s just off at 90c.

(I suspect it’s...

My son's 208 suddenly ran rough, no power and idle was very rough. The EML was on, and diagbox pulled a P1339 code. On a restart it would rev, so not in limp mode straight away, but no real power. Rad fan ran on at high after engine switch off. Interestingly. it would start with any coil disconnected, but ran even worse, no matter which cylinder...

I have a Peugeot RCZ 2.0 HDi 163 which up until recently has been amazing.

We are querying head gasket or EGR cooler?

Bit of background:
Car does not over heat, does not produce white smoke, does not loose coolant.
Car looses cabin heat on idle

The only loss of coolant is via the expansion tank when this pressurises too much. This coolant is...

fault code says low pressure fuel pump fault. changed the pump twice one lower half and then the upper half put the fault stays active

Hi , does someone else have experienced display suddenly going dark?

It happened yesterday, then it was back on and now it doesn't turn on at all, whick is quite annoying.

I assume that the power goes to the display since the orange wrench is glowing on a startup and then disappearing when engine is running.

Need help. Engine computer does not communicate. there is a fault code U1208 in ABS/ESP ..... Engine speed enters emergency mode 1500 RPM. Engine & ABS/ESP & STOP warning lights are on...... i can't find SERVICE MANUAL for Peugeot 206+ anywhere. with ECM VALEO V34.3

I currently have a fault with obd code of c1392

It has a host of lights abs, traction, hill start , spanner all in Orange

The vac pump was screaming and has been replaced along with 4 abs sensors

C1392 is calibration according to what I can sense

I’ve checked the volts on all 4 leads and are reading constant and correct

Any thoughts and how...

Yesterday had the STOP lamp illuminate alongside a message telling me there is a Brake system fault.

The Following codes were pulled using a MaxiCOM MK808BT

U1213 81 - Fault in communication with ABS or ESP ECU Communication Invalid
C1358 - Fault in electro valves supply
U1213 - No communication with ESP ECU Incorrect Value Recieved
U1802 87 -...

Hi I have a flip screen sat nav in my 308 and the screen started breaking up so I did a repair on the cable on testing I have shorted something and screen stopped working even the motor I have managed to source another screen and cable but it now flips up but nothing else the radio works fine and Bluetooth is ok I hope someone can help are they...

hi, I have a 2013 308 Diesel (1.6L)

went in to limp mode a week ago.
local garage has advised me that the DPF needs to be replaced - £400
they did also offer to drill it out and remap the ECU for £250 - appears this may be illegal, and would almost certainly invalidate my insurance even if not illegal

since gone to National Tyres Autocare, they...

Matt ive lost the diagrames for the headlamp wire colours to what light for my 308cc can you pop them up here please im needed to know which wire feed what lamp on the front.

I need to change the injectors on my 1999 Peugeot 206 1.4i but cannot figure out the correct part number. Engine code is KFX 1000030960.jpg

Hello everyone,I want to replace this plastic pipe because it is leaking on connection with turbo.Problem is that I can not find short pipe like on my car(peugeot 307 110hp 2006).Is there any way to seal pipe that I already have,or can I buy that long one and cut it.Does anybody know why there is short and long versions..Thank you in advance.

Hello everyone,

I recently bought a Peugeot Partner 2019 1.6 BlueHDi with only 20,000 km on it. I’ve noticed that black smoke comes from the exhaust, especially when I accelerate. The car seems to run fine otherwise, but this issue concerns me.

Could anyone help me understand what might be causing this? Is it a common issue with this engine, and...

Hi again please can some one help, i am looking for a Peugeot partner 2002 wiring diagram

Hey all! I need some advice with my expert that what could be wrong.

While driving under 2100 rpm there is some jerking while The engine is on low load. It's most noticiable when driving around 90km/H with 5 or 6th Gear and trying to maintain steady highway speed. When i accelerate the van There is no jerking. The jerking feels like that the...