French Car Forum

Had wing mirror broken (case ) only will Citroen parts fit or a used complete unit mine is powerfold
Brian

Hello,

Would anyone have a wiring diagram from the brake pedal to the brake lights at rear?

I believe my two errors could be related and something along the wiring route is playing up.

My rear windscreen brake light is working and bulbs right and left are ok.

Even though the rear windscreen brake light was working I changed the brake light...

Please would you ID the engine type fitted to this car.

VF3**************[VIN obfuscated, can be read by forum staff]

It is a 2007 207S 1.4 petrol.

Many thanks

Hi Guys
My Partner Teepee 1.6 HDI - circa 2015 reg with 71k on the clock has started to play up, with the radio playing OK then
switching off on its own accord. IT then restarts after about 2 minutes (Pug logo showing) and carries on playing then repeats the switch off
again 5 mns later. It could be on FM or DAB or trip screen - no difference....

Hi,

I have a BSI fault and I have located a replacement BSI with the exact same BOOT, HARD and Variant/Version numbers.

I have a 2.0 407 HDi and this replacement is from a Citroen C5 1.6 HDi.

As all software/firmware and unit model numbers are the same, is it only the eeprom chip that needs swapped?

Regards

Barry

Hi i would like to ask if there is eneyone that can give me some addvice . I brought a can that used to be owned by my mother-in-law . When she had the car it was always taken back to the dealers to have eney work undertaken . She past away a out 5 years ago and her then partner sold the car on to his nethew. Who basicly just ran the car a d spent...

Hi I have a 1999 Peugeot expert was leaving diesel from the back nearest the engine block from between the back housing were the pipes are an the cast pump part question is how do you get the steel bit we're the pipes connect to off

Hello to all

I really need some advice please.

My wife has a Peugeot 308cc 2013 model. When the drivers door is opened the window drops a few mm. The window is supposed to stay down untill the door is closed. However it is going back up before and casuing the window to be on the outside of the rubber seal. Ive checked the passenger side and it...

My daughter's having an intermittent problem again with her car - very similar to problems she had a year ago.

Faltering then cutting out at idle, depollution warning and EML on.

Diagbox codes:
01.jpg
02.jpg
03.jpg
04.jpg
05.jpg

Clear the faults and it's OK for a while, then the issue returns.

I replaced the crankshaft position...

Maybe there is a topic but I can`t find it :(.
I have good old 405 1.9td with perfect enegine and gearbox(no immobiliser), but the body is killed by the rust. I want to put the engine in 206 1.9d with A/C. I am warried about the electric system. Maybe I have to make some mods? and what about the drive shaft. Do thay fit on 405`s gearbox?

Hello all,

I have recently purchased a 2015 (65 plate) Bipper 1.3HDi. It has covered a mere 138k but has issues.

Since purchase I have replaced:
Diesel leak off pipes
Removed/had tested/refitted 4 injectors
Battery
Blanked EGR with holed blank plate

The problem with it is that it starts perfectly well with no issues, will sit and tick over...

Good morning all,I recently had a front driver's side coil spring replaced at my local garage but now when I drive I hear a rather loud knocking noise coming from which seems like driver's side,I am a bit concerned that it could be either track rod end or ball joint,I am at a loss to why it's doing this,my question is would it still be safe to...

I have a Peugeot bipper with a fuel problem I have fuel coming for filter to hp pump have replaced pump ran for a hour then stopped again and got another pump and would not go again it's a new solenoid and there is power to it but does not open when ignition is turned on no immobiliser faults had key reprogramed only fault on van is po68a ECM/PCM...

Hi Folks, had a look online and on here but can't find exactly my situation described so posting the details..

I believe my clutch cable has snapped. Car was stationary on my driveway at home (fortunately) started up, clutch pedal down to get into 1st but instead there was a bit of a bang and the pedal dropped to the floor and wouldn't return....

Hello everyone,
Peugeot is a famous automaker. SUVs are often preferred by customers and they are also favored by many users. The most famous SUVs of the company can be mentioned: 3008, 5008, ... I am in need of buying a car and want to buy a 3008. I want to ask everyone to advise whether to buy that car or not. are not? Is it worth the money I...

Hi everyone, first post here but looking for some help with the 1.9 XUD9(TE) I Believe.
I have a Lucas diesel pump but looking to upgrade to a Bosch. It seems these pumps are pretty hard to come by now. I've managed to find one but it states it for a 1998 406 1.9 D Turbo
Would that pump fit on my engine? And would anyone have a photo of the Bosch...

Hi, I am having issues with my car and i think i found the problem. It is difficult to start when the engine is cold, greyish / black exhaust fumes and sluggish at times. I feel car hesitating too from 1300rpm to 2000 rpm. I blanked the EGR and still I am having problems. I bet its the Injectors as I have spoken to several mechanics about this...

Hi all.
My drivers door mirror folds back on command,and automatically when doors are locked.
The Nearside mirror also folded until 18 months ago,when it ceased to operate.
Now there is No sound,but it can be folded manually.
Any thoughts ? :?:

Hi,today I got those error codes,car pulls good,engine sounds good.No change..What could be a problem?Tnx in advance

I purchased a 2015 Partner with 58,000 and full history. It’s an automatic. I have a plan to turn it into a micro camper.

I was given two options by the dealer:- A ‘warranty included’ sale, or a ‘trade sale’ with no warranty for £300 less. My budget dictated the latter.

As soon as I drove it off the lot, I thought ‘wow that’s not very smooth’....

Hi we’ve had pollution system faulty error come up on our car. We had the turbo cleaned then replaced but again when driving on the motorway it has reappeared- we can’t get above 3000revs and it loses speed uphill- basically it has lost power and won’t go above 70 mph. Any suggestions as to what this might be?

Hi
What is the torque socket size for rear brake caliper carrier bolts please? Also where can i get some new bolts from?
07 Peugeot expert mk3.

Hi all!

I have followed your forum for a long time and always found solid info on my issuses with my 308 SV (2014), but this time I can't find any discussions on the subject. Here's my dilemma.

After reassemble i can not turn the key in the barrel. Electronics all work like before.

I have had a squeeking steering column for a while and wanted...

Hi,

I recently owned car with boost problem.
When i drive few minutes on some rpm's, like 2000rpm, i totally loose boost from turbo.
On higher rpm's i think that it can't happen.

After i restart car everything is normal, and again when i drive normally i loose boost in minute, if i drive with pedal to metal i have boost all time, with some...

Hi everyone,I’ve got a 206gti 2001,I’ve had to disconnect the battery so the blaupunkt 2040 requires the code but my multifunction display isn’t working(changed the 4 bulbs and had a look at the soldering but I can’t get it up and running,you can sometimes see the display in certain light,can not get hold of a 4 bulb display for love nor...

wont start sometimes. will run on either sometimes but then dies. wont start from bump start. motor spins at decent speed when cranking. glow plug code comes up. I installed new fuel filter to no avail. Have not tried leak check at injectors, have not done anything with fuel sensor. Vin is VF3**************[VIN obfuscated, can be read by forum staff]

Dear, All

I have a Peugeot 308 1.6 turbo 2009, my vin number is VF3**************[VIN obfuscated, can be read by forum staff]

I have been having hesitation on light pedal acceleration under 2k rpm and going downhill I get a feels like a misfire. Onload and with aircon on it is worse, but once warm it feels less but I can feel a bit of a misfire/hesitation while driving still.

This all...

OK I know there is a lot of cruise control posts.

let me set you up..
2007 207 1.4 16v kfu engine. So it's pre vti and has cam belt. the last year this engine was offered before the vti replaced it..
its an 89bhp se premium spec. that is auto lights.. auto wipers.. auto dimming rear view mirror. velour seats with front arm rests. Full light check...

Having had this code P0382 arrive on my ecu and not finding much to help me out I am now trying to help anyone else that may be experiencing the same problem. It seems that our 206 has a failsafe on the event of the heat plugs failing and puts it into limp mode , scratching head and trying to diagnose the problem . I dicided to find an old heat...

Want to put my motor in a van it's a 06 407 dw10bted4. And what issues are there with remapping thanks.

Any recommendations for spark plugs for the EW12 engine? Anyone tried gapping single electrode spark plug further apart? Multi-electrode spark plugs? Or a one hotter heat range / transfer plug? Thanks.

Hi all

My 407 has the dreaded cold one side problem (drivers side) I have changed the flap motor and still no luck. The flaps work fine and the shaft is not broken. When I connected the new motor and adjust the temperature it does not move at all. Even before it’s bolted back on. I presume electrical fault?

The Haynes manual shows temp sensors...

Hi
I've just fitted a saxo 1.5 engine to my Peugeot 106. It came with a Bosch pump as did my original engine. It will not start. No fuel at injectors.
I've concluded the new engine injection pump is imobilised!???
I'm going to re fit the original pump.
Am I correct in my assumption that the injection pump on the new engine is locked /...

Hello all,

My AC is not working, I have had car at 2 different mechanics who ran dye/pressure check and both said the evaporator had a leak. Maybe both were wrong.

However, they both have said they can not find an evaporator from any supplier and both said its a dash out job.
My 3 questions are:

1) Is there another easier way to remove and...

i have a 308 sw sport hdi 1.6 diesel ,clutch needs replaceing as it as started to slip ,been told the car as a dmf
so wanted to know will i need a clutch plate that is solid or with springs ,as i was told that a solid one is right as the dmf will do the work on the spring side ,
i have had a luk repset pro 3 piece kit witch as the solid clutch...

Hi all. Help needed please. Boxer 2017 2.0ltr. Having an issue with temp sensor shooting up to full scale, only for about a second which then stops the engine, happens mostly when cold but also when hot, sometimes comes up with a message radiator temperature high and sometimes stop safely. Took to main dealer for diagnostic check, told pipe come...

Im changing the radiator on the Boxer III.
But cannot for the world understand how to loosen the plastic connetor on the radioator - never seen this type.
Do I need to open on one side?
Pressing them in, doesnt help.
Radiator hose clamp.jpg

Hi, can anybody help please?! I have a Peugeot 2008 diesel on a 16 plate and have a problem with the steering. It pulls to the right until about 30 miles per hour, this is upon acceleration and when slowing down. Above 30 mph it drives straight. I have had the tyre pressure and tracking checked, it has been up on a ramp and the suspension and...

Hello from Sweden

Our friends work car started to run on 3 cylinders and was producing a lot of smoke.
Fault code on cylinder 3, missfire.
BUT.
What cylinder is 1?
And Id be very thankfull if someome could tell me what ECU it has and what type of injectors.
VIN:
VF3**************[VIN obfuscated, can be read by forum staff]

I have SnapOn and Autocom. Do not have Peugeot specific OBD - only...

I am considering buying 508 with 1.6 Blue HDI engine. Year 2016, around 50 k miles, serviced regularly. There are horror stories about injector, cambelt and turbo all over internet. I wonder if I should pass, or go for it, as car looks good and according to internet, drives really well. I would appreciate more reading on the topic.
So far I found...

Hi
I tried to slove this problem for a while now, with no success in either finding solution online or fixing it myself.
I bought this car with 250k km on the clock
It now has 260k km
I serviced the car when I bought it at 250k (all filters + Total oil) and now recently at 260k (air filter, oil filter, cabin filter + Total oil)
So here is where my...

I have got a 2007 Peugeot 207 SW and some low life has smashed my driver side rear door window, i have went to a scrap yard today and found a 2013 207 SW and the man is willing to give me the back window for cheaper than anything on the internet but i was just wondering before i buy it do the window sizes differ in size from the 2007 model to the...

Hi, as the title suggest, can anyone let me know how to remove the rear spring out of the electrically controlled damper? Please see photo. Thanks.

Hi,

I am wondering if any one have replaced the 407's rear hub bearing only: What I mean is pressing the old bearing out of the wheel flange and mounting a new one in. It seems that Peugeot have only the flange, bearing, nut, and cover as an assembly to sell to the public. I believe the bearing assembly is made by SNR. If anyone have only pressed...

I've been forced to take the gearbox off, due to a slipping clutch (new clutch fitted less than a year ago). Exterior of the bell housing is wet with oil so looks like a seal has gone. The preparation is all done, and what a job that was! Everything is sitting on jacks at the moment. I am looking for a bolting diagram for the bell-house to engine...

Hi! Got this message on my dashboard . My van has done about 72,000 miles but still under warranty. Booked with the dealer on 1/3/2021. Is this serious problem? Can I use my van for 2 weeks or will it lead to more serious problems?. Its Peugeot Expert 1.6 Blue Hdi 115HP, 2018 year.
Thanks in advance.

I just bought a 2007 Peugeot 407 1.6 HDi with 160.000km as my first car. I love how the car looks, how it drives and how comfortable it is and so I´d like to keep it running well. It has a couple of problems and I wanted to ask if any of them need urgent care.

1. EGR Valve stuck open, code P1462 (I took it to a mechanic before buying it and he...

G'evening all

In the days when I had a series of Citroens I frequented this site a lot and then I went to the dark side, Toyota and Lexus Hybrids, my tools have grown rusty and scattered and the brain equally atrophied, Now I have discovered the Peugeot 508 SW RXH I wonder if before I do something silly does anybody have experience of these? what...

Hi does anyone know where the cooling fan relay is located on a Peugeot 5008 2010 please

Hey guys thank you for welcoming me here. My pug 307 1.6v 2007 auto has now reached 106k miles and Ive had the fluid changed, what was put in was Dexron 6 (I know the recommended is Esso or Mobil LT71141). But I have found contrasting threads on here. Some have tried Dexron 3 before and it lasted. Just want to ask, anyone had any experience with...