French Car Forum

Hi, I know this is a long shot but here it goes...
My car suddenly started to develop this issue where if I pull from low RPMs I get a cut off the throttle for a second then it goes back to normal, battery and engine lights come on but after a few seconds it disappears if I drive calmly.
If I continue to acelerate full throtle going through the...

Hello! I'm having some trouble raising boost pressure on my -95 605. I've had the engine out completely and checked most everything such as timing and exhaust seals. The turbo turbine housing was cracked in three pieces so I replaced the whole turbo in the hopes that this would give me more pressure. Unfortunately this didn't yield me much results...

Hi guys,

I want to change the oil at my EAT6. I went to the servicebox, typed my VIN, and the only thing written regarding oil is JWS 3324 specification.

I asked the dealer for the price, and I was shocked, they told me 130€ for 2 liters.

I went to the other local auto-part stores, and told them about JWS 3324 specification, and the price was...

Hi all,

I have a Peugeot 3008 GT PREMIUM 2019.

Every day I start the car for a good 2-3 minutes before driving it.

This week the heater stopped blowing hot air.

The fun fact is, when I switch the car off for around 5 minutes and switch it on again, the hot air is back working.

Any one could shed some light of what is happening and a possible...

Witam. Mam problem z aktualizacj? to map. Posiadam peugeot 508 2018 GT First edition i aplikacja my peugeot informuje o aktualizacji. Po pobraniu i zgraniu na pendrive w radiu jest informacja i? wersja niezgodna ze sprz?tem. Czy mia? kto? taki problem ?

Translation:
Hello, I have a problem with the update to maps. I have a peugeot 508 2018 GT...

I've did a wee search but information available seems to be individual rather than Inclusive.

Looking for build info, mechanical parts for the rolling chassis, wheel bearings, drop links, ball joints etc etc.
I'm also looking for (apologies in advance) Gearbox information. Not sure if this is relevant but the gearbox housing has OHA U3 cast into...

Peugeot 308(t9) 1.6bluehdi P00BC error
Replaced Maf and Map sensors and still the same. Error pop up when driving and releasing accelerator pedal while its in gear. ?t mean when engine in compressor (I dont know is it correctly in English words) Turbo hoses looks good not any leak, also intercooler doesnt leak. Does anyone have any ideas of what...

Hi got this popping up on my 208 gti, air con seems fine and compressor is engaging, any suggestions? Getting the pressure tested later but just want to see if anyone may have any ideas?

Hello,
my 2010 Peugeot Boxer 2.2 HDI has a very frustrating ECU/BSI related issue. The ECU has a P1310 Inertia switch permanent programming not done fault code for the ECU. This does not appear to relate to the actual inertia switch fuel cut-off which works as expected. I am wondering if this fault code relates to a crank, start but no run issue?...

Hello,

The wife went to use the car this morning, and found the passenger wing mirror failed to open when she unlocked the car.
Looking at it, the mirror is locked in the closed position. I've tried opening it with the drivers controls but no luck.

The mirror within the housing cant be adjusted, and the auto adjust in reverse doesn't seem to...

Hello we are after a replacement used engine for our Peugeot partner engine code BHZ is it possible to use ( other same type engine with similar codes )

There looks to be a difference as ours has add blue , but what difference does that make in compatibility ? Thanks Phil (North Wales)

207cc Temp gauge is not working,So I changed the sender unit but still not working, But if you remove the Connector the Gauge
shoots up to Max and Fan starts running, Any ideas ?

Peugeot 5008 2010. The wipers activate ok but the washer pump has stopped running. I haven’t found any failed fuses. The user manual says F15 10A is washer/wiper, but when I pull that fuse the wipers still operate when washer/wiper stalk is activated.
Thank you in advance for any tips or suggestions.

Good Afternoon and thanks in advanced for the help

I was driving my 2012 3008 1.6 HDI last week when the engine cut out and would not restart. At first I suspected the timing belt however this looks in tact. I do believe the water pump may have failed as the coolant tank is empty.

I have turned the car over and the belt looks fine, could the...

Hi guys, currently have a 15 plate Ds5 1.6 e-hdi auto with the etg6 gearbox. While I've always loved the shape and design of the car, kind of wish I went for the 2 litre version for the extra power. The DS is a heavy car, so it's slow and the etg6 gearbox stutters around sometimes.

My question is I'm about to pull the trigger on a 65 plate 308 GT...

Hi all

The gearbox input shaft bearing has gone on our 207 (1.4 8V 2008) and it is certainly making its presence known!

My first choice would be to get a 2nd hand gearbox but I need the gearbox code. In some other posts I have read that there used to be a way of finding this our from the registration number. Does anyone still have the ability to...

is it possible to convert the automatic adjustable one to a manual one?

Hi, again..
I thought i've done with ad blue nonsense at the moment, but not. Returning today at the highway, after 180 km trip, engine fault came up and urea fault after a while preventing starting after 1100 km. Car was driving excellent, no other signs that something was really wrong. The only that i did before fault come up, was to energize...

I have a 508GT SW from 2014.
It seems like the climate control always blows air on the windscreen, regardless of what settings I choose on the dials.

The two settings for the feet and vents towards the passengers seems to turn on and off as intended. This is annoying, since the automatic settings doesn't get enough heat to the feet or body, most...

Hallo sorry to ask, i know topic says c4.
I have a peugeot 5008 from 2017 new model. Same problem only heat on the drive side, its at LHD car..
When switcing to cold i the air flow is the same on both went i center dashboard, but with hot its most the left side.
Do eny 1 have a picture of the air vent flaps and so on.
I dont know if my issue is...

Shout out to anyone with a 308cc , the joint at the driver window has developed a slow drip , whats the best way to fix or cure this ...... 🤔

Im looking into buying a used Peugeot 3008 hybrid4 with an 2 error codes. No engine light but warning when trying electric only mode. I just want to know the severity of theses. The Price on the car is good.

Vin: VF3**************[VIN obfuscated, can be read by forum staff]

Error codes
1059
16AB

Thanx in advance

Hello all,

First post here for many years, I did have a Saxo VTR which was a brilliant little thing and I always got great advice on the forum so thought I would ask again.

I now have a 308 GT Line SW with the 2.0l e-HDI motor.

Loving it so far except for the constant U1218 Communication Fault with built-in systems interface error code that I...

Thanx very much Marc, Looks like I will go for recon

Steve

Hi All
recently purchased a peugeot 307 5 door the central locking is not working at all i can unlock / lock drivers door with key boot sometimes opens both rear doors and front passenger door remain locked and cannot open from inside or outside tried taking deadlocking off on bsi through pp2000 and diagabox but still the same any advice on where...

I have a 2004 Peugeot 206 1.4. I bought this oil.

It's formulated for fuel economy, low SAPS. Reading a bit more I think it's meant for a more modern direct injection engine.

I'm wondering is it the wrong stuff? What would be the recommended oii?

Hi all, have a 2012 Peugeot 508 that came in with fault code p1755 clutch jammed, diagnosed as the release bearing leaking. Replaced it with a 3 piece LUK kit (flywheel seems perfect) and went about the programming process using diagbox and kept cancelling at the clutch biting point stage. Checked live data and clutch travel wasn't changing with...

Hello
I have Grandland X, 2020. As it is known same structure with 3008.
I want to retrofit keyless entry/start, but didn't find wiring diagram.
Is there anyone who can share?
Regards

Hi All

I have a 2009 207cc that I bought knowing there was a roof fault. I've been reading through a few threads on here and other forums which have been pretty helpful.

I've used Diagbox to narrow the issue down
Code is C882 - Roof boot open switch - Open circuit
Confirmed on live data that Roof box open switch shows as faulty. The info box...

Ever since our local garage changed the ventilator fan for the interior, we have been facing issues with the airco on the driver's side. So far, two Peugeot garages and two general garages are unable to fix the problem.

Our car is a Peugeot 508 Féline from 2016 (VIN: VF3**************[VIN obfuscated, can be read by forum staff]), with a quadruple airconditioning system. The valves seem to...

Good morning. Thinking of buying a used 3008 either 1.6 or 2.0 HDi engine.

Can anyone tell me the timing belt schedules please as I find different info!

Thanks all.

Chris

I have a genuine MAF which I purchased some time ago but never fitted, the car has had poor acceleration for some time so I'm thinking I might as well replace the current aftermarket MAF (fitted by a reputable diesel specialist...and fitting it fixed the EML anti pollution fault) with the genuine one I have but I can't remember if the auto...

Hi all , I have had a few lights come up on my dash of my 3008 ,2013, 1.6 HDi , 1560 84 kw 114 bhp 9HD (DV6CTED) , the scan gives code:: U1208 fault in communication with the engine management ecu or with the drive train interface ecu invalid data.

I am going to check the connectors on the ESP ecu but can't seem to find out where it is , could...

Hello all,

I’m having issues trying to change the radio wave band to AM or DAB but the options to change are greyed out for change waveband and under the options the choices I have is TA, RDS not AM or DAB. I believe I have the RNEG2.86.B model as this what the information states on the display.

I have a 3008 Hybrid 4 model.

Any help will be...

Hi,

The side door on my boxer is dripping from the top seal when it rains. Mostly near the front but also a little in the middle. The seal itself looks to be in good condition, its only a 2022.
The door closes very easily, compared to my previous 2016 Relay van where you had to give it a real whack! I'm wondering if it needs to be tighter...

Hi
I've been crackers enough to buy a second hand proace which I now realise has peugeot guts. last owners weren't aware that needed DFP fluid additive so the pump has burnt out and I've had fault codes and diagnostics have sourced issue to the pump and tank

I'm trying to source a new one, struggling to find the product number

I've found a...

DTC P0192 Fuel pressure sensor 1 circuit low
Was the original DTC which replacing with Bosch 0281002919 which is the same part number as the old. OEM part number is 1920.LJ

On plugging the new sensor in, I got a new a DTC code. The packaging appear genuine Bosch, was unopened, and I have another new sensor coming.

The new DTC, DTC P2685 Supply...

Hi,

I'm facing some problems with my Peugeot 207 1.6HDI, 2009, 90HP, 9HX motor.
First of all - engine sometimes cuts off with a antipollution faulty message followed by low oil pressure message. Sometimes antipollution faulty appears after turning ingition on and the car won't start. Second try usually helps. All the filters were changed to new...

I purchased a 207 GTI, where someone has tried to fit 208 seatbelt pretensioners and steering wheel into the 207. I swapped out the 208 seatlbelt pretensioners for 207 ones to make sure this wasn't the issue. I then swapped back in the 207 steering wheel and airbag. The fault code is listed drivers side/passenger side pretentioner serious fault -...

Hi,
Problem with the driver's door lock, the car does not detect whether the door is open or not.
I got error B173A 00

The lock has already been replaced because the previous one did not lock the door

Hi, does anyone know why my 2019 Peugeot boxer 2.0. injectors won't fire. I get the correct pressure at fuel rail and have tried new injectors. I also don't have any faults show up on diagnostic scanner.

Thanks

My 2008 207cc 1.6HDi has an odd gear change issue.
Occasionally, when downshifting from 5th to 4th, the gear stick becomes floppy between 5th and reverse, but refuses to move left to the neutral position.
Giving it a 'wiggle', ie back into 5th, or even partially towards reverse seems to unlock this and the spring will now allow the stick to move...

Greetings,

I have a strange coolant leak or something. This only occurs when I drive really really far, like +200km or so without a stop. Last weekend I drove +1100km and when I came home the coolant was below MIN and yet it only needed app half a liter to fill up to MAX.

I have not seen any dribbles or wet spots when I look down the engine...

Hi all,

I'm having an issue which I haven't yet been able to find an answer to in the forum despite searching and reading for some time now.

My apologies in advance for the long winded description:

When I start my car with a cold engine, it has no power. As in, it won't move from standstill without applying throttle and slipping the clutch....

Hello all, I have just purchased a 2020 Expert 1.5. I have a problem with the central locking system. The fob lock button locks all 5 doors, the unlock buttons only unlock the near side sliding door, the 2 front doors and the back door will only unlock using the key in each one, the off side sliding door does not open at all even from inside. On...

Dear all,

I am first time in this Forum and I would like to say Hi to everybody.

I have problem with my Peugeot 3008 1.6Hdi GT 2017 95k km on clock. When I turn on heating on HI on both sides, hot air is going out from driver side vent, but from passenger side is like max 18C degree .
Kindly asking you for any suggestion. Do I have maybe...

Hello. I really need a help with Peugeot 208 piloted (robot) gearbox adaptation. I cannot pass it.
Gearbox is 20CQ97, BVMP.

Full story - i got this car as is, previous owner said that 3rd gear was not shifting well so they replaced the gearbox actuator and it just needs programming . In reality i think many things have been done to it.

Clutch...

Hi

I am looking for a new (or remanufactured) injector for a DW8 WJY engine. I think that the Delphi part number is ldc**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff].

Any one able to help or point in right direction!

Thanks

My ABS light has come on my dashboard and after taking it to the garage they stated the ABS pump needs changing.
This is fine no issues - however I went to order an ABS pump from a second hand seller who asked for my abs pump number. They said I would need to order a new pump with the exact same number on the unit in order for it to work.
When I...

I have a peogeot 508 2019 model. I was leaving for work just before Xmas. Got in the car and it stalled just after pulling out into the road, and wouldn't start again. I called the rac. They tried to start the car. They tried to jump start the car. The car was turning over and wanted to start but it wouldn't have it. They plugged in there...