French Car Forum

Hello everyone. I am looking for some help regarding my Adblue system issues. The vehicle I am trying to fix is Peugeot Boxer Mk3 2019 2.0 day van.
Main issue: Check AdBlue system message on dash and check engine light on. No count down. Scanned with Snapon reader and it comes up with:
Engine:
P20E8-21 Pressure of the urea fluid too low
u1118-87...

Good morning everyone, my Jumpy II, with 85,000 km, started giving me the error of possible clogging of the DPF filter in the summer. After about 1000km of long journeys the light went off. After a few months, the warning light came on again on most busy city routes. I would like to get an economical lexia3 interface to force the cleaning of the...

i have a 2019 1.6hdi berlingo van was just wondering if the egr valve is taking gasses before or after the dpf and adblue injector?

thanks john

ABS and ESP lights on and the multi display shows fault with the ABS system but Diagbox nothing wrong don't know what to do
have changed the ABS sensor unexpected front , and changed the nut to the right sensor (front) but the Diagbox shows that there is nothing wrong and this does not go through inspection with light lights on the dashboard what...

Hello!.
I have an other question.
Again it's about the P 407 v6 petrol with vin: VF3**************[VIN obfuscated, can be read by forum staff]
The bluetooth does not work. The previous owner (my sister) of the car said that from one day to the next it stopped working.
The diagBox shows the following list of errors regarding bluetooth.

BSI code F03d
Defect absence of communication with the...

Hi Folks-

I've just joined the forum in the hope that someone can point me in the right direction for an attempt at a DIY diagnosis for my car. I've got the Haynes manual and have started following the steps to attempt to diagnose, but I'm a complete novice in this department having only completed some basic repairs (header tank and fuel filler...

Just popped up in an email.

My Citroën C4 Picasso 2,0 diesel, euro 5, 2011, has a problem. It's turbocharger overboost al the time. Engine doesn't get faults from it, but live parameters shows different story. Turbo fails to stop in time, it stops only with loud hissing noise, to drop excessive boost. I have changed all vacuum system hoses, solenoids (the one that regulates...

Hi all I've got a peugoet boxer 2010 2.2 which has the engine management light on with the code p1304 after attempts by 2 garages and the AA to put the light out it comes straight back on I was told it's because there is too much fuel going in and the pressure is high on the fuel rail also that they can't comunicate with the engine management on...

Hi. I recently purchased this van and have always had difficulties with starting. Initially assumed it was due to not being serviced/run for a while. Work was planned to change glow plugs to see if this was the issue, when the mechanic got in there they noticed that one of the plugs was removed and a bolt was inserted. This was fixed, glow plugs...

I have a strange problem with my Peugoet 307 sw 2007 Multidisplay shows ABS fault and the light is on on the dash board but at 3 workshops and different diagnostic tools no error when scanning however none had Diagbox.
I can't tell which sensor front or back right or left is faulty if someone has had the same problem or what can be done.Thankful...

Hi want your expertise for these two Lexi3 Diagbox as the seller claims them are genuine (Original tool) very grateful for your opinion.
and if one of them turns out to be genuine (Original)where would the price be.
very grateful

OK. So code is definitely 0952 which means nothing but here is the description:-

Telematics 1 problems exist
1.0952 FM2 Aerial Fault. No Signal

Now! When I looked at it yesterday, perhaps on a different system, it said FM2 Aerial Fault. Short circuit to open. Earth.
which is a subtle difference.

Can you search on descriptions or Telematics...

So I have a 2014 picasso 2.0 blue hdi
I have a p16a7 13 fault ...control of crankcase fumes heater

I can't find much info on this but I'm thinking its the yellow thing with wires near rocker cover
Just wondering if anybody can help identify it or know any details

Screenshot_20240906_073040_Chrome.jpg 20240906_065018.jpg

Ay up!

I have ABS problems! However, when I tried to use my LEXIA to figure out the problem, LEXIA threw a tantrum and would not work. This is when I discovered that the laptop had deleted all the files that worked the interwebby thing!

I have tried reinstalling Windows 7 but it refuses to recognise the wireless card. I've bought new LEXIA...

Hi can someone point me to windows 11 drivers for my lexia golden Firmware 921815C , this is what seller claimed when shipped to me i need interface checker + win 11 drivers x64 in order to use it latest diagbox ?

I have bought a 2015 DS5 on the weekend from an independent dealership and in true new car fashion, it has issues after driving it the 2 hours back home.

When on the test drive, it gave no indication of errors or faults whatsoever but is now warning me that I have 600 miles to top up the AdBlue before the engine will no longer start.

After...

Hi there,
Addition to Diagbox 9.68 MrRorry:

It looks like it was possible to use the 9.68 via VM, so that it is not necessary to buy the activation code.
According to my information, DB 9.68 is running correctly e.g. on workstation 15 or on 16.1.0, if the PC is suitable for the VM.
It should be a 64-bit system e.g. WIN 7 or WIN 10 64 bit. because...

Hi i am struggling with PSA Group i have diagbox, their software, activated, but vxdiag, cant read all ecu and all data properly specially on cars year 2020 or even cars year 2017 and up.... with bosch mts 6531 i see other ecu and other errors which i dont see with vxdiag but still i dont have the full picture... what tool i need to get/buy...

How do I get the build details for my Picasso vin VF7**************[VIN obfuscated, can be read by forum staff] will it show first reg details dealer etc.

Ok, so o have some difficult issues with my Toyota Proace ,built in France. (psa)

I have now tried several diagnostic tools, but it appears that this Toyota only accept a diag tool calked Diagbox.
Can use obd2, but I need more advanced tool.

Any tip where i can buy such tool for a good price ?

Thanks 👍👍

I have a 2016 Peugeot Partner 1.6 BlueHDi which my Lexia no longer wants to talk to and I have not been able to correct the issue.

Having had the Adblue tank problems, Nox sensor replacement and now (possibly) and Eolys issue, I needed a tool to save me paying £50 a time to diagnose or clear faults.

My little obd2 reader would clear the Adblue...

Hi all,

Car in question is my 2003 HDi110 DW10 Xsara.

When the car gets up to temp it puts its self in some form of limp mode when i have very limited boost. Ive tried changing the MAF sensor and N75 valves but no change…

Ive attached photos of what codes came up when it was scanned.

IMG_5894.jpeg
IMG_5896.jpeg

Any help would be really...

will lexia 3 and diagbox work on windows 11. i am having trouble with it. thanks.

Hi, I have a Citroen C4 Grand Picasso I Phase II (2013) and want to perform a BSI Reset. The instructions say to disconnect the negative battery terminal, but it's inaccessible. Only the positive terminal is reachable for me.

Will disconnecting the positive terminal instead of the negative still successfully perform a BSI Reset?

Hi all,

I've run into a very bizarre issue that I don't know the cause of. Up until now, I've had no real issues with Diagbox. My last session was 2 weeks ago where I cleared some intermittent diesel temp codes. I wanted to go back in yesterday and see if they had cropped up again, but I couldn't connect to the car. I was met with a screen like...

Hi I am getting an airbag fault B0002:64 Permanent Level 2 driver airbag line--Line present but not configured. comes on after I switch off and on again.
also only been present since using token on diagbox to reinstate active cruise after a crash.
Any help much appreciated

I cannot find the water temp sensor that
(per haynes manual) says because - it is petrol with air con - it should be on the side of the radiator ( LHS )

The thermostat housing has no wires anywhere near it - so that rules that possibity out !

It still has the original radiator with 29 07 1999 manufacturing date stamp still on it !

A new sensor...

Hi, I’ve been looking at the topscan device for issues with m 2008 C4 Picasso. I have a basic OBD reader that doesn’t pick some issues up and was wondering if anyone had this device. I’m currently trying to track down an issue with the locking system and an airbag warning light. Will the topscan read these codes and if possible could i use it to...

hi all so i have beeen looking at getting myself a lexia 3 and during my search i have found this

also this looks the same

apparantly this is the new updated unit and can do everything the same as the lexia 3
any thoughts would be great any knowledge would be awsone

cheers
Paul

Hi

I am trying to get a 2006 206 1.4 Vin VF3**************[VIN obfuscated, can be read by forum staff] up and running again. I seem to now have inherited this car as the owner has decided they dont want to deal with it anymore.

Immobilizer fault on dash no start, following has been done .

BSI reset as per forum, following observations, beeps test shows its seeing the key, I though...

Hi All,

New member but after some advice if possible...

I purchased a (cough) Vauxhall Vivaro Life a couple of years ago new. I know these things are mechanically identical to the Traveller/Spacetourer, so I've come to the experts as opposed to a Vauxhall forum 😄

The vehicle was sold as a 177bhp, with my V5C showing the max net power as 130kW....

After my battery discharged and jump started it,the blower as stopped working. I looked on utube but no help. Also the voltage stability module fitted on the front of the top of the battery is also faulty! Could this be a cause of no blowers. Thanks in anticipation

Hi all, so what i have here im pretty sure is a clone. Ive owned it for quite a while and use to use it a lot for a 2001 Citroen Saxo. I was pretty much able to do most thigs. However im so out of touch with were lexia 3 hardware has gone. Ive provided below as many clear photos as possible to help you hopefully identify if it is a clone, and if...

Hi,

I have an issue with the windscreen wipers on my Peugeot 508 RXH, 2014.

The right wiper does not extend more than half way up the wind screen. The left wiper apparently works as it should, however diagbox gives fault code B11B0 71 Wiper Control Mechanics Fault on the left wiper. There are no persistent fault codes on the right wiper or the...

Hi, as a new member please don't judge my ignorance. I have a C4 Grand Picasso 1.6TD semi automatic on a 61 plate, I only have 87500 miles on the clock. My problem is this on 8th June I had an injector 3 fault. The RAC mechanic came to my home and replaced the injector. However uit still diagnosed an injector 3 problem. May be a faulty injector I...

Hy

I have problem with my interface. Everything was fine and worked perfectly until I installed Scan XL pro 3.5.1 and Touch Scan 2.16.3 for other interface (OBD)

Now when I plug interface USB to computer green light flashes for two to three seconds and I get message on the computer that usb is not recognized, and the green light disappears..
On...

I have a fully chipped & working Diagbox interface, as I now have a C5x, is it worth keeping, is it compatible and will I be able to get the correct software for my Laptop?
Thanks in advance

Technically the car is not french but engine is renault after all, so please forgive me.

Qashqai 2012 1.6 Dci high mileage (over 200k), first realised there is a problem when car started stuttering slightly on the motorway. Eventually it stalled while driving off in a car park. Error P0488 EGR - throttle position control - range/performance...

Hi all,
Got a puzzling one for me and I'm really hoping someine can help me.

So, a few months ago I brought a second hand van. On the way home I noticed black smoke from the exhaust and then when I got onto the motorway the engine light came on and I entered limp mode. I went to the garage the next day and the above codes were given where I was...

Good evening, dear forum members!

I'm driving Citroen Picasso II 2017 (1.6 BlueHDi 120HP) VIN: VF7**************[VIN obfuscated, can be read by forum staff]
The car has been acting up lately (ABS error on 3600rpm, high consumption ~15l/100km, knocking in engine sometimes).

I was at my local official dealer here in Latvia (Andre Motors) and the guy there told me the car might need updates....

I've browsed a lot of videos and posts showing how to reset DPF Fluid after filling up, but after 3 hours in diagbox I just can't seem to get past this error in the attached screenshot. This error comes after entering the number of grams i've added to the tank. I assume there's another value I need to add somewhere first such as mileage, but can't...

Hi Guys!

First of all thanks for the help!

Before I describe my problem, I got a C5 X7 (2011) with the Philips Hifi System and currently no sound.

Through the recent months my soundsystem randomly stopped working. It started in the beginning of the year then the intervall between not working got shorter until it fully stopeed. So I obtained a...

Hey everyone, was wondering if anyone can shed some light on this... 2011 DS3 1.6 HDi 110BHP, 118K

I seem to keep having an Engine Fault: Repair Needed message come on the dash whenever I accelerate hard which puts the car into limp mode. Plugging it in gives me the code P0100: Quantity of air above the maximum threshold.

That message makes it...

I'm back on fault finding the cause of thick white unburnt fuel smoke during regen on my 2014 2.2 Boxer campervan.

Something I've noticed on the air intake 2 page of diagbox is the following parameter:

Status of the activation of the correction due to the oxygen sensor - Inactive

This parameter is always inactive during normal driving and...

Hi all!

Is there a way to check the genuine total mileage for the 2005 C5 through Lexia? In our country, it's an everyday practice to lower the mileage of any older (or newer, if they are high mileage) car to an eye-watering 200000 km.

I bought mine two years ago with around 220000 km, but I doubt it was that low mileage for a 2005 car. I mean...

I ask dear members to help me solve this problem
My car is a 2002 Citroen C5
Sometimes the check engine light comes on, and the engine begins to vibrate and make noise, and the number of engine revolutions does not increase when pressing the accelerator pedal, and the message “Anti-pollution Fault” appears with a significant decrease in the...

When I close Diagbox I don't get the question Do you want to save a report? I used to but lately I haven't. I have looked and can't see how to do this.

All the saved reports are from sessions several Months ago

IMG_5411.JPG

Hello All 👋

I’m hoping that the forum could help with ongoing issues I have with my C3 Picasso.

It is a 2011 1.6hdi 110 manual (8v engine) exclusive it’s done 52k miles. We got it when it had done 28k miles and previously we had all four injectors replaced at 35k miles when it started to cough on long journeys that would put it into limp mode,...

Hi,
I'm looking for a friendly 'lexia' owner near me (HD9) to clarify gearbox problem .
Had the car a year (2012 C3 Airdream) and had the issue twice, in slow moving traffic. Resolved after engine left to cool.
Any advice welcome.
Thanks
Gez