French Car Forum

Having made up and fitted a front sensor wiring loom following the wiring diagram in the Peugeot Service Box my diagnostic is listing all six sensors and their respective positions but indicates a ‘short to positive’ which I usually take to be an open circuit.
The connection of the new front sensor array has also created a fault condition which...

Do you know how to increase the volume of the parking sensors through Mirascript?
i used DATEXPLORER (v01.01)
Here’s the file, just show me where the parking sensor volume needs to be increased.

Hi,
Can someone please advise me for the BPGA module replacement for my car as stated in the title. The garage has quoted me for £1000 and I cannot afford that! However I am happy to get the part from Aliexpress/likewise places and get it fitted myself with help from a friend who knows cars.

However I don’t know if reprogramming is required for...

Hello all.

Looking for advice.

My father's Peugeot 308 has an issue with indicator not returning to it's original position. I think it was right turn. Left works fine. They took it apart in garage and didn't look anything wrong with the indicator switch itself. So advised to change the whole combination switch (squib). With all 4 switches around...

relay housing.jpeg Hello
relay.jpeg
Peugeot 207 / 2011 1.4 Envy

My dipped and sidelights stopped working yesterday. I checked the relays in the engine fuse board and found the middle one to be wet inside and corroded (I saw a video on youtube that said it is a common issue for the middle one to get wet due to a screen wash failure and capillary...

Hi people in my phone.
Long time viewer and now in need.

2013 3008 1.6 HDi.
A week ago, I climbed in and tried to turn engine over. Just clicked. Jumped the battery and all was fine.
Similar earlier this week so replaced battery yesterday (after running multi meter across showing little voltage). Car started. I did a motorway run with no prob....

(Peugeot 3008 2014 1.6l eHDi)

Okay so I'm looking for a bit of advice on this.

Injector 1 went a few weeks back, got a remanufactured injector and had it fitted.

The backstory:
Since I picked the car up, it has occasionally knocked and has been using more fuel than normal. This has been getting progressively worse, until yesterday I got to...

Today I noticed a lack in power and as the day goes it got worse, it won’t go up any incline the power is that low. It has started to emit black smoke when trying to rev the engine.
Any ideas would be much appreciated

Good evening all ,

I have a problem with my 1998 Peugeot boxer 2.0 injection petrol .

Starts first time every time no problems. Revs no problem .
Go down the road and coughs and splutters until it gets warm , and this can take up to approximately 15 miles depending on the weather . After this it runs a dream .

Things I have changed so far ....

Hello from Norway.
I want to relace oil on the atomatic gear and want to be sure to get the correct oil.
VIN: VF3**************[VIN obfuscated, can be read by forum staff].
Grateful for answers

My trusty old 607 just lost its ability to move.
After 345000 kilometers, the transmission gave up.
There has been signs;
- First, a slight judder when driving approx. 50 km/h with a light foot on the gas,
- followed by moaning, croaking noise coming from the oil pump / converter area while idling,
- culminating with no movement at all in drive,...

Hi.
Scanned my 2011 .2.0 hdi with Icarsoft and came up with 3 error codes.

P2297 oxygen sensor heating, resistance of the heating circuit outside range.
Which o2 sensor , upstream or downstream?

Car stalls after startup and driving off occasionally ,so it came up with two fuel pressure faults.

P2291 rise in pressure in injection rail too slow...

Hi, newbie here. My 2010 407 has a warning that dpf fluid is low. I do not know if it is a bag or a tank, most seem to think a tank. I have been told to use an Eolys fluid or just a universal one. Can anyone advise please? I would appreciate any help. Thanks in advance, Phil.

Let me state spelling was and has and still is a problem with me ive never been good at it even spell checkers don't seem to be of help to me as sometimes wrong words will be dropped and it makes me look even more stupid , if thats possible..

206cc why did i and what happend.

April 2021 cold hard frost weather was very cold at the beginning of...

Good morning.

Does anyone know the location of the siren unit on mk1 5008?

My alarm goes off if I lock the car with the fob and I think alarm might be faulty ( low battery) as car is quite old now

Thanks

Hi everyone just joined from UK but live in Spain ,I have a 2010 boxer done engine swap started and moved it outside was running for 30 minutes all OK moved it again and it cut out won't start checked all connections, nothing seems wrong ,got these fault codes yesterday's using autel . Fault code descriptions from first scan
P0603 intermittent...

Hi all, I noticed that piece of plastic from rear bumper is hanging. With closer inspection, I noticed that has no screws/clips on it at all. I am wondering what part should I order and is it easyily done. Screenshot_20250827_204141_Gallery.jpg

Hello all
I've been on the Berlingo M59 Forum but as the cars get older, the forum members leave and move on!
I've had a seat belt warning come on, on return from hols. 1.5 hours of it.... siren ramping up through three levels of pain.
I've worked out so far that:
1. the driver belt seems to be circuit complete when unplugged and open circuit when...

Hello,
I'm a new user of this forum and I have a problem with my 2022 Astra L hybrid.
The car was in a front-end collision, and the electrical system is slightly damaged, including the bumper wiring harness and the water pump plug.

Everything works, and it doesn't display any errors on the instrument cluster, but there are a lot of communication...

Hi,

I have a 1994 Peugeot 405 Le Mans and it has the keypad in the centre console (code is unknown)

If you turn on the ignition the keypad shows a green light but the engine will only crank and not start.

I've noticed that pin 10 on the double relay for the fuel pump is not being grounded from pin 3 on the ECU (Bosch MP3.2)

I also have no...

Hello my friends.

Peugeot expert 2 litre Hdi 2008.

No start but cranks away happily.

Scanner shows
U1118 no communication with body computer.
P1693 start up request not valid.
Key is recognised.
I have checked all fuses I can find.
Checked most wiring connections and clean.
Had a look inside Bsi all looks nice N clean.

Battery has been off...

206cc Roof acting like a stroppy teen.

My 206cc was parked up just before the mot expired & sorned for the winter. I did run it up a few times to keep the engine lubricated but didnt lower the roof enough times due to some rubbish weather & life getting in the way. Last week on a dry but chilly afternoon i started the car & thought lets put the...

I have a Peugeot 3008 Hybrid4 2019 with the eatn8 gearbox and I will do an oil change but could see in the documentation that the filling procedure is different on the HT12 and HT13 version compared to the HT8, HT9, HT11 and HT12 where you are supposed to add 0,263 liter after the drip.
How can I see and/or know the difference between this...

Hello to all.
I'm the new guy here and I'll be appreciated if someone can help me with error code that I read at Diagbox.
Today I drove at highway and get Engine fault: Repair need error,. After that error car act normally and after 10 minutes of driving SERVICE light disappeared from dashboard.

When I came to home I connected my DiagBox and...

Hi all,

2009 - 207 1.6 HDi

The battery warning light comes on with the ignition and goes out when you start the engine as it should.
The battery is in good condition & charging as it should, 12.6 volts before start, 14.5 volts when running so all good so far.

However, I noticed that if the engine is run with auxiliary belt removed so the...

Hi. As the title says my Peugeot 508 from 2011 has some issues with the radio and the little screen in the dashboard. I get among other fault code u1f0a 88. No communication with the canbus network. And the little screens just blinks. No buttons on the panel works. Parking assistant does work but does not beep.

Tries to switch the radio unit but...

Hello colleagues.
It seems that my car has a temporary short circuit, which occasionally causes an engine overheating alarm on the dashboard.
(The engine does not actually overheat. The diagnostics can continuously measure the temperature).

I found a blown fuse (F9) in the engine fuse box, but I'm not sure what its function is, because the...

I have been chasing a issue on my peugeot 508 2.0hdi and it looks like I have a knacked injector that is not returning anything fuel after carrying out a leak off test.
Do the other bottles look ok as I'm thinking it's just 1 injector failed?.
20250823_083402.jpg

Incredibly, the owner's manual for my recently acquired Peugeot makes no mention of what specification of oil to use. Can anyone direct me to genuine information about the oil requirements for a:
March 2006 Peugeot 307cc, 2.0i 16V petrol (143hp).
Thanks in advance.

Hello from Bulgaria, two days ago I bought a Peugeot 3008 GT 2023. I tried to check by VIN number for some information about the car, I paid on several sites, but unfortunately I did not receive any information, could anyone help with any information, thank you. I came across a topic here where a user asks if a certain extra could be added, for...

Hi All . . .
Recently purchased Peugeot 208 Allure, but only received 1 Key from the dealer.
I went to Peugeot dealer to get a replacement mechanical key and get it programmed.
(I believe that the 2nd/backup key has a transponder in it . . . )
However, The key arrived from France already cut, but the service people are telling me that it doesn't...

I am looking for any information about Electric Power Steering Rack from Peugeout 208 or Corsa F (2019+).
I need electrical diagrams, part numbers (electric / petrol) and a system description (overall any info that is available in documentation).
If someone has access to PSA documentation and can search for EPS, I would be grateful for help

Hi All,
I've got a 2011 207 1.4hdi Sportium and I was driving along when the pedal went flat to floor and couldnt select any gears, this happened a few years back and it was the slave cylinder.

Checked the slave cylinder, removed it and it split into two pieces. I fitted a new one and eventually managed to bleed the system enough to get pressure...

Ok - dont feel suckered in here - its actually a Toyota Proace, but thats just a rebadging exercise. VIN is YARXUAHZ8DZ039172, which I think indicates an AHZ variant of the DW10 2.0 engine.
Driving last night at 70 on the dual carriageway with cruise on, all of a sudden had a beep and the cruise dropped out. orange light and a dash warning....

Hello,

I don't suppose anyone has access to a wiring diagram for a 2010 407 Coupe 3.0 HDi do they?

The V6 HDi's weren't fitted with a low coolant sensor. In the 2.7 HDi there's an option to enable it in the BSI and people have retrofitted it without any problems. However, in the 3.0 HDi the option to enable the low coolant sensor has been...

Hi, I have a 206 1.4 petrol manual 2005 which I'm changing the clutch on.

I'm reassembling after fitting the new clutch - got as far as reattaching the gearbox, gear link rods, clutch cable, starter motor, engine mounting.

So drive shafts are still out, no gearbox oil or electrics yet.

The clutch pedal seems to behave OK now, but...I can shift...

Hi guys, I'm from Brazil and owner of PUG 508 2012 1.6 THP gasoline strugling to find some info about which oil is the correct to the vehicle. I contacted Peugeot dealership in my city but they didn't tell me if the car is a Euro 4 or Euro 5 vehicle. Is there any other way to know the car's classification so I can choose the correct transmission...

I have a very annoying problem with my car at the moment that it judders during acceleration and wont go past 3k rpm without throwing a P11AA at me. When accelerating on the motorway sometimes, i can get a P0234 overboost code.

The car is on 234,000 miles, at 223,000, it had a new turbo, egr valve, clutch, flywheel, glowplugs. At 228,000 it had...

Hi,

I have a problem with Peugeot 508 RX 2.0 BlueHDI 180 EAT 6. The car sometimes has full power and sometimes it doesn't. I have two errors in ECU:
U1318 86
U1318 83

I cleaned all fuses and electrical connectors in BSM, BSI and ECU.

Interestingly, the gas pedal sometimes works hard (it is hard to press) and other times works slightly.

In...

I have a 2011 Peugeot 508. The radio suddenly stopped working and won't turn on. The main display and parking sensors also don't work. When I try to turn on the radio, I can hear the fan, and then every 15 seconds there's a sound like a jammed CD reader. I've never used CDs, and I've tried everything, but there's no sound.
Here's a picture of how...

Hi All,

Does anyone have any experience in mounting a oil catch can on a T9 1.6thp? I'm trying to do both PCV breathers with separate catch cans but I'm having trouble with finding a suitable location to mount it?

Any suggestions?

Many thanks in advance

Hi all,

I'm getting the ABS & ESP warning error coming up on my dash and my screen. This has been happening for around a week and it's very inconsistent at to when it comes on/off.

My first thought was the brake light switch, so I have changed that, but still have the same issue.

If I start the van and the warning light comes on, I can more...

have changed the clutch on my 207 everything fitted as expected but when i put it in gear the wheels are not moving, it goes into all gears properly with or without engine running any advice please

Hello

Father in law has 2015 Peugeot 508. Very clean example. But....a week ago it dropped few warnings. ABS, roll back, ESP....
Scanned with Lexia and here are results:
ECU
U1213
P050B

ABS
C1336
C1391

BSI
B173A00
B180562

I am not sure if all those codes related to curent fault. Thats what Ive found.
Had ABS speed sensor issue on my Grand...

It's especially noticeable when pressing the accelerator in 3rd gear at ~ 50km/h. When the speed is constant it is like a rolling sound, like something spinning producing this weird 'electrical' sound - listen at 1:20m.

Similar whining is present at different speeds but at different frequencies and sometimes even if i press the clutch without...

Hopefully someone can help me, I went to the garage to get a new screenwash pump. When ai got the car back pump worked, as it was flying out on the rear window, but on the windscreen, icould hear the pump but very little coming out in drivers side and nothing on passengers side.
Garage tried telling me a washer had been damaged and will need to...

Intermittent failure / partial failure of the power steering which resets via the ign sw, all fuses checked , fluid changed , the garage has fitted a recon motor/ pump but the problem persists. Has any one had a similar problem I've run out of ideas and so has the garage.

Hi, was this model equipped with a engine splash sheet originally? Also there is no protection cover on the timing belt. I can obviously find out at the scrap yard but this is my preferred option.

Hello everybody.I have a problem with a peugeot 206 1.4 hdi.Before 3 weeks ago We have to much humidity in Cyprus,and in the morning I go to start the car she won't start.I try another one time I hold a long time to crank and the engine start,until now everything good,I go to work for 5 days and the car start like normal,in 5 th day when I finish...

Hi I have a Peugeot 3008 hybrid 2015 and on diagbox I have fault codes attached as pdf photo codes are P1AC2- reduction gear position fault and P1B70- electric drive machine position sensor fault and P1AC4- drive train fault could these faults be because of the sensor and where is the sensor is it the sensor mounted on the electric motor...