French Car Forum

Hello. The car is a Peugeot 508 SW 2.0 HDI 163HP from 2011. The gearbox stopped working in the car. It was repaired. The car has driven about 150 km after the repair. The problem is that the car changes gears for about 1 minute. Then the gearbox shifts from D1 to D5 and that's the end of the drive. The last time I was able to scan all the modules...

Hi

I had reason to take the locking ring off my diesel tank on the 407 estate.

When reinstalling, I noticed it had a arrow pointer but no visible marker on the tank body that I could see.

It looks about right as the ABS sensor holes are in the right spots, I can't screw it in anymore and no movement from the pump when pushed down.

Any ideas...

Hi,

After replacing the original but faulty advance solenoid (coded) with a non coded LUCAS solenoid, I can't start the car.
The new solenoid receives +12V correctly after I start the car with the key.

A diagnostic with PP2000, shows this Default :

ECU Engine / Permanent Fault. Pump Module locked.

Tried to remove F2 fuse : issue is still...

Does anybody know where I could find a fuel pump relay?

Bitron type 240.101 part number 9607540680

Thank you.

May anyone advise the location of this switch ? It shows in diagbox both as binary 1/0 & an analogue % depressed ? I am asking as sometimes I have to repeat the clutch / de-clutch 3 times to get the car to start. Its a 2016 508 2.0 hdi. Thanks.

They say that the Third Time's the Charm , so I'm hoping for an answer to this question (Previous two generated a bunch of lookers, and not one reply).

My Cabrio has this lever on the outboard side of the Driver's seat (Yes, she's a right-hand driver--shouldn't make a difference). The photo shows the lever in it's extended position, as it's...

Hi,

I have removed the bench seat from my Peugeot Boxer and replaced it with a single and now have an airbag light on.

After much research I have added various resistors to the occupancy detector (390?, seatbelt buckle (2.2k?) and pretensioner (2.2?) plugs.

I have an (unclearable) fault B0118:95 Permanent fault Configuration lost and I believe...

Hi.

So I have a car with 102kkm on the clock and it started to eat a lot of oil. I have to sip 1 liter every 850-900 km! Also the fuel consumption increased dramaticaly. Oil is also leaking on all gaskets around valve cover, which is very strange to me as when you open the oil filling cover, air is getting sucked in (so vacuum inside)... My...

Hi folks my names riess, new here and hoping that someone can help me with my issue that i have been trying to solve on my 2.0hdi dw10 engine with 140k on the clock for over a month so here goes!

The issue is that when the engine is idling it feels very much like i have the clutch at its biting point although its in nautral its a stumbling...

Hi! I hope you can help me. I bought a Peugeot 2008 year 2015, and I need to change the AC Compressor, but I do not have any manual that could provide the part number and with the vin number I can't find the part number. Do you have any idea how can I get the info without having to disassemble?

Hi, looking for some advice… I have a 3008 GT PureTech 1.2. Stock suspension, new bilstein rear shocks, new bushes, tires are in very good condition, on irregular/ uneven roads the rear end feels loose and wobbly.. I can’t seem to figure if it’s some issue with the suspension or just the way the car drives… it doesn’t seem safe to me.

might be...

I’m new to the forum and looking for advice on a recently purchased 2014 208 petrol Active 1.0. The car is one owner from new with just 20k miles. I’m happy with it in every respect but want to future proof it as much as possible. Apart from the obvious consumables like tyres, battery etc., I’m particularly wondering about replacing timing and...

Hi ,

I have a faulty 2007 Coupe - RT3 N3 Headunit , think its called a RT4 but not sure.
RT3 D2A-N3
e2 03 06046
96640242YP
354149010120070

Was updated with 8.31 firmware.

The harddrive had failed , new one in and all ok. Then by mistake update disk in again but the CD player is flaky and gets to various points in updating and fails....

Just changing the pads on the rear of my 407 and have a question. The BOL's say to press the piston back in with a C clamp but looking at the set up with the cable and piston it looks like it needs to be wound in. I remember with the BX front they needed winding in for the handbake to be reset.
I've tried with some glandnut pliers and although the...

I own a Peugeot 508 2011 semi-automatic, and I’m facing an issue with the gearbox.

Initially, the gearbox was not engaging at all and showed the fault code P0925.
To resolve the issue, I replaced the entire gearbox. After the replacement, the gearbox started engaging, but I got a message on the screen:
“Gearbox fault: repair needed.”

I proceeded...

Hi, I removed the 7 pin towing light system and now when the ignition is on the brake lights are on constantly.
The device removed was a ryder tf2218/7h smart logic, and it was installed using quick splicing connectors. Once undone the wires have been cut, soldered and insulated to seal them back up.
I've reset the bsi a few times but no joy. Is...

Hi,

Forum newbie here! I've just bought a 2010 308 SW with the AL4 gearbox. Everything works smoothly until approx. 30 minutes into a journey. After around this time the shift from first to second becomes very rough. It feels like it struggles to select second - when it starts the shift, the revs soar for a second (like it's in neutral) and then...

Hello,

I have a couple of codes that are a bit of a head scrather, don't know what to do with them.

This is on my Peugeot 5008 MKII 1.6BlueHDI 120BHP. VIN VF3**************[VIN obfuscated, can be read by forum staff]

Built-in systems interface BSI2010_EV
B1865 23 Lack of coherence between the status of the engine starting switch and the status of the built-in systems interface internal...

Hello everyone. I have a question about resetting the eolys additiv amount on the ECU. You see that the problem I have is that I don't have a diagbox or non other obd scanners that could pull this off. There fire I think I'm going to order one since my stealership asks 200eur for this in my opinion not complicated job. I have the error p1434 and...

'18 2.0l boxer

Does the rocker cover also contain an oil catch can/strainer as well as the pvc valve/diaphragm?

Also, can the actual pcv diaphragm be replaced on its own? (the round cap on covering this part doesn't seem to be removable??), instead of replacing the whole rocker cover?

Hi all, first post to this forum but I’m looking for help regarding my 2013 1.6THP pug 308.

Around 1 month ago, I had an EML with two separate misfires which a garage diagnosed as spark plugs, these were changed and the car was fine for around a week.

The EML light then came back on, fault codes P0087 and P0172 this time around, 5-6 different...

1.6hdi. Was driving along and there was a loud psssst noise, then big blowing noise as if there was no exhaust.

Looked at exhaust, all seems OK. Noise is coming from back of engine.
No power! Very loud.

Hi everyone,
I refreshed the fluid of my AMN8 gearbox by already known method of draining around 3 liters 4 times and after that adjusting the level. In some of fhe forums I have read that after changing fluid, oil wear counter needs to be reset with Diagbox.
In Diagbox under repear menu I could not find any option for oil wear counter reset.
Even...

Hello all, should have joined this forum ages ago being a Peugeot nut and having had loads of them.

Would be very grateful if anyone could help with a weighty problem. Just bought a 1998 406 automatic and noticed very early on that occasionally the sport and winter lights flashed simultaneously. Unfortunately not konwing anything about this...

I bought my Peugeot 3008 petrol auto 4 months ago the nearside mirror don’t close when locking car then works for a couple days/ the engine stop start works for a day then stops for a month/ the engine has gone into limp mode for 25 yards then clears this happens 4 times the last 2 times when in traffic dash saying engine overheating I herd elec...

Hey all,

I'm doing some fault clearing on my 508 and I can't seem to get rid of this one on the BSI.

----
B132A : Air conditioning circuit low pressure safety fault
Characterisation : Signal below the tolerance range
Status : Temporary
Location : local
Variables associated with the fault

----

Can anyone help with interpretation of this? Is...

Hi!

Does anyone know what the u3fff code on my 2017 Peugeot expert hdi 1.6 d could be?
It says ~ fuel high pressure circuit fuel pressure lower than the reference value

I’ve given it a recent service fuel filter etc.
could it be as simple as a fuse or sensor? tia

So I've just purchased a (2015) 308sw the car has 165k on it & drives like it's just out of the showroom. The only issue I've found so far is the alarm sounds when I lock the car with either keyfob. I've read on another website it's possibly a glitch with the bsi & corrupt firmware, has anyone else had this and fixed it? I'm going to replace the...

Hi all,

for some reason my mirrors are not folding, either by locking from the key of the button on the driver door.
i have tried the following:
checked the fuse
bsi reset
reset both windows ( hold down for 5 secs, hold up for 5 secs
folding mirror reset ( ignition on, hold mirror button down, ignition off, release button, hold button down again,...

A couple of weeks ago after filling with Diesel as I drove off the forecourt. My 67 Plate Peugeot 3008 1.6 HDi flashed a Check engine message which now comes up every time i start the vehicle. There is just the service spanner that is on permanent display but not the engine warning light. I had a cheap odb reader that didn't display any faults but...

Hi
i have a Peugeot 5008 1.6 hdi 120.
previous owner ran the eolyse tank dry.
it gave me these errors
P1434:96 multiplexed additive pump- fault in multiplexed pump
and
P1435:00 multiplexed additive pump - can fault or multiplexed additive pump fault.

so i bought a new tank/pump and i filled it with eolyse.
i tried to adapt the new pump but with...

Hello,
i'm having a problem and i haven't found one garage that can fix it, so im asking your help so i will try to fix it myself.
the car is peugeot 3008 1.6l thp 165 hp.
few problems actually which I believe related to each other, one of them is it has like small stutters that looks like a very small misfire.
other thing is that it lacks of...

Hi all,

I have problems with my Peugeot 508 2.0 HDI 163 HP 2011 and hope someone here can help me. :)

Problem with electronic parking brake is that it is not not functionating and weird things happens when pulling parking brake i can hear some clicking noise from back but the parking brake still wont work. Any help or advice would be...

Hello Everyone
I'm new to the forum and coming here after a week of internet search for a solution of my specific problem.

Car: Peugeot 1007
year:2006
engine: 1.6 petrol
transmission: 2 tronic

Car has an automatic gearbox problem. Has a dash on the display and refuse to display Neutral. I've been traying to get this car started for over 2...

Hi. I've installed a 2.0hdi into a Talbot express motorhome. Mated the engine to the original gearbox. Currently I've wired up the bosch single plug ecu but it won't start.
Hdi tuning ecu. Unlocked stage 2.5 with supporting mods. I've gone over the wiring again and again.
I need diagnostic equipment. I've wired the OBD. It's k line.
I'm...

Just following up on a topic brought up in my previous post on another subject.

I have a cheap (£20) OBD-II code reader - Streetwize SWOBD3. There are various free apps that can be used with it -

Car Scanner
Auto Doctor
Four Stroke
InCarDoc

Torque (this one costs money)

Does anyone please have experience and could say which would be best...

I own a Peugeot 508 sw 2012 and I’ve owned for three years and during this time my screen has never worked. When I first got it the screen used to flash a Peugeot logo and now it only lights up when I press the on button. What shall I do

I have a 2014 3008 crossway that is showing kph on hud and on digital dash. I'm assuming this is the default as I had a faulty SD card in my rt6 stereo. Thanks to a lot of help from here I have managed to install new sd card and software so that everything works except that it's in Km instead of miles. There used to be a setting in the car stereo...

Hi!
Any chance somone can give me wiring diagrams for the boot circuit for a 2014 Peugeot 5008?
For a while there has been a very intermittent problem with the boot not opening. It always righted itself so hard to get to the bottom of it. However, the boot has now stopped opening altogether and I need to have a look at it. I gather it is likely...

Hello,
I’m looking for help to get the steering wheel radio controls working on my 2000 Peugeot 206 GTI (S16, Phase 1).

When I bought the car, it already had an aftermarket radio installed. I don’t know exactly which original radio it came with from the factory, but the service manual includes a Clarion pin code note. Based on that, I believe the...

hi 207cc
i have removed and replaced the faulty rear parkings sensors ( requiring removal of the rear light clusters) and also the drivers side seat for a cushion repair ( requiring disconnecting the air bag connector plug under the seat. ( done with battery disconnected.
now its back together i get messages for faulty indicators and also air bag...

I'm unsure if I should put this in the 308 forum, but it does seem to be the same problem as described here.

On a 2015 308 I had disconnected the battery to try and locate an intermittent fault on the air bag. After re-connecting the battery and then locking the car using the remote key, the alarm sounds straight away. So I think that it needs...

Peugeot 308CC 2012 1.6THP (163 BHP)

Hi Guys need a bit of help with the location of the roof close switches on my 308 cc. I have the following Diabox errors and wondered if anyone has the servicebox info showing where these switches are located. Thanks

9884 Right Hand roof locked switch signal fault
98A0 Left Hand side Roof boot locking switch...

Experiencing fault code 0994 and 0EB3 not able to diagnose real problem do any body know why there is same code on BSI and BCSU car stops while moving some power related issue need help and suggestion do anybody know

Dear
A few days ago on the Peugeot 508 SW year 2012. VIN: VF3**************[VIN obfuscated, can be read by forum staff], when starting, the warning Parking Assistance Fault appeared, but after some time the SERVICE disappeared and the parking assistance was working.
The next day it appeared again however the SERVICE didn't go away and the parking help didn't work.
Using Lexia3 and Diagbox...

Hi, all!
We had the automatic gearbox and the torque converter changed in a Peugeot 407 SW, and currently trying to finish the adaptation process.

However after the adaptation was initiated and we went for a test drive after a few hundred meters we got a P0734 error message.
Is this normal during the adaptation process?

Thank you for your input!

The side and rear plastic trim connectors appear to be designed better than the German vans, in that they have little rubber washer/gaskets around them.

I'm building a van conversion and on the German makes these always get silicone sealed in to stop water ingress as it runs down and in behind the trim panels.

Has anyone ever had an issue with...

Hi all,

Peugeot 206 GTI 140 (yr: 1999)

1. Car is on 37k miles with around 15 main dealer services. Cambelt and water pump changed at 29k in 2020.

2. Has been running ok during my 12 month ownership aside from erratic idling when parked. Temp goes to about a 100deg and engine seems to be struggling to breathe, if that makes sense. splutters to...

Hello everyone.
I bought a Peugeot 5008 in 2021 1,2 (131) 6 st. Manual transmission.
I have a “clutch temp high, limit use of pedal” warning appearing, but only when using 6th gear? It does not generate any error codes. I think this warning is generated if clutch slip is detected.
I've read the forum, but I haven't found a solution. Maybe someone...

I recently refilled the Eolys fluid in my 2013 Peugeot Partner 1.6 HDi 90 and I am trying to tell the vehicle I have done so. I have connected up Diagbox 7.57 via a Lexia 3 Full Chip interface, and can perform a Global Test with success; all the ECUs are recognised except the engine ECU, which just says ECU not recognised .

If I try to enter the...