French Car Forum

Hi. As the title says my Peugeot 508 from 2011 has some issues with the radio and the little screen in the dashboard. I get among other fault code u1f0a 88. No communication with the canbus network. And the little screens just blinks. No buttons on the panel works. Parking assistant does work but does not beep.

Tries to switch the radio unit but...

Hello colleagues.
It seems that my car has a temporary short circuit, which occasionally causes an engine overheating alarm on the dashboard.
(The engine does not actually overheat. The diagnostics can continuously measure the temperature).

I found a blown fuse (F9) in the engine fuse box, but I'm not sure what its function is, because the...

I have been chasing a issue on my peugeot 508 2.0hdi and it looks like I have a knacked injector that is not returning anything fuel after carrying out a leak off test.
Do the other bottles look ok as I'm thinking it's just 1 injector failed?.
20250823_083402.jpg

Incredibly, the owner's manual for my recently acquired Peugeot makes no mention of what specification of oil to use. Can anyone direct me to genuine information about the oil requirements for a:
March 2006 Peugeot 307cc, 2.0i 16V petrol (143hp).
Thanks in advance.

Hello from Bulgaria, two days ago I bought a Peugeot 3008 GT 2023. I tried to check by VIN number for some information about the car, I paid on several sites, but unfortunately I did not receive any information, could anyone help with any information, thank you. I came across a topic here where a user asks if a certain extra could be added, for...

Hi All . . .
Recently purchased Peugeot 208 Allure, but only received 1 Key from the dealer.
I went to Peugeot dealer to get a replacement mechanical key and get it programmed.
(I believe that the 2nd/backup key has a transponder in it . . . )
However, The key arrived from France already cut, but the service people are telling me that it doesn't...

I am looking for any information about Electric Power Steering Rack from Peugeout 208 or Corsa F (2019+).
I need electrical diagrams, part numbers (electric / petrol) and a system description (overall any info that is available in documentation).
If someone has access to PSA documentation and can search for EPS, I would be grateful for help

Hi All,
I've got a 2011 207 1.4hdi Sportium and I was driving along when the pedal went flat to floor and couldnt select any gears, this happened a few years back and it was the slave cylinder.

Checked the slave cylinder, removed it and it split into two pieces. I fitted a new one and eventually managed to bleed the system enough to get pressure...

Ok - dont feel suckered in here - its actually a Toyota Proace, but thats just a rebadging exercise. VIN is YARXUAHZ8DZ039172, which I think indicates an AHZ variant of the DW10 2.0 engine.
Driving last night at 70 on the dual carriageway with cruise on, all of a sudden had a beep and the cruise dropped out. orange light and a dash warning....

Hello,

I don't suppose anyone has access to a wiring diagram for a 2010 407 Coupe 3.0 HDi do they?

The V6 HDi's weren't fitted with a low coolant sensor. In the 2.7 HDi there's an option to enable it in the BSI and people have retrofitted it without any problems. However, in the 3.0 HDi the option to enable the low coolant sensor has been...

Hi, I have a 206 1.4 petrol manual 2005 which I'm changing the clutch on.

I'm reassembling after fitting the new clutch - got as far as reattaching the gearbox, gear link rods, clutch cable, starter motor, engine mounting.

So drive shafts are still out, no gearbox oil or electrics yet.

The clutch pedal seems to behave OK now, but...I can shift...

Hi guys, I'm from Brazil and owner of PUG 508 2012 1.6 THP gasoline strugling to find some info about which oil is the correct to the vehicle. I contacted Peugeot dealership in my city but they didn't tell me if the car is a Euro 4 or Euro 5 vehicle. Is there any other way to know the car's classification so I can choose the correct transmission...

I have a very annoying problem with my car at the moment that it judders during acceleration and wont go past 3k rpm without throwing a P11AA at me. When accelerating on the motorway sometimes, i can get a P0234 overboost code.

The car is on 234,000 miles, at 223,000, it had a new turbo, egr valve, clutch, flywheel, glowplugs. At 228,000 it had...

Hi,

I have a problem with Peugeot 508 RX 2.0 BlueHDI 180 EAT 6. The car sometimes has full power and sometimes it doesn't. I have two errors in ECU:
U1318 86
U1318 83

I cleaned all fuses and electrical connectors in BSM, BSI and ECU.

Interestingly, the gas pedal sometimes works hard (it is hard to press) and other times works slightly.

In...

I have a 2011 Peugeot 508. The radio suddenly stopped working and won't turn on. The main display and parking sensors also don't work. When I try to turn on the radio, I can hear the fan, and then every 15 seconds there's a sound like a jammed CD reader. I've never used CDs, and I've tried everything, but there's no sound.
Here's a picture of how...

Hi All,

Does anyone have any experience in mounting a oil catch can on a T9 1.6thp? I'm trying to do both PCV breathers with separate catch cans but I'm having trouble with finding a suitable location to mount it?

Any suggestions?

Many thanks in advance

Hi all,

I'm getting the ABS & ESP warning error coming up on my dash and my screen. This has been happening for around a week and it's very inconsistent at to when it comes on/off.

My first thought was the brake light switch, so I have changed that, but still have the same issue.

If I start the van and the warning light comes on, I can more...

have changed the clutch on my 207 everything fitted as expected but when i put it in gear the wheels are not moving, it goes into all gears properly with or without engine running any advice please

Hello

Father in law has 2015 Peugeot 508. Very clean example. But....a week ago it dropped few warnings. ABS, roll back, ESP....
Scanned with Lexia and here are results:
ECU
U1213
P050B

ABS
C1336
C1391

BSI
B173A00
B180562

I am not sure if all those codes related to curent fault. Thats what Ive found.
Had ABS speed sensor issue on my Grand...

It's especially noticeable when pressing the accelerator in 3rd gear at ~ 50km/h. When the speed is constant it is like a rolling sound, like something spinning producing this weird 'electrical' sound - listen at 1:20m.

Similar whining is present at different speeds but at different frequencies and sometimes even if i press the clutch without...

Hopefully someone can help me, I went to the garage to get a new screenwash pump. When ai got the car back pump worked, as it was flying out on the rear window, but on the windscreen, icould hear the pump but very little coming out in drivers side and nothing on passengers side.
Garage tried telling me a washer had been damaged and will need to...

Intermittent failure / partial failure of the power steering which resets via the ign sw, all fuses checked , fluid changed , the garage has fitted a recon motor/ pump but the problem persists. Has any one had a similar problem I've run out of ideas and so has the garage.

Hi, was this model equipped with a engine splash sheet originally? Also there is no protection cover on the timing belt. I can obviously find out at the scrap yard but this is my preferred option.

Hello everybody.I have a problem with a peugeot 206 1.4 hdi.Before 3 weeks ago We have to much humidity in Cyprus,and in the morning I go to start the car she won't start.I try another one time I hold a long time to crank and the engine start,until now everything good,I go to work for 5 days and the car start like normal,in 5 th day when I finish...

Hi I have a Peugeot 3008 hybrid 2015 and on diagbox I have fault codes attached as pdf photo codes are P1AC2- reduction gear position fault and P1B70- electric drive machine position sensor fault and P1AC4- drive train fault could these faults be because of the sensor and where is the sensor is it the sensor mounted on the electric motor...

Hello. I own multiple cars with this gearbox which I am maintaining but this one gives me a headache. At 300000k km i replaced both main valves (still old style cause near me is no Peugeot dealer to update sw in gearbox ecu) because pressure regulation fault and gearbox was in limp mode, replaced oil, replaced oil pressure sensor (was showing 12...

Hi I'm hoping someone can help me with my issue.

I have a Peugeot 407 HDi 2.0 2006 and both left & right brake lights (tail lights) are not working.

The Third Brake light in the rear window is working fine.

I've checked the fuses they are ok.

Initial inspection both light bulbs were blown, so I replaced them and the new bulbs are not...

Hello. I have just bought a boxer van. It's a factory 6 seat swb low roof on a 16 plate, and covered 106k. There's very little service service history with it. I'm wondering what engine it is and if it needs a timing belt change. It's chassis number is VF3**************[VIN obfuscated, can be read by forum staff]. All I know is it's a 2.2 and it's surprisingly powerful and smooth. I would...

Took the car to a garage yesterday with this slight noise , he said it was nothing to worry about as yet.

Any advice?

Hi, first post here, hoping for some leads that might get to the cause of repeated fuel injector failures on my 3008. 2 went in 2022, then the other 2 in 2024. Each time there was a clear point where the engine went from normal to running on 2 cyclinders. All replaced with good refurbs at a garage I know and trust. Another went yesterday so it's...

autoradiossa ongelma. gps ei toimi ja päivämäärä sekä aika sekoilee. Kuuleman mukaan ajan voi määrittää uudelleen gps laitteen päältä kytkemisen jälkeen. En ole vielä testannut. Päivityksen saa myös jostain firmware 2.6 jotain.
Linkkiä kaivataan sen saamiseksi!?
Entä karttapäivityksiä näin vanhaan autoon, onko niitä saatavilla ilman rahallista...

I am dealing with a couple of issues at the moment.

I get the following error codes related to the EGR system 'P12B4 00' and 'P042F 00'. I already ordered a new valve module but have not received it yet.

I also get the following error it comes up multiple times 'U1318 82' (Communication fault with the built-in Systems Interface).

I am not sure...

Hi all, My car needs a replacement for the front FLEXI EXHAUST PIPE. If somebody could give me the part number, here are the details of the vehicle
PEUGEOT 308 1.6 HDI 2013 num. plate - GK63ZJO. Thanks
Also I found this on eBay :
IMG_0425.png

Hello,

I’m looking for the wiring diagram for the rear bumper parking sensor loom on my Peugeot Partner 2015 (VIN: VF3**************[VIN obfuscated, can be read by forum staff]).

The loom in the rear bumper is damaged, and I need the schematic to identify wire connections, and routing so I can repair it correctly.

If anyone has the diagram or can point me to the correct documentation, I...

Hi I have a Peugeot 307 14HDI, and for the past months the power steering randomly cuts out. The problem seems to mainly persist when I turn on the AC, in which case after some minutes the power steering stops.

When the problem arises I would need to switch off the car, let it rest and then after some minutes I turn it on again as if nothing...

Hey guys!

So I have a Peugeot 205, CJ 1.4 1990.

Been struggling with a soft and bad working brake pedal (a wet sponge). I’ve changed shoes (they’re touching the drums as should) wheel cylinders and master cylinder and there’s no air when bleeding the brakes. Front brakes looks quite fine as well. I’m thinking it could be some air leaks at the...

Morning all,
Does anyone have experience of replacing the front passenger window motor?
Diagbox indicates LIN bus communication failure, so the BSI can't sync the module and defaults to the fail-safe anti-pinch mode.
My main reservation about doing it myself is the risk of damaging the door card when removing/replacing it, as replacements...

Hi.
I have a 2015 1.6hdi with the robotised manual gear change.
It has been going into partial limp mode occasionally over the last year, it doesn't show any codes on the Peugeot diagnostics and clears for weeks before going into limp mode again.
Now whenever you start it up, after 30 second's it throws a engine fault message up and goes into limp...

Hi,
Have spent the day today trying to remove my front suspension struts.
The plan is to change top mounts and bearings as there is a twang/knock from the stering when parking etc as if the bearing isnt turning properly.

At the moment I havent even been able to get either strut out. In pushing the hub etc down to try and get the strut out gear...

Hey guys, hoping someone can point me in the right direction with the sound my 106 makes.

Something rotating in engine / gearbox makes a high pitched noise when RPMs are raised. Happens in every gear while driving and also in neutral reving when standing still, so it wouldn't have anything to do with moving wheels / drive shafts etc.

Very...

Last year my 205 failed its mot on the service brake efficiency specifically for the rear brakes being weak.
The rear brake cyclinders were changed at which point it was able to pass with 80 odd kgf of brake force.

this year however it has failed again measuring roughly 40 kgf at each rear wheel

Ive had the drums off today and given...

Hi there, I have a Peugeot partner tepee that I use as a taxi. All of a sudden my taxi wouldn’t start in the morning. I called RAC out they said the battery needed replacing which they did. The next day the car wouldn’t start again. The rac called out again they tested the battery which they said was ok and the alternator. They plugged it in and...

I appreciate the facility to request part numbers has been suspended for now but I'm hoping this is an easy one for someone 'in the know' to answer off the top of their head.

My 2019 Peugeot Expert 1.6 HDi (115hp) is dripping oil from the sump plug. It's probably due an oil change so rather than try and tighten up the sump plug I might as well...

Hi,

after almost 3 months having the issue, and after I couldn't find this solution that worked for me, anywhere in the forums (except from a russian forum)

I want to share with you my issue and the repair I did to the EPB, and hopefully it would help many more people in the future :)
I made a full video about the process, not leaving behind the...

Hello gentlemen.

I’ve been faced with a very expensive repair on my 508 hybrid. Apparently, it was caused by a leaking valve cover. Oil from the leak has dissolved a drive belt, which then got wrapped around pulleys and tensioners, causing extensive damage to these components.

Is it correct to assume that crankcase ventilation takes place via a...

Hello everyone.

I have a leak between engine and oil filter housing or oil filter housing and heat exchanger. I would like to replace the sealing. Which part do I have to remove that I can remove the heat exhanger with oil filter housing?
Because these parts have very bad place and I do not have a lot of free place.

Peugeot 308 2015 1.6 BlueHdi

Hiya, I've got a 2012 207cc

The manual suggests there's a master-fuse MF10 for power steering located in ' fuse box 2 ' - does anyone know where this is? I've lifted the main engine fuse box to reveal MF1-8 in a strip along the front, but can't find the remaining three.

I'm getting fault codes C1415 and P0606 with a power assisted steering...

Good Morning,

My current 508 was hit by another car, I have to scrape it. I'll look for another car. Which engine is most reliable? So far I used 2x 508 Hybrid4. First 220k miles, second 250k - engine still in good condition. Only thing I can complain is gearbox and speed of changing gears - my grandfather changing gears faster ;) ( I'm not...

How do I check if the trottle butterfly is moving 1.6 HDI 2008 90HP?

I unbolted it from the inlet so that I could see the butterfly.

On the obd2 it shows the pedal moving in percentage but I cannot see the butterfly moving; it's 1/4 open, the ignition is on but obviously the engine is not running.

I would have tought the default would be nearly...

hy and good pleasure today to you alls. ok let me direct to my question, how can i get the confidential card from my customer card while my customer buy this cars from used car and don't get a that card. i want that card because this ecu or bsi was corrupt... many like stop in the instructment appearal.. that blinking when i turn steering wheel...