French Car Forum

Hi I am getting gray hair over my 406er, so hope there are some in this fine forum who have the golden grain,
I have to admit with shame that no one at any mechanic forum in Denmark has been able to answer on the problem, and the answer from Peugeot DK, was: we have no idea

Peugeot hdi 2.0 engine code rhz

The car drove perfectly right until my...

I have pug 207 2010 sw lately im loosing coolent no overheating no mayo in oil cap after a long journey cant see any leaks but I have small leak in sump so.maybe mixed on floor I have no idea I want to take to garage but don't want him fobbing me off with gasket failure I had oit leak 2 year ago he said it was that I bought new engine had it put...

Hi!

I'm looking for some educational material about this platform. Principal diagrams, CAN communication, pipes and wirings and so on. I'd like to go a bit deeper into the logic of my new toy.

Any available information will be welcome. Thank you!

Hi!

I'm looking for a wiring diagram of the mirrors. The left one can be adjusted without any issue but the right one doesn't move at all. I'm switching the selector, so the problem should be between it and the wires to the door and the mirror. The car is LHD. VIN: VF3**************[VIN obfuscated, can be read by forum staff]

Regard!

My 407 came with the driver's side view rear mirror with a nice painted cover and one ugly unpainted (black) passenger rear side view mirror cover (I assume due to an unfortunate accident).

Googling I saw some Chinese chrome mirror covers that would fix the unpainted and hopefully make the car look smarter and cost around AUD$20 delivered (less...

How can this be adjusted ? Mine seems to have dropped toward the front of the car making the going up difficult I'm having to push the glass back about an inch then it goes up normal any diagrams , help , thanks

1.6hdi 2006 partner
How do you reprogram the central locking buttons after the battery has been replaced?

So, have the ASB/ ESP error come up (on and off)

Diag says C1325 left rear speed sensor aka ABS sensor faulty

Took the wheels off and the ABS sensor cable was a bit so so (eg 18 years old in the rain and wind etc )

Look at the Peugeot instructions and they said take the fuel tank out

Given mine was 3/4 full, that would not work for me

If...

Hi Everyone!

We have a Peugeot 5008 Allure S/S AUTO, 2018 May, 20,000km.
We are getting intermittent gearbox fault sign when driving, around once a week, it comes and goes and we did not notice any issue with the gearbox at all. We are currently driving across Europe, just bought the car in April and have a 1 year warranty from the leadership...

Hello from Australia!
I am new to this forum and am excited that there is a place for us to find and resolve together issues related to French cars.
I bought a 2011 Peugeot 508 1.6 e-hdi Active model a month ago and I'm getting some errors.
From the Subject line, I get the SERVICE light when I start the car and the Engine fault repair needed error...

Hello Mr Marc
Can you please help me with my Peugeot 3008 2.0 HDi engine code RHH 2013 with only one code on the ECU U1218 and the car on limp mode

I've been having issues with fault codes, my cars a 207 1.4hdi 2011 vin number VF3**************[VIN obfuscated, can be read by forum staff]

P1490
P242F
P2563

I have changed the turbo actuator position sensor and that has sorted code P2563 out.

So this morning while quite on the roads i decided to take it for a drive to encourage it to do a regeneration but unfortunately this did not...

It looks like I will be replacing the gearbox on my wife's car; 207cc, 1.6l vti, 2008.
I've seen other threads showing a position above and to the rear of the clutch slave cylinder/actuator lever as where the box should be marked with the number. I've clean the area and just can't find the number. The other location listed is a label on the end...

Had a little problem this morning, Started up and yellow triangle with exclamation mark beeped up, Van does though still run ok.
Ran through a scan and well wished i hadn't,
Dtc's are as follows-
U1401-Alternator Lin Network-Registering a fault on the slave node of the alternator lin network-Permanent- What does this all mean??
P0494-Fan-Twin...

Last year i fitted 2 new drop links to my car
Today they look like they have been on it for 15 years the rubbers have cracked so bad you can see inside them what the heck is going one ? Never in my days have i ever seen this.

Anyone else had the same with other components ?

Hi Guys and girls.
Im new here to this forum site so HI to all.
I’ve recently purchased a 2014 Pug Boxer with the 2.2 hdi engine.
The engine is (apparently) kaput. The guy at the garage said the piston rings have gone.
So., im on the case of sourcing another engine. These 2.2 hdi 2014(complete) engines seem hard to come by. I have seen a few...

When i put in the reverse gear i hear a long beeeeep for maybe 5-6 seconds and then it stops, and then nothing.....
Nothing on any display and no beep beep beep :-(
What is wrong?

Peugeot 307CC 2004

Good evening everybody...

Wondered if anyone else has had issues with a starter motor packing up and dying on them several times. I've had it replaced 3 times now in 2 years. What could be causing the issues. Any help or advice appreciated.

Allright guys,
After doing a ton of work on my 2008 308 1.6 HDi i've got a problem regarding the turbo's vnt, It don't work..
I've fitted two, recon turbos due to a faulty pressure sensor, the bugga located above the driveshaft that's a 'challenge' to replace.
With the old, original valve fitted, start car and the vnt's actuator arm moved fully...

Hi

I have a Peugeot 308 Gt 180 E HDI.

I have heavy black smoke under acceleration, so much so the DPF blocks inside a month. I bought the car with this fault & have gradually worked through it's issues. So far I have replaced the fuel filter as it was partially blocked, full service inc new air filter, new battery as it was flagging abs issues...

Hi all,

I've got a Peugeot 308 2.0 HDI diesel. Love the car but have started to consider adding a couple bits to make it a bit more fun. Looking at turbos and obviously it's not a car thousands are modding and turbo kits are hard to find. I'd wondered how easy/difficult it is to install on this engine. I know there is a version (might be the 1.6)...

Hello all. I'm trying to swap out my instrument cluster with one from a 206 automatic.

My Partner is a 2006 and the donor car is a 2003 206 and it has a gear position light in the dash. Will this work???

received_654726158978081.jpeg

:( so using the car today there was a creaking knock sound from the front so i stopped pulled over turned the steering wheel and front the suspension leg there was a creaking knock sound, i used the car a few days ago and it was fine.

Is this a dry mount bearing thing as the spring seems fine or is this early failure. #-o

Hi,during replacment seals of intake manifold on 307 1.6 hdi 110 I found that some these weird 3 yellow plastic caps are missing on tubes.Does anybody know what purpose is them?I cant find anywhere to buy them,does it have part number?Tnx in advance

Can you program any pug key to operate the central locking?

Hi I've noticed my dpf pipe is broken a new one is on order but any ideas of a temporary fix please,

I took the bolt out to find the end of the pipe has come off.

Thanks

Hello, I'm new to the forum and the French car.
I have a lot to learn with these cars, so I hope you guys can help me out.

About the car...
I bought my 2012 508 GT 2.2 Auto a few days ago. I believe the BSM is bad. As soon as you wake the car up, it has a loud fast clicking noise coming from the BSM module.
This is where it gets interesting. When...

Hello

I bought a second-hand Expert E7 taxi and I love it. However, I managed to get a towel stuck in the kerb-side rear sliding-door and now I am unable to open the door. Because of this, the taxi cannot be MOT'd.

My question is this. Do any of the controls in the cab lock the side-doors preventing them from being opened- bit like a...

Hi all,

The other half's 57 plate 207 (1.6 petrol auto) has thrown up the dreaded anti pollution fault. Happened about a month back, and local garage have had it in and recommended stripping the engine and replacing the timing chain, at a cost of £800. I'm really uneasy about it to be honest, on the basis that their diagnostics kit wasn't Peugeot...

I have a 2008 expert tepee. My suspension warning light came on yesterday. Ran global check today and communication error comes up against pneumatic suspension with fault saying cannot communicate with ECU or level sensors. Does this point towards a failed ECU? I have looked at all 30a fuses under dash and appear to be ok ( however fuse and relay...

Hi all,
I noticed that my car (508 2.0 163hp 2011 323000km) has developed some issue.
Issue is that when i first start my car in the morning, it turns on well, but engine noise is loud and i can feel and hear interior plastic moving (cant find proper term for this). Also RPMs are high on startup, and they stay around 900 RPMs for couple minutes...

The only way to close my bonnet on the 407 Hdi is to let it drop from around a foot and even then it sits very tight on the front bar panel.

I've screwed the rubber spacers on each side all the way down.

I've undone the nuts holding the catch mechanism to see if it can be adjusted but no joy, and its seems my next best option is to take the...

I have just replaced the Air-Con Compressor with a new one as the old one's seal(s) leaked.
I had the Air-Con re-gassed but the compressor clutch will not engage, I have tried turning the
interior fan on and off that had no effect at the same time reduced the interior setting to 18C, still not working.
Hopefully someone may be able to help me fix...

I have a cranking but not starting 407 V6 2004 petrol - was working fine but then started to to not restart when warm (not convenient when you are parked somewhere and want to drive home)

All the vital signs are there (spark, fuel pressure) but no power to injectors

Planet also says all 6 injectors are an issue (P020X) plus the U1108 missing...

Hello.
I want to clean the coolant system.
The total capacity is almost 10 litres.
What is the correct mix between Total brand concentrated coolant and demineralized water? 50% 50%?? 30% coolant 70% water?
Thanks.

Hi, My Expert has gone into limp mode but i cannot plug into it to diagnose the problem. The wires have been ripped out of the connector. i have trawled the internet looking for wiring diagrams, photos or youtube
but nothing for the MK2. Would anyone on this forum with an Expert the same as mine be able to help with a couple of photo's or even a...

Hi, short and simple but how easy would it be to swap a petrol 1.4 VTi in a 207 envy to the 1.6 GTi petrol engine, would I just need to change the engine and gearbox or would I have to totally rebuild the rest of the running gear

Hi all!
My manual Peugeot’s gearbox has died and I have called around a few wreckers to see if they have a replacement one. Sadly, I have been told several times to ‘put a bullet in it’ because it’s too old! I love my car and don’t want to give up on it. I am searching more alternative places but I don’t 100% know what gearbox code I need. I have...

Hi there
I see that previous this problem was discussed but need some help. My Peugeot 207 needs DPF filter liquid to be topped up. Unfortunately more garbage don’t do that and others ask too much money. For this reason l think do this myself and only find someone to reset system but need some help. Can anyone tell me what kind of liquid I need...

CODE 1AA0H/6816 REFER TO OEM REPAIR INFORMATION

Is it possible to install 2012 Peugeot 508 power steering pump on 2006 Peugeot 470 2.0 petrol engine?

Hi there
Hoping someone can point me in the right direction. My Peugeot 2008 130BHP 1.2 petrol 2018 model is typically now out of warranty and has an oil pressure warning issue. I thought I'd start by replacing the oil pressure switch and can't for the life of me locate it (my experience on working on cars has mostly been the classic mini's I've...

Morning all.

I have a Peugeot 5008 1.6 Hdi (DV6 engine)

I have and oil leak to the rear of the engine and judging by what it's covering, it's fairly high up on the engine.

I've changed the rocker cover gasket and despite not being able to find where two of the left over bolts go, this hasn't fixed it. The area is dry and the old one hadn't been...

Hello,
please help :cry: :cry:
I think I did a stupidity with diagbox tester. I tested in the acuator test needles and the light in the dashboard and since then they have remained like this, no more light on the needles and they are all at zero (oil temperature, coolant temperature, fuul indicator level, speedometer, ....) Does anyone know what I...

Hi

I'm looking for wiring diagram for Peugeot Partner (2007 year)
Vin VF3**************[VIN obfuscated, can be read by forum staff]
I need to find connection between engine ECU and BSI module.

I replaced engine ECU.
Last step is to synchronize ECU with BSI, but I have error - no connection between ECU and BSI.
I think I could break one of the wires because the're not in good condition....

Hi,

I have a 2008 Peugeot 207 CC (84k miles) that I haven't had long and it's giving me some grief! Might be a silly question but the car is making a strange whirring/grinding noise from rear left when in low gears - both accelerating and breaking.

I've also noticed there is dirt on the rear left wheel and that hub cap etc only?

It also take a...

After a little help if possible, Somebody has put a screwdriver at the side of the drivers door handle and bent the door around the handle, Where the end cap goes over, Not major but annoying.
The paint code shows 'EZRC' now I see a lot of adverts with the paint code 'EZR' and I see one for a Berlingo which I believe are the same?
Would an 'EZR'...

I have a 2007 Peugeot 207CC Vti 1.6 automatic with 131,000 km that thumps when changing from 1st to 2nd.

I bought this car as a non-runner so I don't know how the transmission operated before I bought it. I ended up putting a replacement engine in it. I have changed the transmission oil 3 times over 2600 km. I used Mobil ATF LT7114 and followed...

My 2007 Peugeot 207 CC came without an owners manual- mind you it also came without an engine that worked. I have subsequently downloaded a pdf copy but it's not the sort of thing you casually browse through like a book. But recently I came across a description of a second way of opening the boot that did not involve the button on the remote- see...

Hi, I hear a hum from the crankcase. Noise is heard while the engine is cold. I was told it might be from a nozzle, but I'm not sure. I'm uploading a link from a video you're making, the sound is coming from the crankcase and it's like buzzing. Please help if anyone knows what it could be.