French Car Forum

New member :-D

We’re looking at getting a 3008 this week but struggling to work out if it has the EGC/ETG gearbox, or the later EAT6?!

A car check brings back “Allure ETG Euro 6” but then under model info it says “Bluehdi EAT6 Auto” so a bit confused.

It’s a ‘65’ plate car registered in late 2015.

Any help is most appreciated!!!...

Hi Guys,
Just picked up a 2022 - 3008 Blue hdi 1.5 GT (128 kms on clock) on Friday PM.

So far, I have given it a good run, tested everything so far, BUT not quite got used to its wealth of IT yet :-D

Set 2 of the driver profiles to #1 France kms etc. and #2 UK Miles etc. -- no probs with that :-D

I have searched this board for my question and...

Hi all, I've got fault codes p0135, p0141 (O2 heater circuit both sensors) and p0443, p0444 (purge control valve circuit).
Cars a 2008 207cc. Does anyone know if this is likely just a new lambda required or possibly something more going on?
It just seemed strange to me that both sensors were showing faulty heater circuits and I'm not familiar...

my 207 HDi starter went bad so my mechanic friend put a new one in for me, at the same time he had checked some earthing straps and found them to be past their best, so replaced them

he also said one of the fuses under the fuse board in the engine bay was crusty, so he cleaned it up.

anyway the other day the car cut out on me just near home,...

As anyone who's read any of my previous threads will know, I have a problematical boxer.
A discussion last night with my son led on to the subject of the ecu,
Quick background info
Van threw up a fault code for the fifth injector, replaced this (and coded it) and found that 1> the metal clip had shorted onto the +ve wire to the injector, and 2>...

Hi all, I own a 2010 2.0hdi peugeot expert with a clutch problem. Long story short I bought the van last year with the clutch gone. Sent it to a mechanic who had a lot of trouble after changing the dmf and clutch in getting it to disengage. The fix was to blow out the pipe which connects to the master cylinder and pressure could then be applied to...

Well what a nightmare these pergeot boxers are... I have a 69 plate boxer that has a siezed engine, done 69k miles all services done as should have been, 4 year left on finance and is now sitting in the garage. Tried to get some help from Pergeot as this sound like a manufacturing fault to me, who expects a 4 year old van to do this, we have been...

Just bought a diesel 3008 & while doing a full service I wanted to top up the dpf additive, so when I dropped the tank who ever had done it before had broken the tank securing peg, so the only thing holding it up is the strap & the 2 plastic clips. Does anyone know if I can replace the peg or am I knackered ?

Hi Im looking for either a cylinder head or engine for my 1997 Expert 1905cc turbo XUD9
Can anyone help please

Hello
I have a peugeot partner 1.9d 2006
The gearbox is grinding like buggery.
Ive been looking for a second hand replacement but there seems to be a lot of different codes starting with 20T...ie 20TA...20TB...and so on up to 20TE...they all have another couple of numbers at the end.
Are the codes chronological....would 20TE be a later version?...

Hi, I've just bought a Peugeot Partner 2017 1.6 bluehdi 100 van, and have a couple of newbie questions. I posted on another forum but as that hasn't generated any response I thought I'd try here, hopefully that is okay.

Firstly, whilst looking for a van to buy I've driven a lot of these vans in various guises (Peugeot, Citroën and Opel) and in...

Saludos amigos, tengo un Peugeot 2008 año 2020 que tiene problema con el aire acondicionado, al encender enfría, luego se elevan las presiones y apaga el compresor, me arroja el código B132F 81, ya se cambió todo el sistema de aire acondicionado (evaporador, compresor y condensador, incluyendo la válvula del presostato) le probé incluso otra BSI y...

Hi everyone

Need a little help
207cc 1.6 think it’s the thp engine
60000 miles
Full history
Runs great loads of power starts fine ticks over fine
The issue is this
Leave the car ticking over and touch the accelerator pedal and I mean just touch it and the car feels like it’s dropping a cylinder.
It ticks over at a steady 800rpm if I read...

I did all 4 injectors on my daughter's 1.6HDi about 12 months ago and the oil is back all over injectors 1 & 2 and the underside of the bonnet. I thought the repair had failed but I now believe it is the intake pipework leaking and I would like some advice.

When I sprayed the cleaner over the injectors of the idling engine it rattled and...

Hi all. I have a 2021 208 with a manual gearbox. Does anyone know how to remove the gear knob? I'm trying to remove the centre console to gain access to the airbag module.

Many thanks
Chris

Hi got problem with peugeot 2008 , first is urea mean ad blue system
Problem is approx 1 month all lights on urea light Engine, Dpf fault on dash
Ad blue topped up pats fluid topped up both systems counter reset all lights off
After 4 weeks urea light on warning on dash engine shut down in 50 mls
Fault codes = P0A2 de nox system circuit
P0E8...

hi

i have a 2016 bluehdi 508

I had a problem with my gearbox last week. I started having problems shifting gears.

When I checked the engine , I saw that the water container was full of oil. this was atf oil. :cry:

My mechanic said the transmission oil cooler was punctured.

When we removed the oil cooler, we saw that water had mixed into the...

Hello
I am hoping someone can help with a filling quantity for diff oil for a 1997 Peugeot 106 1.6 Auto. My mechanic at work has drained the old oil and he said it seemed to be very little that came out so we are unsure. He seemed to think it would be 1L, but it seems it could be as much as 1.6-1.8L. Anyone know where I can find the capacity?
I...

Hi Everyone,

Sorry I could not find a topic exactly similar to mine so I am posting. Sorry in advance if already existing and thank you for directing me to it.

I have a Peugeot 308 Gt from 2016.
After a holiday in France where the car stayed in an airport car park for 3 weeks (when it was a little bit hot) I took the road back to the UK.
Around...

Can any tell me we're the fuel pump is in a Peugeot expert year 2008 and does it have one..I have dropped the fuel tank and it's not in there..

Good afternoon,

I have recently been through the ringer with the clock spring breaking on my Peugeot 2008 1.2 (2018).

The clock spring has been refurbished and reinstalled, sorting the traditional airbag, horn and other COM2000 warning lights.

Since reinstalling the COM2000, I'm having issues with steering angle sensor, specifically kicking up...

Hi all I've got a 306 cabriolet that needs the bowden cables on the soft top replacing, I can't work out how to disconnect them from the front of the roof anyone got any idea?

Hi all,

I bought a 3008 2014 model almost 2 years ago. Changed the SD card of the RT6 because it's corrupted. Thanks to Marc, I manage to revive the RT6.

However, I had 3 tyre puncture during these years, and no indication or warning pop up on my dashboard. Happened once after the puncture, I went to my usual workshop to diagnose my HPFP...

Hi everyone, I have a 508 with EGS gearbox and when the gearbox changes gears it makes a kind of clunk noise. It sounds like a double clunk, so i am assuming it clunks once when it pulls it out of gear and once again when it puts it into the next gear. It happens in first gear to second and also second to first gear. And I have the same clunk...

I have a 308 GT line 2.0 hdi. It has always felt slow for it's claimed bhp & hesitant to react to throttle inputs. It has been on Diagbox & no faults are shown. I tried blanking the EGR & the car is noticeably livelier & reacts properly to throttle inputs, however MPG is worse. Is this indicative of the EGR valve failing, all tests & calibrations...

Hello.

Im struggling with the heating in the cabin on my Expert van.
The temperature in the coolant are stable on 80 when engine is hot. Both hoses from the heater core are approximately even i temp.
The problem is that on the driver side the temp is good but the passenger side it is cold air.
The mixture motor is working as it should and that...

Whats the wire volt , amp power rating . Considering adding another light as the standard one isn't safe enough got the lights just need to be put in the right direction of wire , loom..

I drive a 508 SR E-HDI SA, 1560 CC 62 reg. I have owned this since 2016 and it has been reliable till now. The problem is it takes a while for the gear to engage from the first time I engage it and even on motion. So when I drive I have to apply the break which takes the gear to A1, on acceleration, the engine keeps making a noise and when it...

Hi everyone,

I hope you're all doing well and having a great day.

I'm currently experiencing some issues with my Peugeot 5008, a 2013 model with a 1.6L petrol engine. Unfortunately, I've got error messages indicating 'Parking brake faulty' and 'ESP/ASR system faulty.' I've had the vehicle diagnosed, and the error codes C1555d and U1308 have...

Hi got a alarm fault with 2014 Peugeot 2008 2014, alarm goes off after approx 2 mins
Common fault is bonnet switch and I can see someone has soldered the 2 wires to bonnet switch together
Question is the bonnet switch a open / closed contact switch ? so the wires joint together shows bonnet closed all the time.
Or does the switch give some feed...

Afternoon guy's,

Hope you're doing well and having a great day.

My vehicle it's a Peugeot 3008/2019 1.6 THP, It's a lovely car.
Unfortunately I ve got one major issue and few minors as well.
The major issue is my AC/ heating on the driver side middle and window part it's barely blowing any warm/hot air, compared to the passanger side which is...

I had a interesting experience with the ES9 this week, it being the daily commuter.

I had left it parked a week and went to start it and nada - battery was 9 volts. Sort of expected that as I did a lot of short trips the week before.

So pulled the battery out, recharged it overnight and refitted but did not start it until the following day.

On...

Exiting day yesterday!!
The van threw up a NEW fault code (this is to add to the ongoing but probably unrelated DPF issues)

Fault Code P2137 throttle/pedal position sensor/switch 'B'/'C' voltage correlation

Symptoms
Van was intermittently losing power while running from cold, (has done before so didn't think anything of it as assumed connected...

Got two fault codes which i can't delete. Tried with Diagbox and Thinkdiag+.
One is P160A in the ECU engine module and the second one is B1003 in the instrumental panel. Both has soemthing to do with the telecoding/downloading.

Anyone know how to get this off my car? I have a 308 T9 '15. Car drives good, no engine light or something.

Have...

I had the garage change a diesel injector on my Peugeot 508 SW 1.6 hdi automatic this summer.
Since the garage didn't manage to clear the fault codes and code the ECU with the new diesel injector number I did it myself with Diagbox. The didn't havde to proper tools for it.

I coded the ECU with the new code successfully but Diagbox tells me...

Hello,

i would like to know the difference between this two models of engine
HN02 Vs HN05

PureTech 1.2L Engine

Thanks you so much

2017 Peugeout 3008 wasn't starting and new BPGA was installed by dealer.....£600

Everything ok for a couple of days then same again, took it back to dealership as thought it was same issue or faulty part etc

Told us it was just dead battery, then said when they tested it after installing the new battery that the starrer was sluggish because the...

Fixed

Hi all,
I have a 207 1.6 VTi year 2007 that had an ECU fail.
I replaced the ECU + the BSI + the key and the key sensor.
I programmed the BSI and the ECU with Diagbox.
I had to change many settings because the donor car and mine were very different despite having the same engine and built same year (coupé vs sedan, automatic AC vs. manual, manual...

My car has developed a bit of a whistle from the passenger side (outside, not in the seat :lol: ), had a look today, and part of the mirror housing has come away. You can just see the gap at the end of my finger.

IMG_20231015_182202144.jpg

Wonder how much of the mirror I have to dismantle to get that back in :roll:

Hi,

tried to search forum but no success for P1828 :(

No crank was intermittent few months until last week no crank at all, repair shop had replaced starter when this issue started..

Today i read faultcodes and there is P1828 Starting prevention signal(start lock) short circuit to positive- code Permanent.
On instumeter cluster is only Dash...

Hi all knowledgeable folk

Has anyone got timing belt removal / installation instructions for a 508 2.0 hdi DW10F
VF3**************[VIN obfuscated, can be read by forum staff]
It belongs to a mate of mine, also a member on here., Come to line the crank/flywheel and camshaft but cant find the hole in the flywheel, I have the hole in the engine block behind the starter but cant seem to find...

Hey there car enthusiasts,

I'm reaching out for some much-needed help. Yesterday, I picked up my Peugeot 208 from the Peugeot garage after a major service and timing belt replacement. It's a 2019 registration with a 1.2l petrol engine and 44000 miles on the clock. Unfortunately, just three minutes after leaving the garage, my car broke down. I...

Hi there, I am replacing the head gasket on a Peugeot 107.
I have a slight chip in the thick part of the engine block
Screenshot_3.png
Just wondering what would be best and/or quickest way to fix, or if I need to at all. Spoke to a garage who told me a bit of liquid metal would fix it but want a second opinion first as never used before.My...

My Peugeot 807 (2.0 Hdi, 100 kW, 2013) is having starting/electrical issues.

First signs of failure were: when turning the key (starter position - 3) the startermotor didn’t do anything (no cranking or even clicking), there was just a soft/quiet click in the BSI (relay I guess). I did a second attempt turning the key and the starter cranked and...

I bought a 2010 model Peugeot 5008 in Greece earlier this year. As I drive up hills, a warning sign comes on which I have not been able to clearly photo as it goes as soon as I am on the flat. The word I remember is refroidissement, which I think is something to do with the cooling System. Can you give me any guidance s to what this may be please?...

Hi 2012 60,000 mile Partner Tepee 1.6 hdi couple of months ago intermittently on starting the car would start but idle was very low and no throttle response for couple of seconds then ran fine, no other issues then last week whilst driving abs light came on along with stop message, check engine light, speedo n/w and odometer display blank, pas...

Hi

Does anyone know the measurements of the engine mount screws appearing in the attached sketches?

Its a Peugeot 3008 2016 1.6 165 BHP vin VF3**************[VIN obfuscated, can be read by forum staff]

Thx

My dad's Peugeot boxer has decided on it's own accord (as french cars often do) that it does not want to start. After more diagnosing that I would like to admit my neighbour came by and gave me hand and we narrowed it down to the starter solenoid. Measuring the voltages on the connections on the solenoid shows that it gets constant power, and it...

Hi
My Peugeot 2019 5008 1.5 diesel engine VIN: VF~~~~ has become a nightmare for me and my family.

The car will not accelerate and the engine vibrates which I feel isn’t right, this was after the car was serviced.

The car has been in a garage for a month now awaiting an EGR Valve from the Peugeot dealer without any ETA given.

Where can I...