French Car Forum

A random question, i have a peugeot 5008, DW10CTED4 2.0 2010. On the partslink diagrams, after the turbo on the exhaust side, it shows a catalytic converter before it carrys on to the DPF. Can a DPF car have a catalytic converter too? My car is on 238,000 miles and im wondering if its likely to be blocked given the mileage?

Hi,

someone please tell me what the two sensors in front of the diesel fuel filter housing are for, one seems blue and the other brown. Im redoing my loom and i cant find connectors that go onto them so i think its better i know what they are.

Regards.

Hi. Further to my earlier post, I had a diagnostic check done and the fault lies with the transmission range selector also called multi use connector or transmission range selector
This part bolts onto the gearbox casing and connects the gear selector cable to the gearbox electrics/electronics. Apparently it is easy to replace.
Anyone know a...

Hi Folks,
Can anyone enlighten me on what the likely reasons that would be chucking up the following codes on a 207 1.4 hdi 2010 pre DPF?

P0069 manifold absolute pressure - barometric absolute pressure.

P0658 actuator supply voltage A circuit low

My reader doesn't list Peugeot so I selected Citroen so this definition may not be correct:

P1351...

I'm considering buying one of these. 72k miles, full history. Nice thing to drive.

Now, is EGC just Peugeot-speak for it's not EGS!! or have they actually made it more reliable?

Hi Guys, first post so introduction first, running a 406 2.1 diesel, on the 8B engine. She's an R plate so 98 if memory serves me right. Runs like a dream and give me 53+ mpg so not complaining one bit. I carry out as much work on her as I can ( use of ramps etc at work ) and keep her going as best I can.
My problem at the moment ( after I've just...

Hello all, not sure if this is normal but had my boot open earlier but when switching on engine I had the following errors come up
Boot open
Adjustable wing speed restricted (see manual)
Is this normal or is it something more serious many thanks. Sorry
I have a Peugeot 207 sport vti

Pls my Peugeot 407 won't start I use the diagnose pp200 to scare it I fund a fault permanent fault engine speed sensor no signal I change it and diagnose it no fault found there is spark plugs are OK the injections era OK but yet the car did not start my Peugeot 407 petrol engine 3.0 2004 model pls I need help

Hi anyone help me with this plz. when my car is parked i put my car into gear( my car is auto) put in reverse and touch the throttle it auto releases the handbrake but now it dont both forawd gears and reverse help

I got one strange idea and im interested is someone tried already that :)I have this Audi a6 noise insulation for hood,will it quiet more engine noise on mu 307 hdi if I put it under fabric insulation which is there on hood door?Tnx in advance

I have a 2003 Peugeot 607 2.2 hdi auto. The gearbox is usually very smooth, but lately , when selecting reverse it goes in with a bang, then will only go into 3rd when drive selected. PRND is shown on the dash
after switching off and on again, the fault disappears, but its getting more frequent
The handbook says abnormal operation but doesn't say...

just became owner of a peugeot 207 1.6vvt and im regretting already :roll: its come up with open curcuit fault bank 2 on diag and runs crap ,ive replaced both vvt solenoids and theres power to them ,if i disconnect one solenoid it runs ok anyone know where i can download a free wiring diagram for this or has had the same issues thanks

I've just had a 3 button remote added to my 2011 Expert. The car came with a 2 button remote but the locksmith only had 3 button remotes so used that. The 3 button remote works just fine, but only for lock / unlock, same as the 2 button.
The question is, can I activate the 3rd button via Diagbox, if so, how?

Hi
After warnings appeared on my dashboard, faulty breaking system, faulty ABS, i took my car to the garage, i was told that i need a new pump, at a cost of £800
Given its age, i could not spend that amount of money to get it fixed, so i have been looking to find a second hand pump, the problem is when i put in the make. year and model, there are...

Hi can anyone tell me the tappet settings for a peugeot 208 2013 1.0 litre eb engine

i have a 2008 peugeot 407 2.0 hdi , rhr engine which has developed a ticking/tapping noise when it warms up. i've changed the oil regularly every 3000 miles , had new injectors and cleaned the egr valve . the car has 96,000 miles . is this a tappet or chain sound ? any help is much appreciated !!!!

Hi.

I have a strong smell of gasoline in the engine area.
I see that the fuel lines are divided into 2, one for each injectors ramp. I can't see if the injectors lose.
In the pipes I don't see a leak.

What steps do you recommend to follow to find the leak?

Thank you!

I have diagbox 7.81 and peugeot 307 1.6hdi 80kw.Im interested how to test turbo pressure,and how to see does turbo has normal or lower pressure?Tnx in advance

Peugeot 308 1.6 HDI 2009. Recently developed this ticking sound. You don't hear it all the time. For some reason reversing after the engine starts seems to make it start. Sounds like a relay clicking.

Morning fellow Peugeot owners.

My next problem I have with my beloved (word used loosely) 308 cc is that the cabin heating doesn't seem to be functioning properly now.

I have the temperature on 26 Degrees or Hi and it doesn't get very warm at all. It helps to turn the AC off but the car soon gets condensation and steams up.

First thoughts were...

Just lately my engine light has been coming on more n more. I read the codes earlier this year and it said egr faults. Anyway, usual blast up motorway and it tends to clear. I’ve been planning to clean it out but as it keeps clearing I got lazy. Came home down M6 last night and after about a mile on an A road I had to stop at lights. Just before...

i have a 307 with a EW12 engine. for some time the depollution system faulty was popping up, within a short time i notice a very bad smell from the exhaust. not too long the car stop firing. each time a scan is plugged in, it points to cylinder 3. i have changed the ignition coil, changed injector, fuel pump, brain box and bsi, but it wont start....

Hi everyone I new so please bear with me.
I’ve got a 308 hdi 135bhp, 121k miles and I’ve only just got it but since I serviced it I get hesitation around 2k revs and it feels like it’s holding back under these revs but soon as I go over and cruise at say 2200 revs the car feels ok. It’s very noticeable at 68mph on the motorway on cruise as u can...

1) High all, after weeks of hell trying to get past the anti theft wall on my 2002 1.9 diesel multi space.
I throught I had cracked the problem. Only to discover when I remooved the bell housing holding the fuel stop solinoid in place. That there are three wires leading to the solinoid. I have been told that two of the wires are to do with the...

I have a 2013 308 active nav version i would like to hard wire a dash cam to car has anyone done this and have pictures or could tell me what fuse to piggy back and where i can earth it.

Hi,
would appreciate any help with this problem.

Just done a top end overhaul on engine and fitted new clutch, engine refitted but quickly started engine to check all OK (inlet ducting fitted and the cooling system not fitted) . Engine ran fine (just let it tick over for 30 seconds). 8-)

But after installing the inlet ducting, air box, rad,...

Hi,
I have recently had the timing belt and water pump in my Peugeot 206 GTI 180 changed. Sadly not by a Peugeot service centre.

Since I got it back the once great over taking surge it had is gone, it just slowly gathers speed and there feels like a drag of some sort.

The fuel issue seems related, I filled my tank, the estimated distance and...

I have recently had my transmission serviced and I bought comma mvatf transmission fluid LT71141from my local parts store and was told it was fine to use for my gearbox, I was wondering if it is ok or do I really need to use the Mobil transmission fluid as stated in my previous post my the very kind person who helped me out
Many thanks 😀
My...

My brother needs a new engine for his 2010 207SW 1.6 Hdi 90.
His garage is looking for a replacement but hasn’t yet found one with the same engine code which is DV6ATED4, the code from the vin is 9HX and the variant/version is WE9HXC.

The sticker on his engine is:
DV6ATED4 E4BVM
10JBBX312034D
and the engine number from the V5 is JBBX3120340....

Could a blocked DPF cause sudden breakdown and throw up EGR codes ?

My fault code reader is showing water temp at minus 40 degrees c. The only water temp sender I can find I just above the clutch (1.6 hdi fiat scudo/ pug partner) disconnecting that sends the dash temp gauge up to max and throws the fan on with dire warnings but does not affect the ecu reading from still -40c . Is there a second sensor for the ecu...

Hi again

In the absence of fault codes how would a 1.6 come out of limp mode ?

The only code I get now is P1351 Pre/post warm up relay, would a fault with the glow plug system perpetuate limp mode until rectified? My borrowed “Launch” fault code reader has the facility to test the relay and it can clearly be heard clicking . Would a duff plug be...

Hi all. Ive been having trouble starting my van in the mornings. The van has an xud9te engine. Unless I pump the black grenade thingy a load of times it really doesn’t want to start. I’ve been told it could be air getting into the fuel line?
Any help appreciated!!

Hi Everyone.

I’ve got another problem with my 308cc that’s just cropped up coming in to work this morning.

I’ve had a slow tyre puncture for a while and 5 weeks ago I got a nail in a second tyre so decided to replace the four tyres as they were all wearing low.

I had these replaced and had one of the tyres showing up on the TPMS after a couple...

Hello all.

I have a 308 1.6 hdi due to lack of use for the foreseeable future i would like to put a trickle charger on the car i have a ctek charger to use so a quality charger. I cant gain access to the negative terminal on battery and the earth post is on slam panel so cant close bonnet and lock car whilst charging.

Has anyone used one on...

I have just joined this Forum. It looks more knowledgeable than the alternatives.

My wife has a 207 CC on a 2008 plate and it has given good service over the years. Its not heavily used and is coming up to 161,000 km (that's 100,000 miles for the Brexiteers) and the clutch is going. I'm getting quoted over £470, which seems a bit steep. I've done...

Hello guys
I am from South Africa and drive a 2006 Peugeot 206 GTI 180.
The motor is basically stock with only the instllation of a CIA and catalytic converter removal. I am yet to do a proper connection for the CIA to the back-up air pump.
My question is, what other mods can i do for a good power gain. I want to keep the naturally aspirated. My...

afternoon folks, new member here so apologies in advance if the question has already been addressed - my warning light came on on my 508 2.0 hdi auto had it look at by a friend who said its fault code P2084 - which could be an exhaust gas temperature circuit range fault or particle filter temp sensor variation in voltage outside tolerance? the car...

Hello
Turning the key in the lock resulted in opening the internals for all to see - checked battery 2.84 volts so should be ok - carefully put it all together - tried five of Googled procedures to initiate the remote locking with the Two Button Key, no joy, but I can open/lock the doors and start the car with key insertion.
So no Remote Locking...

Peugeot partner 2013 model eng code 9hf coolant fan runs all the time hot or cold 1.6 diesel any ideas regards Mickeybo

If i start the car with the transponder from the key, but in very close to the key, and it starts and runs fine, then leave running and remove the transponder from in range with the key coil unit , will this cause any problems later, such as loss of recognition between the transponder and the system??

Hi I was driving the car a peugeot 207 1.4 petrol engine 2008 and there was a lound clunk and I pulled over and found the auxillary belt on the roadside. Got towed home and looked at the problem and the crankshaft pulley was missing.! It has damaged the crankshaft pulley hub, it has sheared off most of the collar that centres the pulley. I have...

hello I have a problem with my Peugeot 206 it makes a sound on a fuse box and it doesn't start..

Hi guys, I'm new to the forum, 2005 307 1600 petrol auto hatch owned for two years 70, 000 on the clock. so here is my problem it came with the car.
In park. key into ignition. turn the key click and buzz ignition on, turn the key to start nothing, so no power to starter. if I keep turning the ignition off then on again repeating this action for...

Hi everyone my Peugeot 207 auto sometimes when driving off the car makes a loud bang thump noise, when doing this it sometimes revs quite high and then goes into gear. I have had no warning lights or anything to tell me there is a problem.please could someone help
Many thanks

VF3**************[VIN obfuscated, can be read by forum staff] My peugeot 206 Central lock prob when i locking when i lock it will open when i close it will open

VF3**************[VIN obfuscated, can be read by forum staff] peugeot 406 AC PROBLEM NO COMUNICATING WITH AIR CODITIOING ECU PLS HRLP

hi to all .
first i tried to find a solution in this forum, to not do double post, but no success .

my car is a 206 van 1.4 hdi from 2006

vin- VF3**************[VIN obfuscated, can be read by forum staff]

ok , so my my problem is i need a new ecu , mine completely fried .
Anti pollution warning message/ abs /airbag / hand brack / speedometer .
i have planet 2000 , but no connection to...

Hi. Recently my car strangely behaves, randomly not cranking, while I hear just a relay clicking when I try starting the car. When I'm leaving the car to rest for a few minutes and I'm trying again, is cranking and starts. Problems with the battery and its connections out of the discussion because have been checked. My first thought was that might...

Hi all, I know this topic has been touched on many times, but I cant find an answer by searching on the forum !

Does anybody know which part number accelerator pedal will allow the speed limiter function to work on a 308 HDi (T7) ? I retrofitted a cruise / limiter stalk and turned it on in PP2000 - cruise now has been working fine for ages. The...