French Car Forum

Having partially fixed my DPF regeneration issue (so far all okay but still blowing a cloud of dark smoke on take off), Diag global test comes up with a permanent fault P1351 pre/post relay heating circuit / glow plugs.

I found the relay 0281003018 under the ECU but can't seem to spot the glow plugs themselves on the engine ?

Any diagrams /...

Does anyone have the diagram of the wiring for installing a aftermarket analogue alarm system in a Peugeot 307 break (2004)?
I need to know where to connect the cables from the alarm to.

I have a automatic AC in my 307 break. Is the ventilation control suppose to work when the AC is turned off?

Hi all, my 3008 1.6 hdi (9HR) died on me a couple of weeks ago coming home from shopping, at first, warning Battery Charge Fault came up as I parked in store car park. Checked alternator belt 'ok', Started her back up and no fault. As I pulled out of car park onto duel carriage way dash lights lit up and engine died, engine started back up before...

In short, lost the last original key. I have a new key without a transponder chip using the key code. The company came by to program a new key with a new chip (reading the computer (ECU)), but it didn't work. Couldn't get into the computer. Then bought a similar ECU with the corresponding transponder chip. The engine started 3 times, that was it....

Hi,

I spotted an unconnected negative wire and an electrical connector of some kind hooked up to the battery of my boxer van (2022).

Anyone know what they are for?

Many thanks
Peter

IMG_20241010_150245.jpg
IMG_20241010_150314.jpg

So i’m having a mare trying to proxy align my instrument cluster, diagbox wont do it, tried alfaobd getting failed any ideas?
IMG_4614.jpeg
Boxer 2.2D euro 5 2013 vin number VF3**************[VIN obfuscated, can be read by forum staff]

Thanks

So I have diagbox and have multiple airbag ecu’s listed. Have tried a guy to do remote coding via the psa network and he also gets instrument cluster and airbag ecu failed to align and advised to try the foat version to see if the cluster will realign I cannot get it coded offline or online via diagbox v7.57 &9.58 anybody got any ideas?
Turns out...

So here's my problem any help would be greatly appreciated. Have a XUD9A block uses a crack shaft casting 182 or 620 part number oem is 0501H1. Here in the USA these parts are hard to come by. So I was sent a crankshaft casting number 136 oem part number 0501N8. The oem crankshaft had a 8 web crankshaft design while replacement has a 4 web design....

I have gotten a 2006 Peugeot Partner 2.0 hdi but the VIN won't generate any results in Service Box or SSG Asia.

I need to find the correct part catalogue and repair instructions for this but have a hard time knowing exact engine model and gearbox.

Can anyone help me decode this vin? I would appreciate all or any help

VF3**************[VIN obfuscated, can be read by forum staff]

Hi Folks

I had the Timing belt and water pump changed recently. Since then the car is running in limp mode. A basic OBDII scan shows - P0341 camshaft position (CMP) Sensor A, bank 1- range performance error and a P2562 Turbo charger low boost error. I've not got round to using Diagbox just yet as I need to find my interface.
I've spoken to the...

Hi Does anybody know what the code card number will be to get into the marelli BCM? To do a proxy alignment i’ve getting asked for code card any ideas where i would find this I don't have any books or anything

Hi all.

Can anyone help me to get the official maintenance plan and schedule (the what and when do). I tried to get it from the dealer... no luck. I have the Haynes manual... well, poor, very poor.

Thank you in advance

Hi

My 2013 diesel Peugeot is in limp mode with a faults P1434 and P1435 on the fuel additive pump. It’s done 130,000 miles.

My regular garage changed the pump but it didn’t resolve the fault. He says he’s not the guy to take it further; and can’t recommend anyone.

I’ve taken it in for an initial investigation at the main dealer. They say no...

Anyone know if the scuttle panel on a 307 was sealed to the windscreen when they were new? Just had my windscreen replaced and fitter assured me that it was not supposed to be sealed.

I am hoping to get some advice on a 206 that has a aftermarket drivers seat fitted. I want to fit a resistor to bypass the airbag warning light on the dash.

There are 2 connector plugs from the loom. One is a green 3 pin and the other is a White 2 pin which I assume is for the airbag. Do I need to fit 2 resistors one for each plug? and do I need...

Hi
I am seeking to clean a few things in my engine, namely: the glow plugs, the inlet manifold, and fuel injectors.
To do this, it appears I need to remove a very solid metal bar/cylinder over the engine that I believe is some airflow (after the turbo?) cylinder.
Can someone help answer: can I remove this and then how? I have unscrewed the hose...

I have an elderly 2008 which, some years ago began to rattle/rumble from what I took to be the rear but which now seems to have settled in front offside position. Being ancient I dont do mny miles but it seems to be getting worse, I have taken it to three garages none of whom could identify it or its source though or they charged steeply for this...

Hi, first time poster in need of some advise pease , I’m self employed and own a Peugeot Partner 1.6 hdi 67 55000 miles
This is my 5th French van over the years, but the first I’ve owned out right, six years trouble free, serviced every year.
12 months ago the van developed a fault and a new catalytic converter and nox sensor fitted. My van has...

Hi,
Firstly I apologise if there's already a thread on this, if there is I couldn't find it. Car is a 2002 307 Rapier 2.0 Hdi with 5 speed gearbox which I think is an MA5. There was no horrid noises, just parked it up one night and when I drove it next morning no third gear, all other gears work fine so not the clutch. I've taken out the trim...

Hi

I'm making some external repairs to my 508, and one detail that bothers me is the presence of some cracks in the plastic frames around the sunroof (external part at the roof), they are frontal and lateral plastic frames in piano black.

I still haven't figured out if it's possible to remove just these frames, or if it's part of the entire...

Hi everyone,

Was recently given a 307 2.0 petrol with the Tiptronic transmission. Realised after a couple of days that I don't remember when last I saw one on the road (any variation 3/5 door or Estate).

I actually purchased this vehicle new at the end of 2003, then gave it to my folks in 2006. That makes it 21 years old, give or take. It...

Hi All, I am thinking of buying a 508 for the wife a 2013 one.. What are the main failure points on them to look for. Is the 1.6 more or less reliable or is it much of a muchness.

So I've got the diesel additive warning message on my 2010 peugeot 308 2.0 HDi 163 hp.

I found ample information on how exactly to top up the PAT fluid tank but I stumbled upon quite a few difficulties exploring the diagbox software. I still haven't done anything, I am trying to find out four things:
1. How much fluid do I need
2. What fluid do I...

Hurray peoples,

today i was able to solve the low oil pressure message on my car.

Since i've read many and many articles and watched videos about this subject without finding a solution, let me tell you what happened in my case.

Off course when the problem first started, i've looked on internet as many does, and found every possible solution....

A good few years back I caught turbo failure very early on, (took engine out, cleaned up top end) replaced turbo and, as recommended, changed the turbo oil feed pipe, banjo bolts and copper washers.

At the time of the rebuild I had issues getting the block end of the feed pipe's banjo bolt connection to be oil tight. Ultimately cured by annealing...

Hi,

Here goes -

Having a few problems with Mk1 Peugeot 3008 2015 (65)

Car was pulling to the left a couple of months just before seeting off on holiday, there was also vibration there indicating a wheel was out of balance, although there has always been a slight vibration in the couple of years weve had it.

Got wheel alingment done at a...

Hello!

Wher is located fuel filter, Peugeot 3008 MK2, 2019, diesel, 1.5 HDI?

Regards!

As above really, I am hoping somebody might be able to tell me if there should be something plugged into the EH2 NOIR/BLACK socket on my BSI.

I am having all sorts of issues and I am wondering if it could be related to this. I can't see a plug anywhere. Any information would be appreciated!

Vehicle make PEUGEOT, Date of first registration September 2011, Year of manufacture2011, Cylinder capacity1560 cc, Transmission Auto,
Fuel type DIESEL.
Hello, I have problems with my car. When the car is driven and the throttle is pushed for more speed the car comes up with Engine Fault STOP. Then is seems to go into some kind of limp mode not...

Hello guys,

I am new to this forum, i wouldnt bother you with this problem, but i couldnt find anything that would help me to find solution to my problem.

Car is Peugeot 508 2011 163 HP with 350 000km, car runs fine and everything is great except that when i start the car i get error message gearbox fault an i cant use shifters behind steering...

Hi,
I was wondering if anybody has the details for the bolt sizes needed for the undetray cover for Peugeot 308, 2012.
I have a picture below, referencing the middle (large) cover and bolts needed.
I understand that it might be difficult to find the original parts but would love to know the sizes of the bolts to try and by at a hardware store...

Hello everyone,i'm the owner of a 508 RXH Hybrid4 and the nightmares never ends whit this car.
while taking of from an intersection,like I normally do,the car completly went crazy going into limp mode and giving me the message(Parking brake fault,stop the veicle immediatly). Car is dead and i can't start it in any mode so I take it home whit a...

Hello, I have a Peugot 207 HDI 1.6 (2007) 90hp and I want to transform it to be as powerful as it can be... I am quite new to doing custom builds but thats why I am here asking for advice.

What engines would fit best in the car and what else could I do to get the most power out of it, e.g; 500hp or something.

Just bought a 2014 3008. The door mirrors never folded when locking. The other day was adjusting mirrors when noticed when adjuster is set in the middle and pulled back both mirrors twitch as though trying to fold. Also this happens when locking and unlocking. This affects both door mirrors. Question is have they been deactivated or have both...

Hi guys
i would like for some help please
208, 1.2Y, 2019
42 KKM

Last week 3 warnings appeared on my dash:
TPMS
Wrench
Control to prevent wheel slippage

i scanned and i saw this attached fault code : U1213 81

any leads?
Thanks a lot

Hi!
My 308 1.6 VTi made in 2009 has the AL4 4-speed automatic transmission which shifts roughly from 1st to 2nd gear, every other gear changes are smooth. The car has ? 150K kilometer mileage with no gearbox ATF fluid change.
What could be the issue?
Thank you.

Having cracked a rear fog unfortunately water crept into the parking sensor and into the wiring loom. This resulted in intermittent faulty sensors and finally the system stopped working. 4 sensors were changed and the wiring loom replaced. This did not resolved the issue. The ECU was then changed. Upon plugging the diagnostic in, faults still...

Hello, because of an error, I had to buy new gauges for our Peugeot 206 (MUX). The new gauges have all the needles (fuel, temperature, RPM and speed) set in bad positions so they show bad info. Is there an easy way to reset them to default positions? I no longer have old gauges (they were swapped for repair for the new ones) to get positions from....

Hi all, I want to get a new blade cut for my peugeot partner online. I have the 2 barcodes with codes below, that came with the owners manual.
Would anyone be able to explain which digits to use to order a cut key and which to programme key to van.
I hope @wheeler will see this post, pretty sure he will know exactly.
New here, so not sure if I...

Hi All.

I have a pronounced engine vibration. It’s most noticeable on tickover.

Clutch in or out doesn’t seem to make much difference. I’ve recently passed an MOT so unlikely engine mount. I’ve had a garage suggest crank pulley but this was checked and ruled out. He thinks probably DMF although there is no rattle or metalic noise that’s...

Hello gentlemen, I am the owner of a Pejo 207 1.6 HDI 2009 model vehicle. My vehicle stalls while driving, and when I wait a while and start, it starts. There is no error when connected to the computer. I replaced my vehicle's diesel pump sensor, rail sensor and crank sensor, but the problem continues. The problem happens a few times a week or...

Hi,

Proud owner of 1.6 HDI, got a quite a bit of a problem here.
I've been driving Peugeot Partner B9 1.6 HDI 2010 DVE6TED4 for quite some time and it hit 420000km lately, overall no problems until now.
P0299 Underboost, i checked the turbo, it holds vacuum and is fully engaged at idle ( :?: ) , no hissing when i step on the gas, cleaned the...

HI,

I got myself a 207CC from 2007 and initially everything worked fine. However, recently the roof does not open complete any more: the windows go all down, the boot opens fully, the roof starts opening but stops after about 10 cm. I'm pretty sure one of the microswitches is the problem here, anyone know which one this specific is? I'm...

Hello there,
I have a Peugeot 206 and lately it starts up rough if it hasn't been driven that day, idling at 300-400 rpm then jumping to a normal 900 rpm after 3-4 seconds

It has to be noted that when the car starts up this way, the airbag light goes on, and when I restart the engine after this rough start it starts up normally, idling at 900...

Got a mk1 Peugeot 3008 1.6 BlueHdi that has a leak at gearbox on driveshaft seal. Just going to change both while at it and I am hoping someone will be able to shed some light on how much oil the gear box takes as I know you drain completely then refill with correct amount as there is no level on it.

Hi all, I'm new to the forum, so apologies if this is something obvious, but I've looked on several forums and haven't seen anything quite like this.

So I've had my Peugeot 2008 (2015 model) for just under a year. Its on about 64k miles. The previous owner serviced it every year and it seems like they really looked after it, but the past couple...

Well I thought it was about time to start recording any developing issues on Sylv's car and start a blog. May as well start as we mean to go on!

What fun it is turning out to be...

Basically did the timing belt and auxiliary the other week including full coolant drain, major service and replaced the fan resistor module with genuine. All good....

Hi, on our Peugeot 206 (1.4i 55kW, 2005, automatic transmission) the temperature gauge is not working. The coolant temperature sensor was faulty* (no data on the driver cluster, nor on diagnostics) and I changed it. After changing the temperature sensor, the data is shown in the diagnostics tool (Generic OBD scanner and clone of Lexia) but on the...

Are the front driveshafts and engine/transmission mounts the same as a standard 2.0l AMT6 model? the vin no for my 3008 is VF3**************[VIN obfuscated, can be read by forum staff].