French Car Forum

I have a 18 Citroen Dispatch MKIII 1.6 Hdi that's showing an abs fault (and others I'm assuming that relate to not picking up the speed correctly).

On Diagbox it reads C0037 11 Rear left wheel speed sensor permanent fault, short circuit to earth. With no speed showing (the rest show 0 km/h).

I've replaced the rear wheel speed sensor however the...

I all,

I have a Peugeot 5008 1.5 bluehDi (2018) and I have a Lexia3 Diagbox 9.91 that is unable to connect to the ECU. I´ve been told that, for cars after 2017, it´s mandatory to have a PSA account (not Service box) for the system to comunicate with PSA servers.

This situation happened after an engine software update made in a Peugeot official...

I all,

I own a Peugeot 5008 (P87) II GTLine 1.5 BlueHDi 130HP - December 2018. At some point, I bought a Vgate iCar Pro BLE 4.0 OBDII and FAP app. All worked like a charm for some time. At some point, during a visit to Peugeot workshop (adblue reservoir and DPF substitution) they updated ECU software (at least they told me that) and, from that...

I bought a lexia 3 and I can't connect to the car. I tried in every way to update the firmware but it doesn't want to. Is there any other solution? Possibly which component could be defective in the tester to replace? I leave a video for you to see. thank you!

Hi not sure if anyone could point me in the right direction my 2013 2.0hdi van VF7**************[VIN obfuscated, can be read by forum staff] went into limp mode recently only had a cheap code reader with me which suggested a Maf fault Ive since read it with a snap on solus which gave the above codes relating to quantity of air greater than expected and cold air greater than expected. After...

Hi everyone, I have an ongoing issue that may have several parts to the solution, meaning I may have several unrelated issues. Van has 180k on it.

Main notable point is Losing Power (Boost?), Erratic Rythmic Idle that can stop if you turn the steering wheel for instance, intermittent No Response from accelerator pedal for about 1 inch of travel,...

No and I would advise against playing around and changing anything. I've had to deal with several cases where owners have changed things and their vehicle was left inoperative afterwards.

What is often shown in the Menus does not mean what you think it does. As the BSI's are used across a range of marques and vehicles, there are some settings...

After years of service my Diagbox system came up with the VCI is not connected screen saying please connect a VCI. This was not normall as my Lexia 3 tool was plugged in and I had not had the information window come up saying it had been connected to my usb port. After reading other forums, if the host machines device manager shows unknown device...

Hi.
Wondering if anyone with access to SEDRE would be able to help me... My laptop refused any further cooperation so can't check it myself. I would need wiring diagram for Saxo indicators...
Thanks
Ben

Hello again.
Thiw time I would like to know if someone has found a Xantia compatible obd wifi scanner. I know that the communication protocols are not OBD, just the interface. So, I 've heard that Lexia is the apropriate type of OBD scanner, but I don't know if there is something small like the ELMs, but compatible with the Lexia. If anyone know...

I have a 2015 Citroen C4 grand Picasso 1.6 blue hdi.
We recently changed the battery. Following this the electronic hand brake won’t go on or do anything. There was a period of cold weather so we thought it may have something to do with that. Now the car won’t go into gear when you start it but the gear stick will move when she’s not running....

Hi all,

(now edited to include forum-hosted images - thanks chaps!)

This is my first foray with Lexia - thanks to a very kind local forum member who has kindly lent me his own kit, so that I could have a look at what is happening to our 2006 2.2Hdi C8. MASSIVE thanks to him, for starters!

Our C8 has been in my care for the last 75k miles of...

Looking for some help please. I want to carry out a compression test on my 2012 Citroen C5 MK3 1.6 petrol THP (Prince engine) as I am having trouble with number 3 cylinder not firing even after changing the coil and spark plug. The cylinder already has a lot of petrol in it so I want to stop the fuel pump from running by removing a fuse before...

For this vehicle just connect the USB to your laptop, connect that to the VCI (Main Unit and from there, the other connection to the ODBII Port on the vehicle.

Yes, the VCI is powered via the USB. So make sure that your laptop power saving features for USB ports are disabled! You may need to go into advanced power settings for this, look for the...

diagbox fresh install not working uninstalled but there are still remaining files i cant remove any help would be appreciated

Hi all,

I am trying to get Diagbox working so I can initialise a replacement NOx sensor on a late 2016 DS3 1.6Hdi. I bought the full chip kit from Easy Diagnostics, and after a little IT battling, I have managed to work through the various installation versions, v7.02, v7.57 and then a number of interim steps to get to v8.17 which is the latest...

Pre Heat test fails - with Diagbox - won’t start when core plugs require a temp of over 0c

Hi All

Looks like my heater plugs are not firing up, I’ve replaced the relay and there’s 12v at the relay, though nothing get to the plugs
Running a test with Diagbox 9.96 I get the attached
Any help or advice would be appreciated

HI All
can anyone tell me does this look like the MAF temp has failed,
this is looking at the car first thing before it’s been started in 12hours and not actually running, what throwing me is that there are other temps reading in the 40's even though it’s not been started, unless its remembering these temps from when it was last started ....

Hello from Brisbane,
Is there a fix the error U1134 , on my Citroen C4 after replacing the stop start capacitor and the battery and now I have this error U1134 nobody here seems to know how to fix it i have cleaned and checked all terminals.

Hi all

Can anyone assist me with this please?

When connecting diagbox v9.68 on my 2015 308 HDI 2.0 GT i get 'ECU not recognised'

It has a stupid fault where when it is below 10c outside the coil light comes on the dash and the push button will not turn the car over

I’ve replaced the heater coil relay and resistance on the plugs looks good, I’m...

Hi Guys does anyone have an interface update above 4.2

IN SOME CASES THE renault laguna ii auto warning light orange indicator light on the dashboard will turn on, butthe car keeps on driving smoothly without any problems. What should I do?
Manufacturer:RENAULT
Model:LAGUNA HATCHBACK - 2.0 16V Dynamique 5dr Auto
Year:2004

Transmission:Automatic
Engine Size:2000
First Registered:30/04/2004

Evening all,

The wifes C4 has started moaning about an ABS/ESR fault and the hill assist feature has stopped working. It started as intermittent and would do it once every now and again but this week it’s become permanent.

Unfortunately my version of Diagbox doesn’t like talking to the C4. Is there a newer version that will run on the clone...

Hey.
I own a 1999 Peugeot 205 1.4 with an original immobilizer.
In recent weeks, the immobilizer has gone crazy and no longer requires a code to drive the vehicle and automatically there is a green light when the switch is turned on.
On the other hand, it cuts off the fuel/ignition in the engine during the drive or while standing and constantly...

Hi,
I have been running Diagbox 7.02 quite reliably for some time now.
I have also been considering upgrading to 7.58, (the option for which came with the purchased kit).
Knowing how shaky and tempremental the whole system can be though, I wonder whether it is best to leave well alone, rather than try to fix something that isn't really broken?...

Hello. I bought a Lexia/Diagbox in 2014 for my 308SW which I sold a few years later, the car not the diagbox. I’ve now got a September 2017 2008 and find there’s no 2008 listed, I’ve also been told that my Diagbox is too old for the newer 2008 software, if this is correct can you tell me which Lexie/Diagbox and software I now need and if possible...

Hello.

I´m back...

The C5 still runs, but the antipollution fault is now a regular visitor of my dashboard screen.

So far, it has been in the dealer's office three times for the same OBD Code. P0411, secondary air pump.

Now it has new spark plugs, new lambda sensors (both, pre and post-catalytic converter), and even I change the ignition...

Hi guy's need a bit of help, just bought diagbox v7.57 how do I find the installation password for set up thanks

Long story re above but what does it mean ?

From Diagbox

Camshaft sensor p2686 - supply of sensors 5volts no 3 wire.

I have checked the continuity of wiring from sensor plug to ECU all okay.

Looking for info

Kenny

Could someone tell me the Air gap on the rear abs sensors on my Peugeot 206 1.6 petrol Hatchback 2004 LHD please.
Thanks
benpv

Hi all, I am new to the forum and i'm very happy to have stumbled across the forum whilst surfing the web for an answer haha

I have a 2014 308 1.6hdi 115 with a intermittent injector fault which reared it's head a few weeks ago. After having the fault cleared and booting the car home i only seem to get little cough's now and again but still feel...

Some time ago I was going through Lexia and I thought I saw somewhere option to set the rain-sensing wiper option to classic intermittent wiping, but now I cannot find that option.
Does this option even exist, or was it just my imagination? :-s

Auto mode is practically useless (probably something to do with the sensor, but I don't plan to touch...

So I replaced the timing chain on my 2013 DS5 1.6thp, as far as I know I followed all correct procedures. Initially it was cranking but not firing, so I started troubleshooting that. After swapping in some coils from my BMW it fired up and was running very well (much better than previously when it was rattling etc), but the same pesky code that...

Does anyone know if and how we can connect to the PSA servers for a one off fee in order to download ECU software or updates.I thought this used to be possible but have been told that you now have to hold a permanent account in order to do this.

After trying unsuccessfully to talk to my X7 for several days with the Actia cable I bought 10 years ago, it seems to be a no-go as I don't have the full chip version.

ACTIA_Version_Screenshot.jpg

UmcJjVrbSbKCmkJ3y2jhNg_thumb_2799.jpg

79QtkyhPR2ePx4zMnCy6rA_thumb_2797.jpg

IMG_5271.jpg

So the question is: send it away to be updated or...

I'm looking into getting one myself, but there are so many versions, what do you choose? Some are listed as full chip, others lite. I take it there's a bunch of fake ones too. What do you pay attention to?

And secondly, is there any tutorial on how to set it all up on a laptop once you actually get it? I take it installing Diagbox is all it needs?

The engine management light recently came on, on my 2007 C8 with the 2.0 HDI 136 engine. It went into limp mode, switched on and off and then it performed as normal again. I borrowed a CAN OBD2 code reader which gave P1351, P2408, P0489. I reset it to see which warnings came back. It came back a day later and I reset it again. A week or so later...

Hello, Im new to the forum so please forgive if I break any etiquette

I have a Grand C4 Picasso, Petrol 1.2l PureTech Auto, 2017. Which, as I understand it, is a reasonable rare combination of engine/gearbox/car. However I hope that as the forum covers Peugeot cars to which also have PureTech engines this will help input.
Recently the engine...

Hi Everyone,

I recently got the following error on my ds4 2011 2.0 hdi:
P0125 - insufficient coolant temperature for closed loop fuel control,
I replaced the thermostat with the housing and the temperature sensor and still get this error.

Does anyone know what it can be?

Thank you!

Hi. I have been a follower of this forum for a while now and I have taken the plunge and joined up. My car, a Peugeot 3008 Hybrid4 2013, has had a problem with the service (12v) battery running down. It started 3 months ago and the faults that occurred were Air bag/pretensioner dash light came on followed by the amber engine repair required dash...

Citroen C4 Picasso 2007 Diesel Semi Auto Gearbox 1.6

2 Years and 4000 miles ago Citroën Wimbledon changed Clutch kit, DM Flywheel and slave cylinder.

Please help! I have a Citroen C4 Picasso 2007 Diesel Semi Auto with Gearbox related issues. The Clutch kit was replaced 4000 miles ago. A few weeks back Gearbox Faulty message kept on coming on the...

I had previously replied to a thread that described the temperature gauge reading rapidly dropping on a C5. My DS5 did the same thing sometime after a thermostat replacement. Turns out coolant was leaking from the bleeder screw, that I had stupidly over-tightened. I eventually fixed this by using the old screw but transferring the new O-ring to...

Hi all, I have a 2011 C3 picasso and i ran out of dpf additive , which to be honest I didn't know a dpd was fitted to the car, and now I have the service light on telling me the p filter add level low. I have topped up the additive but still the pight stays on. Any ideas how to get the light reset or is it a trip to the dealer.

Hi all, I posted on this forum last year about my car ,lumpy running,well this has been an ongoing thing,been all round the houses with different fault codes showing,have been working my way through the codes short story long,the latest code,(in a long list} is p0170,what is happening is on live fuel trim data in open loop,start sits at 0.8%then...

Hi all,

Firstly sorry for a new post, I've had a look through the diagnostic section and used the search but not able to reach a conclusion myself - if there's a good particular discussion to point me at instead then please do!

I'm looking to create myself Diagbox capability.

Will buy a laptop to dedicate to the job. I've seen old Panasonic...

Hi. I have a 2004 Peugeot 206 1.4 with an automatic gearbox fault. I would like to scan the car using the Peugeot tool. My question is should I install Diagbox or Planet Peugeot? And what Windows operating system should I use? Thanks for any information \:D/

Hi guys my Renault traffic 2016 diesel keeps turning off as soon as I start it.
When it first started I notice smoking coming from steering wheel gap.
Call road assistance and they said ignition switch. Mechanic checked but said something needed re soldering worked for 1 day then started Doing it again.
Key was then changed then worked for 2 days...

How do I tell my Peugeot 3008hdi that a new dpf has been fitted. I have diagbox v7. 57.i have cleared all the faults but it keeps coming up dpf worn. If I look in the parameter it says that a new one was fitted 88,000kms and has o kms left and is the only thing left that I can see to reset. Thanks

Does anyone know anything about these?

Peter

help

ive got a xsara picasso 07 1.6 16v and its got some serious problens

runs from cold for aprox 30 mins then kangaroos and then acts like its out of fuel. switch off re start and works for 20/30 mins

its had map lambda temp injectors

error p2191 error

just fitted a new fuel pump relay and the car went nuts...

i had keys in my pocket...