French Car Forum

Anyone know if all front hubs are the same across the range??

Mine started to have a fair bit of a play in it now and killed the second wheel bearing in as many months.

207 110 1.6 hdi

👍

Hi as per title, looking for info on part numbers or equivalent for replacement springs for my 407 coupe, which is a 2006 with the 2.7v6 HDi engine. I don't have the vin number handy, but I'd hope this gives us enough to get the springs parts numbers? Thanks in advance :-)

Hi yhere guys ,i just got a 3008 decent year and millage ,my whife loves it ,the only thing is got it from an acction site ,and it has i belive parts missing ,if anyone knows what they are?i would like to take the caf down to dealership but it dosent start and stack in P ,was a nightmare to take it off ,i dont know how they put it on in the first...

Can anybody tell me the size of the rear hub nut please
changing rear discs
partner 2014 1.6 hdi
many thanks

Tried a few things from my previous posts with regards to smokey exhaust under load.
1. new egr valve
2. air intake complete clean out, intercooler, throttle body, egr pipe, intake manifold, all full of crap.
3. replacement map sensor
4. replacement maf sensor
5. new pcv valve diaphragm and springs
6. injectors still to be removed and...

Hi

Does anyone have a clue as to the OE part number of hose connecet to the marked part in the picture?

Thx

Hello

I recently purchased as 407 sw 2.0 hdi, it’s covered only 146k miles since 2010 when it’s life began.

I know the service book says the belt isn’t due to be changed until 140k. But I’m trying to find out if it’s already been done.

Could someone more in the know look at these pictures to see what they think.

I’m thinking it may have...

Hello, my wife has a 2008 1.6 e-hdi 115 2014, it has been smoking on acceleration since it was purchased last year, on renewal of the mot it failed on smoke from exhaust with particulate filter fitted plus the emissions are on the high side, a few things have been looked out without any change, today i checked the fuel injectors fitted they are...

Can anyone point me in the direction of a wiring diagram for a 1.4 8v 206s VIN VF3**************[VIN obfuscated, can be read by forum staff] The only ones I can find online cover Bosch and Magneti Marelli ECUs but I'm not convinced that's what I've got. I can't see any manufacturers marks on the ECU just two PSA stickers. Both BSI and BSM are from Siemens. I've even scoured the local...

Cannot turn off engine fault codes: U0118 P1434 P1435, adblue is filled in. Could it have Eolys also?

Hi. I have a 2.0 HDI 5 speed manual gearbox in my 2004 motorhome. The speedo sensor has leaked oil badly so I am fitting a new one. I can't find out how much oil to put in when I refill. I read 1.85 or 2.1 litres from different sources but I don't want to put too much or too little.

Oil specification would help and if anyone can advise the best...

Hi again again fcf...

Pug 306 2l hdi estate 1999/2000 phase 3.

The cabin fuse box ( and the under bonnet cooling system heater plugs relay/fuse box ) has a few green relays that seem to run hot to me.

Are these green relays all the same please ?

Which relays in the cabin fuse box control the windscreen wipers and wash wipe function please...

Hi folks. As in title. I'm struggling to find any info on how to drain the system. I'm going to remove the EGR today but it has a Cooler built in.

I notice there is possibly a drain plug at the very bottom of the pipework made of a plastic hex nut type. Assuming that is it but looking for clarification.

Thanks people.

I've googled like crazy to find the specs for the Peugeot 807 cargo but can't find anything.

Anyone know how long and wide items the cargo can hold if all the all the rear chairs are removed?

Good day everyone

I am looking at replacing the rear axle on my VF3**************[VIN obfuscated, can be read by forum staff] PARTNER VU (M59) SHORT VAN '600' 1.9 D 71 (DW8B)

Is there a difference between the Peugeot '800' axle and the '600' axle. In other words, will either fit with no modifications?

I am hopeful that somoene has some experience with this and can assist.

Cheers!!

Bought an '07 2.0 HDI about 6 months ago, it has been really good no problems. Last Friday whilst driving it just cut out. Completely. No lights on dash, all out. Turned ignition off and on again, normal dash lights on again but would not start. left it for 2-3 mins, tried again and it started. Managed to turn around, got about 1/2 mile and it did...

Am gearing up for some pretty serious works to my 405 Diesel Estate (na), which will include:-

Replacement engine
Replacement Gearbox
Replacement Clutch Kit
Removal of remainder of AC equipment
Investigation of possible slight buckling to OSF Inner Wing following an accident about 5 years ago
Investigation to structure, particularly difficult...

Hi, folks. I'm struggling to find a drawing of the vacuum solenoid locations and connected pipes etc. I'd ideally like one looking from the rear as I have the Peugeot Worksheet pics already.

Hope you can help me out. Thanks

Hello,
I have an very serious issue with my Peugeot 307 2001 2.0HDI engine code: RHY.
I have been living with this issue for more than 10 years but it happened only 1-2 per year.
The printed curcuit of the ingnition key was changed in the beginning of this year by an official Peugeot service and the issue appears very often but radomly, for...

So, I have degreased and washed down my 407 V6 engine lots of times in the past with no issues but this time things went a little bit wrong.

Engine was cold, sprayed degreaser to get rid of some oil leaks in the front, washed it down and went away for 5 minutes.

Came back and noticed some smoke and the start of a fire.

Quickly disconnected the...

Yesterday 307 ran like a teenager not wanting to get out of bed.
Then the anti pollutant fault with engine check light came on
So i stopped popped the bonnet saw the plug to maf wasn't on properly pushed it back home everything fine , however the driver door won't unlock this is the second time its done this always the following day this happens ,...

Hello all,

Newb's first post here. Bit of background: My wife has a 2011 Peugeot 3008 1.6 Hdi sport. Has been having recurring error with Risk of Particle filter cogging . Had it brought to a reputable independent who ran diagnostics. Said DPF system was OK - issue was that 3 of 4 injectors were failing - poor combustion then leading to particle...

My friend and I are almost finished restoring one of our 407SW 3.0, we bought the vehicle 2nd had awhile ago and the rear parking sensor did not work; the reason it does not work is because Proxia/Lexia shows that there is a trailer hooked up to the vehicle but there is not. We have also installed a different BSI and radar control unit and...

Hi everyone
I am having trouble finding a decent haynes manual for a 205 diesel - i can only find manuals for petrol. But specifically i want to find out the location of the exhaust gas recirculation valve - if it has one - and how to remove and clean it
any help appreciated

Hi all,

After some advice, I have a 2 ltr 2010 407sw and I have a ac issue I need to rectify.

The basics.
The car has been degassed and hold pressure with no leaks.
If I turn the ac on the compressor will click in and run for about 10 seconds and cuts out, the fan also clicks in and runs on after the compressor has disengaged but again stops...

Hi All,

I recently purchased a 2.0 hdi 150 exclusive as a non runner due to injector issues.

I have managed to sort those issues but I have another I cannot fathom

The Electric Parking Brake!

Garage I bought car from cut the o/s/r cable to release the brake and enable the car to be rolled.

I have a snap on and when I started on the job I...

Hi all.
After a long while looking I decided to jump in with both feet :-) :-D

Any mechanically minded people on here that can assist me please.
I recently purchased a 10 plate 3008 2.0 hdi 150 that had been sat 2 years in a garage due to Injector issues .
When it arrived one injector (No.1) had been removed. So I bought an injector, injector...

:roll:

Just did an oil change on the 206cc ive used a flush in a warmed up engine which i let run for 10 mins as what the can said ,then drained it all out, i let it be went inside had my dinner then back out pop the new filter in do sump nut back up have a clean up the refill with oil . Now i filled my jug to under 4 litres so now im in panic...

I have a 2015 Pug 308 GT 180. It has new injectors, recon turbo etc & was running brilliantly.

I took it to a local garage for a cambelt & water pump change, due on mileage.

When returned it put on the EML with cam/crank syncro errors & would not start when hot. Garage were reticent but looked & say they have changed nothing but now it runs....

Hi guys spelling not the best but here goes.

I have a fault on my car after a pulled a fuse fuse out i was looking to see if the aircon fuse had gone but it was ok. After putting it back in a fault came up and saying engine fault get repaired.

The only thing that has stopped working is the stop and start.

I have been with the auto electrician...

Hi All, This problem started a couple of months ago as an intermittent resettable Limp mode problem and now is a hard fault. The fault codes I have had were:
P1062: VVL lift system fault.
P1067: VVL lift system motor/ short circuit/ open circuit.
P1015: VVL system fault.
P010D: VVL lift motor control open circuit
P1014: VVL position sensor track 2...

5 30 is mentioned once in service history
Seller said he uses 10 40 .. now im confused..

Any recommendations

#-o

Any ideas as to why i can't get my steering wheel ignition lock to come off can't turn the key ,nothing.

Was hot today could it be the reason its stuck on ?

On an 07

How's it done as I can't find anything online as it's all for the hdi.

Sorry about photo quality it was in very bright sunlight.
I have a suspicion this bodge fix by a former keeper of the car might be giving the 307 some running , bit long to turn over a bit lumpy for few seconds when started and I've had the anti pollutant fault up on dash it was a hot day so i think this fix may of loosen & let more air into the...

Hey guys i have 508 1.6 ehdi 82kw with EGS6 automatic gearbox, mechanics at my city replaced last year gearbox oil but they put in total ATF fluid in it.... As i can tell by searching oil for this gearbox is Total Gear8, also they put in total DA fluid for servo and again as i found out right one is total D/G3, im loosing servo oil but there is no...

I have a 1997 Peugeot Expert 1.9D (camper sefl-conversion) with a 1994 Xantia TD dropped in.
It's still a very reliable (if smoky and ancient) machine.
However last 2 years I've noticed that it overheats if you get stopped on the motorway on a hot day. The gauge gets over 100C and the coolant tank cap tends to let off a bit of overpressure so it...

Hello everyone. Peugeot 407SW 2.0 Diesel 2009. Starts first time every time, drives faultlessly 99% of the time but recently (last month) I have experienced an intermittent 'momentary hesitation' similar to fuel starvation. The car 'jolts' once or twice but then carries on perfectly well. This scenario might occur once in a week or so. It is...

Hello,

Has anyone removed the actual rear floor of a Peugeot Partner commercial van?

I have water damage in the area that would usually be the footwell in the 4 seater passenger version.

When looking under the vehicle on the lift at the garage, the rust is pretty bad and it will not pass the next inspection.

I am hoping that I can remove the...

Vehicle details:
Peugeot Partner Combi Mk1, 2001, 1.9d WJY
Vehicle background:
Bought in November, working but leaking head gasket, drove fine but needed coolant topping up regularly. 190K+ miles though 70K in the last three years which could indicate replacement BSI/instrument cluster previously. Found the coolant level sensor gunked up and...

hi there.
what is the xu92c engine crankshaft code? (like 0501.G1)
i cant find it in catalogue

HI, I have a 2010 Peugeot 3008 1.6 diesel semi automatic, my problem is that the car shudders when moving off, can anyone advise please TYIA.

Hi,

I need an advice,

timing belt snapped in my 03 expert 1.9 no turbo,
I took the head off and crankshaft was snapped half,
decided to replace the engine,
bought one off ebay but I haven't checked properly and I got one with different injection pump,
I wanted to replace the pump with one from the old engine but then I found out the pump was...

Marc, the diagram of the door lock mechanism & handle for ,my 307sw a bit above ,would it be possible that the little lever on the handle or mechanism could possible be slightly miss shaped and causing the opening of the catch to not do as it should ? If a slight tweak to either part is possible do you think it would make the handle open the door...

I have a Peugeot 508 which has error P2032. It says short circuit to earth. Is the sensor faulty? I've looked at the temp readings and the sensor seems to work properly.
Do someone know what the prerequisites are for this error to pop up?

IMG_20220623_204038.jpg

:oops:
Start with a red face moment , I was driving home earlier with my beautiful wife , honest she is. When a motorcyclist over took us & started making hand gestures. Right i thought i aint having no of that so opened up the turbo on the little 2 seater whoosh, that was my hair flying off .. then i thought hold on might be something up with...

Hi to all

I have peugeot boxer 2.2 hdi 2007 diy camper van. Weight of van is around 3000kg. Total driven 160.000km.
I have problems with black smoke out of exhaust.
When I prees throttle to midle or more it start to smoke. Smoke is black. Above 1800rpm it produces more smoke then at lowr rpm. If I'm gently with throttle there is no smoke at all....

Hello all, wondering if anyone has a dog guard fitted to their 208/2008 that could shed some light on the fitting? Managed to get hold of one but came with no fitting details, how I thought it would fit doesn't tally with the he's in the frame! 🤪I've been on a Google mission but can only seem to find generic dog guards! :?
1606644580 part number...

I have a 91 year old Neighbour who has a 2006, Peugeot 206 where the dot matrix display went back to 01/01/2000 in Spanish!! It only goes to the papershop every day so does not really get a run. However, I think the batery may be cuasing the problems, as its 5+ yeras old.
I have put my little LED tester on it and battery & charging system look...

Hi I have a y reg boxer, 2001 1.9td . Looking for a part for my gear box but not having much luck. Looking for the gear box cover(rear cover/casing)but can't find one anywhere. Mine is very rusted and flaky and appears to be leaking(maybe) defo have a leak fyom somewhere i suspect gear box as bottom is oily but so is above further up.Any...