French Car Forum

Hi I have a 2009 207 1.6hdi sw that needs 2 new handbrake cables which I have released from the handbrake end and the calliper end but can’t seem to remove the cables from the inside even after pulling them quite hard so have I missed something

I brought my 307cc from an independent dealer in London, price had been reduced several times as dealer took it in PX. He doesn't usually sell diesel cars due to the LEZ and ULEZ charges making them difficult to sell. Car was to be sold with new MOT but failed on emissions, their mechanic eventually got it to pass after several attempts. Dealer...

Hi,

Is this the correct spring for my car which is a...

Peugeot 306 2001 HDI meridian
Engine Size 1997cc
Cylinders 4
Valves 8
Fuel Type Diesel
Transmission Manual
Gearbox 5 Speed
Drivetrain Front wheel drive

thanks

Does anyone know if there's any sensitivity settings for automatic wipers on 2014 peugeot 208?
I haven't been able to find anything. Searched in all ECUs I could think of.
Do these settings even exist? Wipers are driving me mad and worst part is I can't use single swipe either because peugeot foolishly decided to remove that function from...

Hello guys , i need a wiring diagram for front washers for 2008 2018 asap please help.
VF3**************[VIN obfuscated, can be read by forum staff]
Reg kr18sxd

Hi
Got me a new problem now, after fixing the NG4 Nav unit with a new DVD drive all worked fine, until Tuesday last week, started up in morning and ping... EML on ? So drive to work anyway but no limp mode at all drive really well, on parking at work I noticed the front parks activated and put up image of car car on pop-up screen, but no distance...

Hi, I have twice filled the tank to near full and each time there has been diesel leaking afterwards , seemingly near the top. However my mechanics cannot find the source but will change the seal on the sender unit as a 1st step though it’s not apparent to be coming from it. Anyone experienced this before?. We’d much appreciate any pointer....

So I got my daughter a 2011 308 1,6hdi, the 112hp version.

It is running maybe a little rough, slight hesitation on throttle, possibly a little thristy. At first I thought maybe an injector was bad then I checked the fault codes and it shows P1382. My googlefu says that is for the VVT solenoid. Am I right or wrong? Second question is where is it...

I've been noticing the 407 is gradually using more fuel. A couple of years ago on a long trip to the UK and back at 70-75 mph on motorways it gave me 53 mpg. Just done a 450 mile run at the same speeds yesterday, again on the motorway and it's doing 42 mpg. Last time it went to the MOT the tester said the emissions were unstable but it passed....

Peugeot 205 xud 7
I have to check out the alternator system , trying to locate the alternator fuse , just where is the fuse , in the fuse tray or engine bay ?
Battery is very low , when i removed the positive terminal from the battery and engine running the engine cut out so seems like the alternator is duff or blown fuse .
Can anyone help please.

Hello,

I have a Peugeot 308 with some transmission problems. Its the manual gearbox that they call Automatic :rofl2:
The faultcodes is P1755 wich I understand is the clutch actuator position.
Could a reset with a computer work? Can you use Lexia software you get of ebay to reset the position?
Is it very likely that the clutch and flywheel needs...

Just bought a 2012 Peugeot 308 1.6 hdi, previous owner said the car was still running but the cam wheel is rubbing against the side of the engine mount, is there a common problem that would cause this on these engines? Thanks.

Hi all. The linkage in my front window wipers has broken. I’ve spoken to Peugeot parts and they say my only option is to buy the full wiper motor for £380; all I need is the linkage arm. Would anyone have any suggestions on how to get my hands on this part alone? Thanks in advance.

Hi Folks,

Air bag lights are an MOT fail this year. I had 'P611 - Right Front Satellite' on DiagBox.

After a lot of messing around this turned out to be the small green thing behind the Seat Belt Tensioner - ~£80 from the Dealer - and an easy fix.

Just to let you know ........, Ian

Hello,

I have a 2009 308 SW. Engine warning light came on so I took the car to the garage. They have advised it needs new DPF and propbably a new turbo which probably wouldn't be economical given the age of the car.

Just interested in what other people think and if anyone can recommend a good peugeot specialist that could give me their opinion...

Hi folks,

I have a 2011 508 GT 2.2HDI and for the past few days not been feeling the GT factor, it feels if though the car is restricted. There are no warning lights and the car runs fine otherwise.

I have scanned the Engine ECU with Daigbox and found the P0299 Turbocharger pressure regulation fault .

Fault code details:
Atmospheric Pressure is...

Hi all,
Hoping someone super knowledgeable here can help me. I've tried various forums but no luck so far.
I have 2014 peugeot 208 Roland Garros 1.2vti. Car is very well equipped but missing hill assist.
I've tried coding it using diagbox v7.57 as that's last known version for offline telecoding but no joy. It fails every time. I was looking...

:-D
Hello all.

I need to know some stuff regarding a 207 1.4hdi
What to look out for , wheel bearings suspension stuff oh and where is the diesel additive bag located and how do you change it, many thanks . Oh .. would you buy one ? But the most important thing is about the additive bag location

this car comes up with no comunication with the ABS/EPS ECU on Planet 2000,

is says ABS BRAKE FAULT on the display and several warning lamps are on also the speedo does not work

one fault code is P0500 relating to a speed sensor, but if the ABS ecu is not communicating, i would think the speed sensors are out of action,

according to the hand...

Hello,

My 2010 Peugeot 5008 1.6 156 has a couple fault codes. Could I get descriptors on these codes?

BSI: F303
Gearbox: U1208
Engine: P15A6 P15A0 P2262 P0299 P0087 P0172 P0945 P0262 P1337

All of these fault codes appear after having cleared all the fault codes a couple days earlier in Diagbox. The last two engine fault codes about injector...

Hi all,

I come from Taiwan
Found this forum while looking for a solution to my problem
There are very professional and friendly partners here

My car's VIN is VF3**************[VIN obfuscated, can be read by forum staff].

I have experienced error codes P12A5, P11AA, P0409, P0488, and P0490.
I have replaced the second cylinder fuel injector and cleared the error codes.
P12A5 continues...

Hello all

I bought shifters paddle for my Peugeot 207, they are already mounted and connected but still doesn't work. The car is prewired with this features.

Can you provide me please the wiring diagram for this paddle shifters or any support in order to fix this personal issue.

Or, is mandatory to activate this option in Ecu/BSi?

Thank you in...

I'm working on a 308 hdi 90. When I came to change the timing belt, it's a bit difficult. Because the engine is a 9HY 110 originally, and the flywheel has been swapped for the non DMF 90 one, there is no guarantee that the locking hole in the flywheel is in the right place. The flywheel isn't keyed to the crank.

Are there any other marks to use...

bought car as having eat6 auto gearbox, but according to my handbook its a Porsche tiptronic 6 speed gearbox, now I think Volvo and Saab have same gear gearbox and they say they have to have oil changed at 60,000 miles, so mine has done 69,500 mile so do I have to have mine done also as I don't want it going pear shaped in the future.regards James

Hi my wipers keep stopping in the upright position.
Is there a way to reset them

Hi All
Not having much luck finding an answer to this :-(
I have a 2013 Peugeot 208 1.4 HDI ( Access ) I think
The steering wheel has no radio controls they are on a stalk under the wheel
I have bought a new Dynavin head unit but the stalk controls do not work on this so I was wondering if I could replace the steering wheel with one from a...

Hello guys,

Car is 508 2.0 163 HP 2011 year. Check engine light appeared some days ago, after accelerating a little bit. Scanned the car and got code for O2 sensor ageing. P2297 and P0134. I wanted to change sensor by myself, got the tools and everything. Followed procedure from document, but i am unable to reach sensor with any wrench as the...

So sorry to keep posting but there must be someone that has some info on this.

I'm going to start with the most obvious clue.

Low power/boost/speed potentially linked to: Intermittent No Pedal Response for maybe half a second then a thump and it goes. No engine light for 6k miles. Starts every time, but it's slow. Turbo works especially at slow...

Hi. My turbo oil feed pipe needs replacing but I can't find a step-by-step guide on how to remove/replace it. Can anyone help? I have bought a new replacement for it.

Screenshot_20230307-190343.png

My brother has had a 207 GTi for over a year now and has had silly little problems with it. The high pressure fuel pump on the end of the camshaft packed in causing it to barely run, then the other day it started to choke at higher RPM which turned out to be the cat blocking up and choking the car.

It's always felt a little flat and has never...

Morning all,

Going to set to with this job, this post will get pictures added later, I'll take snaps as go along and add them in later.

So, wet carpet on passenger side, slight sweet smelling a touch sticky between the fingers = coolant.

Matrix replacement isn't full dashboard removal task thank goodness. So I'm guided by a video Huskyxantia...

Hi. Though some of your contributors might ben interested in the following situation I have recently experienced with my third Peugeot, this time a 2016 petrol 2008 1.2 Allure S/S that I bought nearly new from a Peugeot main dealer in Salisbury. For the first couple of years of my ownership, I was working and commuting 50 miles each way to work,...

Hi

I've managed to mangle the brittle connectors to my alternator ( 96 571 296 80 bosch 180 Amp) and air cond compressor (9800849780 SD7C16).

Is there a wiring diagram / harness loom pics that show which wires go where and wire colours (just in case) plus any relays / fuses (if any)

regards

Hi guys,

I have an issue I changed my sat-nav and now my radio is beeping every 5 seconds, now I know I need to re code it. I was wondering if anybody that’s around Kent would be willing to help , I tried to contact JGRA1 as I saw he’s pretty close in Edenbridge , but I can’t actually contact him as I don’t see the message button at all when I go...

Hello,
On my way home from work today my Peugeot 2008 1.6HDI starting kicking out a lot of white smoke.
This was worse when accelerating.
I did have a message about DPF filter possibly being blocked flash on the dash for a split second. Not really long enough to take in exactly what it said.
Since being home I have plugged in my OBD2 reader but no...

I have been trying to fix an ongoing issue for a while but I am not winning. The car is a 2009 308 with the 110hp 1.6 HDi engine. We have a tiny oil leak at the air outlet pipe from the turbo and from the intercooler pipes at the air doser. I changed the outlet pipe and cleaned and reseated the intercooler pipes but the problem persisted, a week...

Hello to all, I am having this issue sinc I retourned from a 400 km trip. The no coolant indicator appears in the dashboard and when I opened the hood up, I saw the coolant expansion tank completely black on oil. Once on my home, started to try diagnosing the problem. I replaced the oil cooler o rings and started to clean the coolant system with...

Im wanting to purchase a new remote central locking key then program it with pp200, i haven't the key card to the vehicle and understand there are two codes one for the chip one for the key . Would i need to go to the main dealer with proof the car is mine e.g logbook,driver licence to get said both codes or is there another way ?

My car has a fault - Engine Fault: Repair Needed

The car purchased recently from a large car supermarket.

First time fault came up they told me to take to Kwik Fit who cleared the faults.

A month later the fault has come back and they have advised that I can take to a better local garage or Peogeot dealer to get a proper diagnostics which they...

Hello everyone

I have a problem with remote unlocking.
1. I paired the key
2. when I click the unlock or lock button, I only hear the relay clicking but nothing happens, the car does not respond.
PEUGEOT 307 2.0 HDI 2001
can you help me ?

Had a new 3 piece clutch fitted to my 14 plate 1.6hdi partner van, Simply because it was worn, Also had a clicking when the clutch pedal used every now and again which after diagnosis was the slave on the outside of the box.
No duel mass so happy at that, Had the clutch and slave changed and got it back and advised a vibration at the biting point...

Hello again everyone,
Just a quicky regarding the water pumps fitted to the 1.6 and 1.4 HDi engines, can the pumps be interchanged between engines?
I've got a brand new 1.4 version that i'm hoping to fit onto a 1.6 dv that needs a cambelt change.
Anyone clued up?
Cheers.

Hi!I have cutting out issues,7 months passed and the problem is still there.Replaced egr,iat sensor,fuel filter.The engine will cut out at traffic lights,junctions,sometimes while driving.P1113 and P0087 are the error codes that are related to fuel pressure.Someone told me could be the fuel pressure sensor or leaking injectors!Any advice?Thanks!

Hi,

Couldn't find the data anywhere - does anyone have the capacity of the hydraulic fluid (LDS, power steering) for a Peugeot 508 1.6 THP 156BHP ? Is it more than 1L ?

Thx

I get the error message of P0234, from a youtube video, mentioned the Turbo pressure sensor / MAP sensor needs to be cleaned. Unfortunately, the structure of the peugeot 1.6 hdi engine on the video is different with mine.
Could anyone tell me where is the location of the MAP sensor for my type of engine,

More less, the engine looks like the one...

A few years ago I ran a 407 Coupé GT with the 2.7 v6 hdi - and it was an enjoyable car, so I simply had to watch the JayEmm review of the model, albeit a 2.2 petrol manual SE he reviews, so I thought it'd be interesting for y'all peugeot fans to see his opinion of the car in the following video:

Apologies Peugeot enthusiasts. No slick advertising presentation of a Peugeot classic vehicle in a minute-long video clip. No something much more meaty to get your teeth into. Its a film...yes that's a film....you can tell with the crackles, the floaters and the poor picture quality. Added to that...it is in French from start to finish, and it...

Hi, our company recently purchased a Peugeot partner 67 plate 1.6 blue hdi at 100k miles. I have been researching and wanted to avoid the 16 valve iteration. I would be grateful of any advice regarding preventative maintenance tips and recommendations. I have read a few stories of the adblue tank needing replacement at great cost but this seems to...

Hi all. This is my first time posting due to a problem with my Teepee.

Bought the car second hand in France from a Peugeot dealer. It has around 120,000km on the clock.
Last week, on our way to holiday, it died on the highway at 120kph. Death rattle and coasted to the hard shoulder. It had been running perfectly smoothly, no noises, or problems...

I've just pulled the injectors from a replacement engine, three came out with minor persuassion, and one was really tight and came out with the sleeve.

I had to abuse it and then use a mildly modified 2 litre HDi puller set that I had in the garage. The sleeve is well and truly stuck onto the injector with carbon buildup, and I ran out of time....