French Car Forum

Hi thanks again for help with the electric door mirror fixed
Still got the problem with central locking not working
Fault none of the doors lock no faults set, looking in parameters on diag tool key is recognised shows doors lock ( but they do not move)
I can actuate the rear hatch and the hatch will open but doors do not
Checked the doors were...

Hi all i have another problem with the 3008 driving home and got a warning message saying particle filter additive level too low repair needed?

I have got one of those ebay scantool boxes with software WOW so i plugged it in to see if it does resetting of the additive system to see if i could do the job my self any way i went through the...

Does anyone know how much torque on the waterpump bolts?

I did 20Nm seems a bit low

Its a Cast iron block not the aluminium one.

Greetings from Cornwall Help!!! Does anyone have a wiring diagram for a Mk1 Expert 1.9D or even better a manual for one. I cannot source a Haynes Manual. And some offerings on EBay are beyond me to download - simple PDF is fine but some of the things on there are beyond my 75 years!
Jon

HI, my wifes 3008, the ABS light is on. took it to the local garage who said the ABS switch has ruined the wheel bearing !!!! is this possible? cheers Terry.

Hi I've got a 2014 508gt 2.2 HDi. I have had diagbox connected up and it's got B1836 fault code transponder aerial fault permanent. Can anyone help me solve this problem many thanks Dave.

Hi have problem with Peugeot 3008 2016 drivers door mirror and central locking not working
no fault codes present.
1 does it have a door module to work mirror and lock,
2The electric window works
3If I could get some help as to how they are operated and a wiring diagram would be great help
Vin No is VF3**************[VIN obfuscated, can be read by forum staff]
Thanks Joe

Hi, I´m looking for wiring diagram license plate number. Cable at door is ok.
Peugeot Boxer III 2.2 hdi 2011
VF3**************[VIN obfuscated, can be read by forum staff]

thank you

What do people recommend to use as a gasket sealer for a Peugeot sump? The stuff that came off was a white sealer type of stuff with no traditional cork or rubber gasket. I have read that people seem to use RTV but can not work out if the different colours have different properties or even if I need RTV and a simple 'instant gasket' stuff will do...

Greetings!

I have a 508 SW 2013 with 2.0HDi engine RHF (DW10BTED4)

When I changed my timing belt at Peugeot official workshop here in Sweden they said I had an error code … so I asked what it said and they said Fan Low Speed not working. So I asked him what it meant and he said that it basically just means that the fan doesn’t work on low...

Help, my 207CC keeps cutting out 30 secs after starting.
Its at the garage and hes stumped.
Hes changed the cam sensor and vvt valve sensor but he seems to think its something to do with the VVT.
Would taking it to a Peugeot dealer help, ie would they have better diagnostic kit?

A few days ago when driving the V6 2.9 I saw a bit of steam and decided to stop and have a look under the bonnet.

I found the water level sensor twisted a bit and when I tried to move it back, it came off and coolant sprayed every where.

It seems the lock in clips on the sensor had perished after 18 or so years and had caused the sensor to...

Does anyone know the tightening torque for the drain plug on an MLUC gearbox on a 2007 Peugeot Boxer 2198cc?

Hello, we have a 2010 Peugeot Boxer converted by Autocruise into a camper van, the issue we have is the alarm siren, I did note the previous post on this but no conclusion, ours is the same issue, turn on ignition and yellow alarm symbol stays on, start the engine and the main waning key and lock is illuminated and a message , the alarm system is...

Does anyone know the tightening torque for the gearbox drain plug. It is an MLUC box and I am assuming 30 Nm but haven't found any confirmation. Thanks

Hi,

My Peugeot 807 has been fine, until today when it just spluttered to a stop, and now rev's OK but does not drive at all, it has no power in the engine. To the extent that I cannot drive the car from where I have managed to park it on the street.

I have plugged in a simple OBD2 reader, and it gave me the following error codes P0299 and P1351...

Today i was going to replace the MAF on my 90hp 307 but after i took the old one off i found what i think is excessive oil in the pipe, i must confess i don't know when i last checked it & someone else fitted this particular MAF meter so it hasn't been cleaned out recently and i know some oil is normal but i think this is too much. My thoughts are...

Hello, this is my first post. I write from Spain. Last weekend the alternator belt of my Peugeot 505 GTDT broke and went missing. To put a new one do I need to remove all the other belts that are in the way and/or removing the radiator? I'm thinking of changing all the auxiliary belts. Thanks in advance.

Hope someone can help me with my ( now ) non starting issue :roll:

I bought my 2008 approx 6 weeks ago as a Cat S ( tailgate and minor floor damage ). Since then, it's been stood on the drive and started every week or so to move it but it has not idled for longer than a few minutes. It was delivered to me with the fuel indicator pretty much in...

Hi all, if someone could maybe give me some recomendations what to check

I have 2005 peugeot 407sw, i bought it 2 years ago and climate control was not working whole time, now i got Diagbox and i checked today status of sensors etc, ataching picture....so it says all requests are inactive, but on driver and passanger request its fully cold, its...

So I've notice a bit of a dribble on the T piece at the joint that holds the thermostat sensor and distributes the water around the engine.

dribble 1351KT T peice.JPG

The part 1351KT seems like it is only sold is a complete hose set, although I only need the T piece.
1351KT hose .jpg
Seems this is a known issue and will only get worse with...

Hi,
I have a Peugeot 307, year model 2006, with automatic gearbox AL4. I get the very common Gearbox faulty error after driving about 5 minutes, only when starting with cold engine. The gearbox then changes to limp mode (3rd gear).
If I stop the engine and start again, the problem is solved until next time.

I have made diagnostics, I get error...

Hello! I have a provlem with my Peugeot 207cc. Roof problem. Error code is 08A0 left hand side roof boot locking switch Signal fault. No signal. Any fix FOR this error ? Thanks a lot.

IMG_0016.jpeg

Hi all,

I’ve not been able to lock my Peugeot 406 for around a year now. Not a problem at home or at work, but it makes me very conscious when I am out and about! I’d like to get it fixed.

I have only ever had one working key with the car, which is the spare key. Until a year ago I used it to lock and unlock the car. It did come with a remote...

Hi All,

My 807 went to the great big car park in the sky after ingesting its turbo, so my other half has thrown the 308 SW car keys at me, (was my car before the 807) and told me I can have it back as she wants a mini....

So, I've just had it serviced, and the rear right brake caliper is sticking post new brake shoes and discs, could the hive...

Good evening
I am really struggling to locate a supplier of the 11 mm bolts for the Bosch callipers It looks like as widely discussed on here that Pug parts are not standard and what ever available was fitted

Many Thanks

Hi!

Long time lurker here :oops: Been using my best google kung-fu powers lately to find some info on the MCP-clutch, but can’t seem to find much other than a lot of less than positive critique of its operation :lol:

Recently my 508 1,6 e-hdi has started to get clutch slip while accelerating in higher gears. The car has done 210 000 km / 130...

Hi,

(Video link below for better understanding)
Is it the hole where you can block the flywheel? I am not sure because it is set up in a way I can't insert a drill, there is not enough space to insert it straight.

Maybe I need something curved or bent?
This is strange because on other vehicles with this engine (1.6 hdi) people just insert a...

Hello all I am working on a peugeot 5008 with a wheel sensor issue, I have changed the LH Rear wheel sensor as indicated in diagbox and fault still exists so looking for a wiring diagram and connector locations for a peugeot 5008 vin VF3**************[VIN obfuscated, can be read by forum staff] thanks 😊

Hi. Can someone tell me what these two units are called and what they do please? Also they look difficult to remove and as if they would break if touched by a heavy handed idiot such as myself.

20230516_115257 (1).jpg

Peugeot partner 1.6hdi 2006

I've removed the bracket at the back of the pump(4 bolts) and the nut and the bolt on the side/front however you look at it. So I'm sure I've removed all necessary bolts/nuts but it seems pretty solid in still, there's a very slight bit of movement in the pump but seems like it's still bolted in somewhere?

Any ideas?

Hi all hope someone can help trying to sort out a 207 1.4 petrol with no acceleration for a friend

Vin no VF3**************[VIN obfuscated, can be read by forum staff]

Need a wiring diagram for tps and app have used diabox to get codes p0221 and p0121

Using diagbox actuator test to check motorised butterfly valve result in no movement of butterfly valve.

Display shows pedal movement but...

My 407 2.7 Hdi has twin turbo's but Diag only shows one reading and all it says is Air Pressure at the intake measured by the turbo pressure sensor .

Some data / assumptions are

a) both turbo's feed into the inlet manifold
b) there is only one turbo pressure sensor (eg not one for each turbo)
c) at idle (672 rpm) there is no turbo boost and...

is there another beeled point on 308 HDI? theres one at the front of the engine by the gearbox, have bled that , it wont take any more coolant in but theres no heat coming from heater, it was fine before I changed the rad.

Hi!
Can anyone tell me if the cup that holds the strut on the top of a 307 should be a tight fit all the time. WhenI lower the car and the strut gets compressed the cup at the top actually comes away from the bodywork. Is this correct??? I have a 307SW 2.0Hdi 136, 2006 registration.
I changed springs and struts about three years ago. Didnt change...

Good morning everyone.
I've recently acquired P207. Still waiting for my XM (under never-ending restoration), but meanwhile I can use this little Peugeot as a second car. I know, that this is one of the best place to ask questions (and find the right answers), so I wold like to ask about two things:
1) Radio - I have empty space in the middle of...

Hi,
Anyone can recommend a place where I can order a new case for my key? This spring for the key is not working so the key is always out.
And can I transfer it myself to the new case or do I need to visit Peugeot to do it?

Few hours ago, I got message that something is wrong with the engine, connected Diagbox and got this P1434 96 error. I know is related to FAP additive pump. And my bad luck is that this happened just few days before my vacation trip, so I don't think I have enough time for repairs.

Anyone knows can I drive with this error? Will the car do the...

Hi all,
Newbie to diesels trying to change cam sensor on 3008 1.6hdi, possible fault flagged by code reader.
Damn thing is almost inaccessible. Is it safe to remove this pipe to improve access? WIN_20230621_13_04_43_Pro.jpg

Has anyone bought AliExpress keyless door handle and install them on your car?
What is the quality, does it still works?

I have a Peugeot 508 and my driver's door handle stops working when it is cool outside, so I am looking to replace it.
I could get it for €35 delivered from AliExpress. That is 15% of the price from local Peugeot service....

Hello everyone

Does anybody know where the fule fitler is on a Peugeot 308 2018 1.5 Diesel.

I got told the fule filler would done at the Service but then they said thats on older cars because mine is moden....quote they want another 80 off me they said its in the tank ?

No vids online any help would be Appreciated

When ever I open the sliding doors, I have no issues whatsoever. They go all the way back to the bump stops. Nice and smooth, no issues.

But trying to close them is a nightmare. The bottom roller set seams to be stuck or locked into place. I am either going to rip the handle out of the door one day or i have to push from the rear open edge to get...

I'm looking firstly for the oem number of the egr that would have been fitted to my van, and can anyone recommend a good quality manufacturer of an aftermarket egr valve for the boxer?
The saga of the premature regen continues and having replaced all the dpf components, the egr is next on the list to try.
It was previously replaced under warranty...

Hi, new to forum.
I've got a 307sw diesei with eml on.
Black smoke, especially under load and a sort of sucking noise from the air filter the like of which i can only liken to Hannibal lector.
Most of the usual suspects have been checked, EGR, vacuum at turbo ok etc so only the turbo left as chief suspect. Before I cough up a sizeable sum and...

Due to walking away from the C6 I went to see last week, part of me thinks I'm better off with the car I know and sorting it out...

I've had my 3.0HDi 407 Coupe for 3.5 years now and just recently it's started banging into gears, primarily, 3rd and 4th. I spoke to a gearbox place this morning who can supply the parts and they reckon that there's...

Hi Folks, Back Again For Some Info.

I've got a 308 SW 2012.

I've been towing a trailer for years but with ny previous peugeot you could see my taillights with the trailer on so i was never bothered as long as i had reflectors.

Now I've changed trailer I've been told of by the local law enforcement.

I've hacked into wires over the years...

I have a Peugeot 2008 II, 1.2 AT, purchased in 2020 brand new, from a Peugeot dealer. In the first 15000 km I have had the following issues:

1. Climate Control died completely during winter. Fan not working, no air coming out of the vents, completely silent.
2. One lid from the left side, at the end of the wipers’ grill flew away from the car in...

Hello again!I am struggling since last year to cure my 207 1.4 hdi that cuts out very often.I replaced many parts,sensors,fuel filter,egr,but no luck.Recently I noticed air in the fuel lines,especially when priming bulb,lot of air bubbles,also the bulb seems to be soft and would take a couple of seconds to return to its initial state and...

Hello!

The normal phenomenon is that 6 times out of 10, when I turn on the ignition, the FAP additive pump starts for 3-4 seconds? There is no error code in the car. I recently had an Eolys refill. It has been since then.

My car: Peugeot 3008, 1.6 HDi, 9HZ, 2010 (MK1)

1.6hdi. Van is off the road. Been having problems with injectors leaking, looks like fuel overflow to me. Also a lot of gas build up in crankcase, and a lot of fuel in oil. So I intake inlet manifold off and find it's soaking in diesel inside the ports. Does this point to a fault fuel pressure regulator?