French Car Forum

Hello
Does anyone have the torque settings for the main bearing bolts and the big end bolts for the 1.9TD (XUD9)
I have two haynes manuals (405 and Xantia) but the settings are for 1.6...1.8...and 2.0l engines...there doesn't seem to be a mention of 1.9td settings.
Any help appreciated
Thanks.

Hi,

Year 2011, Peugeot 3008 1.6 HDI
VIN VF3**************[VIN obfuscated, can be read by forum staff]

After EGR replacement shows error os disconnection P0405 incorrect position open circuit or short circuit to earth. Had suspicion to it before now look during replacement just got disconnected or it loose cable.

Anybody can point me where to search second end. Loom part number or...

Hi Guys
Am considering the above new vehicle and would love to hear from those who drive one.
Are you happy with the vehicle? Has it been reliable? Would you buy another?

Thanks!

Has the title said,even after the bump a few weeks back the old girl drived ok,
Until today, drove 200miles today to start a new job tomorrow(contractor)
So after finding the site & decent parking decided to get some lunch,that's went the s... hit the fan,pulled over in a layby
A slight bang,little be of smoke or water vapour
Phone a lad who...

Hi everyone
I’m new to here , but I’m hoping someone can help me who has knowledge or advice. Ok here goes, I’ve just purchased a Peugeot Boxer 1.9td 2001 camper with the XUD 9UTF engine. I’ve just changed the timing belt and finding it difficult to find torque settings. I’ve done as per a manual I’ve purchased the bottom crankshaft bolt to...

Our 2019 308sw 1.5 hdi has started to countdown for its service very early, what can cause this ? The normal service interval should be 12 months or 20000 miles if sooner. It has always been serviced by the Peugeot dealer (Pentagon Lincoln).

It was dealer serviced on 8113 miles on 16/5/2023. Then on about 10002 miles on 21/10/2023 it started to...

Hi - I'm stressed but that is not the word !!!!

I have a 17 plate boxer, its had new water pump and timing belt, thermostat housing as it was losing water and causing a long list of associated problems - they have been solved - head gasket - dpf etc

however now my heat gauge is showing ping over to v hot and the red warning circle light...

I recently bought a 2004 Peugeot 407 2.0 HDi (4-door sedan).

I've noticed that the button to open the boot/trunk does not work.

0 button.jpg

Remote works ok, locks, unlocks and opens the boot. I've already removed the button and checked it with a multimeter, when I press, there is continuity between the two wires on the button, but when I...

Hi

what's the trick to remove the radiator off a 2.7 HDI (so get some free hand / tool space to replace the plastic water flange under the egr )

The cooling fan housing encases the radiator and the air conditioning condensor but I can't see any obvious way to remove the fan housing.

My 508 2.0 hdi had to be jumped started last year and the ecu didn’t like it and stopped working took it to Peugeot and they confirmed it needed another ecu so got a second hand one with the same numbers as the original
It worked fine got the car moted then it stopped working and now comes up say electric circuit fault on the dash and nothing...

Hi New to the forums. I have a Peugeot 2008 with the 1.6 HDI Blue 100 engine. I am having issues with the temperature gauge fluctuating, the car runs up to temperature then rises just below the red section then drops down to just above 90. I have had the car checked out by a auto electrician & he diagnosed the temperature sensor switch was faulty....

Hello guys. I am looking for my first Peugeot car so my wife and me kinda agreed on 3008. We were kinda interested more in 508 but the sitting position is just too low for both of us.

We are looking into used 3008 from a local dealer so I would politely ask somebody to check the VIN number for us. Also if possible please to check what...

I have Peugeot 508 2011 - at some point hade ABS fault, ESP fault, hill asist faults on a dash - disappeared on its own in a day. Appeared again after two three months - I have decided,that it is because of the battery, changed it and it disappeared again. For a week or two... Now ABS, ESP, Hill assist lights on and on top of that I am getting...

My neighbour has handed me the EGR valve from his 15 308 1.6hdi and asked me to 'test it'. Its a Pierburg unit as used on many peugeots and citroens, I think the OEM references would be 1618LN, 1702178, 36001487.
I've looked hard but cant find a technical sheet. Its obviously motor or solenoid operated , connector has 5 (numbered) pins. pin 2 to...

Hello ! how can it be set to measure consumption properly? now it reads one liter less than the actual consumption. peugeot 508 2016
:cry:

After a few weeks after having a new battery fitted i am getting the battery symbol and the stop sign on the dashboard maybe once a week or several time in a five minute journey had the AA back out and they have checked the charging all seems okay garage has check for error code and nothing came up anyone had a anything similar

hello
does anyone have the standard journal sizes for the 1.9td XUD engine?
I have the Haynes manual for the Xantia but it doesnt give the sizes for the 1.9td crankshaft.
I was going to have the crank polished ..or even ground if need be...but it looks to be in excellent nick...remarkably scratch free.
I wanted to measure the journals and...

Hi I have received the following error codes after eml came on
P2125 air mixer
P14a4 egr
P14a3 egr
Vin VF3**************[VIN obfuscated, can be read by forum staff]
The codes have been cleared but what needs to be done so they don't come back.

Thanks 😊

Hello, in my Peugeot 5008 from 2014, I get a red warning light on, when a door is open.
When I drive about 5/10km/h there’s a graphic warning in my navigation screen. There it shows which door is open
Is it possible to get this graphic immediate when the car is not driving and a door is opened?
IMG_6115.jpeg

Hi
I have Peugeot 307 model 2006
The following error appears on the screen:
(Anti pollution faulty)
The car's speed does not exceed 30 km What is the reason, in your opinion, with thanks to the experts?

Recently bought a 205 1.8 turbo diesel, it runs great once ur actually moving however when idling it will slowly rev up and down getting to the point where the dash starts to shake and even stall, im not sure whats causing this as when its cold it idles perfectly. i was wondering if this could be a fuel issue as when i squeese the hand prime the...

Had a strange adventure with my Peugeot 407 2.2 2005 the other day and I don't understand anything. The car has been running fine until this happened. Drove on the highway, suddenly the engine dies and the screen shows that the EPS is not working and depollution system faulty . A friend tows us home. The next day I read about the usual error that...

So how many screws are needed to secure the heater matrix tube?

I see online 1 in the middle, middle and under and all 3

Hello. I am having a nightmare with my 2010 3008.

A light has come on the dash and an error code about the Airbag / Seatbelt tensioner. A fault code of 0362 comes up when a snap on device is plugged into it, suggesting that the Airbag Disable Warning light has malfunctioned (not characterised). The seatbelt display above the centre console shows...

Hello Guys, I have a problem with my car. I need to get rid of the SRS light. But I can't get past it.
I thought the problem would be with the airbag, but I don't know if it would be a problem with the AIRBAG Module? I unfastened the airbag, even without connecting the resistor, the B0028 problem disappeared.
Code B0020 is just disconnecting the...

Just a quick one
Does a new Adblue injector have to programed to the car my sons car has a leaking Adblue injector I can replace it but not sure what the score is with the ECU ?
Cheers

Afternoon

After cleaning my EGR valve due to a fault in lexia (cleaning did not solve) I put the fuel lines back together. The car wouldn't start.
I disconnected this line and the vehicle starts and runs fine.

First, what would cause this?
And second, can I run the vehicle long term without it?
Pic attached...

my 207 1.6 HDi has a loose Air Doser, its the big type with 4 pipes off it, I cant see an obvious way of how it fixes on, its rattling and therefore quite annoying

will it become easy to see how it mounts if I just remove the pipes and lift it off the car?

Hi
I search for Peugeot 307 model 2006 wiring diagram if anyone has this diagram please share it
With thanks and appreciate...

My Peugeot 3008 1.6 HDI has started to throw up an intermittent warning saying that the parking brake is faulty, ABS and ESP not working. Sometimes the fault disappears after a short while driving, sometimes while driving, sometimes on turning on ignition, seems very random. While checking the fuses and wiring under the bonnet and jiggling wires...

I am very interested in the 1.4 XS. The early 1.4 had 65bhp-ish. I was curious what they have made the XS output of 85bhp, which is 20bhp more.
Is XS suspension firm or all 205 are same?

Because I am interested to look for one XS.

thank you.

I have a Peugeot 5008, 2012, 1.6 HDi 1560cc 82KW 112HP 9HR (DV6C)

A warning light starts showing Engine Failure followed by particle filter additive level too low repair needed

I found the right genuine type as 9736A0 Diesel Fuel Additive DPF on amazon, but it costs 3 times the alternative on ebay. There is also a PAT Fluid PDF, but not sure if...

I am reaching out to you as I am facing significant issues with my car.

This past Saturday, I experienced a flat tire on the front left side and had to tow my car. Subsequently, I acquired some good used tires that were fitted to the front axle on tuesday. It's worth noting that the original tires were 225/65/R17, while the ones we fitted were...

My son here in Australia is wishing to buy the above named model. How do we go about checking to see which recalls it has had. It is a 2018 compliance and its vin is VF3**************[VIN obfuscated, can be read by forum staff].

Right then just when I thought I had finished all my jobs I started the car with the bonnet open and a puff of exhaust fumes from the front of the engine.

Appears to be from under the turbo heatshield at the turbo to dpf joint and after some research It seems dpf needs lifting and holding in place to properly engage before tightening.

My...

Ok so a new to me car and as per the subject the Peugeot tells me emergency call requested then I have to explain to the nice person the car has gone insane and I do not require assistance.

Car parked and locked, click keyfob to unlock, open door and before even being seated it does the emergency call requested press aqain to cancel. Red phone...

Following on from my post the other day about potential purchase of a Peugeot 3008, the deal is not imminent.

Obviously, as a die-hard Citroen fan, I've read numerous horror stories about C5 X7 steering racks on certain models.

I am therefore wondering if there are any similar horror stories to watch out for on the first facelift Peugeot 3008?...

Hi All - Can anyone help please?

I have a Peugeot Boxer 2.0HDI (Boxer 335 Pro L3H2 Blue HDI) which is giving out large amounts of white smoke from the exhaust when the engine is warm.

We purchased the van a couple of weeks ago and had no issues while running locally, we took the van on a long run approx. 200 miles and about 30 miles from home...

Hey guys, I just got a new 2008 a couple of weeks ago and I noticed this low-key sound whenever I press the brake while driving. It is like air is being let in or out, similar to the sound of a small air pump, but quieter. I understand it has something to do with the brake servo and possibly vacuum booster. I did not notice it before probably due...

Hi all,

I have recently purchased a 1997 406 2.0 petrol estate (engine code XU10J2TE) and I have a few questions:

1. The car came with two keys - one fob (door and boot unlock buttons) and a plain key. The fob buttons work to unlock the central locking and both keys do the same. But if I want to start the car I need to press and hold the door...

Hi everyone,

I recently bought a Peugeot 107 2 Tronic with a gearbox issue. I connected it to Peugeot planet and received the following error message:

Automatic transmission control unit
Permanent fault. Clutch actuator motor signal.

I have already replaced the actuator with a known good one, as well as the gearbox relay and checked all the...

Hi all, my 308 1.6hdi tsarted missing occasionally but has got progressively worse. First, repeatedly stalling at idle. Then, refusing to or being reluctant to start after stalling. After that, having no power when revving (ie having to give it a couple of thousand revs or more to pull away from a stop without stalling). Now, it will catch when...

I am going to add a cruise stalk to my daughters 2007 207 Sport. I have popped of the trim and the connector on the column has 8 contacts. Does this mean I can use a stalk with the memory function or did all the connectors have 8 pins and some were simply not connected on the vehicle? Thanks.

Ive had a few ODB codes randomly come up, trigger the MIL light and suspect there is a common loom plug / connector that is loose or needs a clean (eg the poor contact below gives it away)

Codes are

P0180 Diesel fuel temperature signal fault : Coherence
P0181 Diesel fuel temperature signal fault : Poor contact
P0183 Diesel fuel temperature...

hey
i have peugeot 1007 , i have problem with ESP... first on car start to come Abs and esp light ... i put on diagnostics and the error was c1380 pump abs.
abs esp lights was on some times and go off ... and after that was all time on... i check cable.. fuses all ok... i change the abs pump ...
and now just the esp light is lighting On ( esp...

Hello all,

I know this subject has been dealt with before. I seem to have no clearances on some of my valves, leading to very difficult cold starting - a known problem with these engines. Can anyone tell me a source of replacement shims, and also the special tool I understand is required in order to swap shims without having to remove the...

Hello All,

I’m hoping to benefit from your expertise. My wife has had her 2010 207 Sport Auto for 11 years, bought with 6k miles, now done 42k. Peugeot main dealer serviced, then by a good recommended Indy. Car has never missed a beat in 11 years. About 800 miles ago got an anti pollution warning. Fault codes from Diagbox were P0014 and P11A8,...

Hello, I am new to the forum today, I am a Norwegian so please forgive me my French .

My car is a second hand 5008 1.6 BlueHDi 2016.
I am not happy with the late start of washer pump for the windscreen, wipers are starting before washer.
I am looking into the possibility to put in a toggle switch to start the washer pump in advance.
Can any of...

Hello,

got this trouble code on a Peugeot 508 2017, 1.6l petrol, 165BHP - Couldn't find any useful info about it on the forum as well.

thanks for your input.

Hi could i please request some info regarding tightening torques of the clutch and flywheel ? As the kit from valeo doesn't include any instructions.

I need the torques for the flywheel bolts and the torques of the spring plate.

VIN VF3**************[VIN obfuscated, can be read by forum staff]

Thanks,

Bart