French Car Forum

Hi to all.

When i turn on side lights de horn turn on too.

Hi guys, thanks for letting use this forum. I just wanted a little advice if I may. Cut a long story short I had some discs and pads fitted to my Peugeot 508gt 2.2 last year that was very poor performance, handbrake struggling to hold, brake fade was terrible so i replaced them the other day. I took the electronic handbrake off, jacked the car up,...

The old Hdi has been running well until yesterday.

I took it for a spin up the coast 200kms to burn off the cobwebs on the freeway and ran fine. Stopped over night and next day all well (eg no oil stains on the driveway)

Went for a short drive (10 kms) at low speed and stopped at some shops. Came out an saw a wet patch under the car (auto...

Any ideas anyone?
I put Diagbox on my car, 2006 Peugeot 307SW, 2.0HDi 138, as I needed to programme a new key. In doing a faults test it tells me there is no communication with the additive ECU. The car isn't actually showing any faults at present.
The additive is the bag type and I have changed the bag.
Any clues as to how to start diagnosing...

Hi guys,

I have, what is sounding uncomfortably familiar on this forum, EPB issues. I'm not going to go into detail on the fault just yet as there are a lot of other great posts here that I want to work through first, but can somebody tell me please where the parking brake module is located please, like the one pictured here:

Sorry I know...

Where can I find the RPO number on my 207cc?
ServiceBox says it should be on a sticker on the left door but there's no sticker.
There is a sticker in the left door jamb. (see attached)
VIN is VF3**************[VIN obfuscated, can be read by forum staff]

At the weekend I disconnected my battery to route a power cable for a small amplifier. I followed the reset procedure noted on the site but had a horrendous experience when i connected it all back up. Hand brake failure alarm, engine fault warning, service flashing, window shut itself and wouldn't open locking was half working, when I tried to...

Hello, for about 2 years, yes, you read correctly, 2 years... What bothers me is the malfunctioning ESP or Semi-functional. It works until I pass a corner at a minimum speed of 60 km/h until then everything behaves fine and ESP works. Then when I turn off the car and start it again the error is gone and it repeats itself every time I drive. Lexia...

Hi guys.

My expert is.... Causing me hell. She has 205k miles so have to be lenient.

So.
Symptoms of this latest issue.

Doesn't start. Just CLICK.
Bump start backwards down hill.

Drive to next job.
Park on hill forwards. Try. Lazy turn over.

11.98Vdc

Assumed it were the LION battery I fitted from ECP in December.

Changed battery for...

Hi,
I have the cylinder head of on my 208 (EB2 engine). It started with a new timing belt and then I realised it wasn´t that much more job to change the valve steam seals because the car use about 1 litre oil per 1000 km (thought this maybe would help a bit?).

Then I had to take the top of because I accidently damaged a valve when taking one seal...

Hiya my Peugeot partner combi 20hdi 2004 had a new cambelt fitted after a short while about twenty miles it broke down eventually started to get me home then won't start again had a garage look at it they said the timing belt snapped so they fetched it back i went to start it and it started ran perfectly but when hot it would not start again so...

Hi all,

Apologies for the trivial question but I'd like to replace the spark plugs on a 1997 2.0 Turbo (XU10J2TE) and the layout is slightly different to what I've found online for (presumably later) petrol engines. Instead of a plastic engine cover and a single ignition coil pack for all four plugs, I seem to have individual ignition coils (see...

Hey all,
I've searched and searched and I just can't find the info I need, I'm happy to pay for it if someone has it.
I've got a 2021 plate boxer, I've removed the double passenger and fitted a single and therefore the pretensioner wiring doesn't fit, throwing an airbag fault code.
I'm told I can fit a resistor into the wiring to fool the circuit...

Just looking to see would it be possible for part number DSF - Shock absorber.

Vin: VF3**************[VIN obfuscated, can be read by forum staff]

Kind regards.

I have an oil leak from the oil cooler/filter housing, car has over 200000 on the clock. So I will replace the gaskets on it.

I'm also replacing the Turbo. As I am getting an intermittent error on the Turbo P2566 and it has to come off anyway to get to the cooler. I think it may be coming to the end of its life.

1.6 partner teepee (BHY) 2018,...

I bought this car here in the motherland, France (my first Peugeot) about a month ago and have finally sorted the maintenance receipts (I'm the 4th owner, it would seem) and I have a few questions about service intervals and oils. The car has 193k km on it.

1) Peugeot recommends a ridiculous 120K km/10 year interval for a timing belt change. This...

Can any one help me. I have looked around the Internet but can't seem to find want I am looking for. I have a Peugeot Partner B9 and looking for a replacement catch for the rear seat, the one that locks into the floor holding the seat down. I can't seem to find a replacement or a part number can anybody help.

Morning all,

Struggling to find much regarding the specific problem I am having, and as I'm now running out of things to check, I thought it was time to ask here.

My 1.9 XUD n/a engine in my N reg 306 has refused to start via the key for some time now. I left it stored for a while over winter after discovering this due to a lack of time more...

Hello, I own a Peugeot 308 GTI from 2018 with the 1.6l 193 kw. Yesterday the engine light and the service light came on the car also lost power. This afternoon I went to my local mechanic and the fault code P0235 popped up. This has something to do with the turbo pressure sensor. Did anyone had the same issue or can you help me to locate the...

My wife's 207 is running lovely with the exception of a very random burning smell that is really strong and comes and goes.

It smells like a burning clutch but the clutch is not slipping at all and was changed about 40k miles ago with an LUK one. The burning smell seems to have started since my wife drove through some deep flood water at the end...

Guys

Got a car from Copart, its a P5 Peugeot 308 2022 ex police. However i have couple of questions;

1 - do i need to program a replacement ballast? Spoke to stellenios & you , they reccomend a new ballast to be programmed. But its a sales guy.. i have the headlight

2 - I have some cables and a connector. Can someone please help me to figure...

Hi everyone, I am new to the forum and I have a few issues that I would be so grateful for any help with!

After spending hours searching forums and watching videos I am not getting anywhere!

The car is a 2012 207 1.4 vti. It starts and runs although lumpy on idle.

The fault codes I have are:

P1062 variable valve lift system position regulation...

After some advice if possible.

Trying to recalibrate the steering angle sensor on a Peugeot 5008 2012. I'm getting the following codes. I have made sure the wheels are dead ahead. But it keeps failing and illuminating the ESP light. Does it sound like the Angle sensor/ Clock spring I purchased is faulty or could it just need reinstalling? Thanks...

Hi everyone,

I am trying to find out if I can fit a secondhand ECU to my 2012 207 1.4 vti without the need for matching it to the car in some way.

Could anyone tell me if it will just plug in and work or is there more to it than that?

Many thanks

Hi all,
3008 GT 2019 does anyone know how to remove front plastic headrest guides/ mounts?
Thanks in advance

Since I had some issues with my 2012 Peugeot 308 RNEG unit, I've taken it out and sent it for repair. After taking the unit out, and driving without it for a couple of minutes, a check engine light appeared.
I've not noticed any changes in driving, and everything seems to be working fine (engine-related).

I wondered if the check engine light is...

Hello

I have recently just replaced the Engine Bay Fusebox 9667199780 on 207 sw due to water ingress on middle brown connector

When using tool now I have the below faults

P2426 - Exhaust Gas Recirc Valve (EGR)
P0031 - Oxygen Sensor Heater (Bank 1 Sensor 1)

When replacing fusebox I had to splice the cables to allow connection in doing this I am...

Hi everyone, I’ve just joined the forum and this is my first post hoping someone can help me to find out why my Peugeot Partner 1.6 HDI van (2012 reg, 99k miles) doesn’t start. I’ve only had this van for 5 months and last week while I was driving to local supermarket it stalled and wouldn’t start. Every time you turn the ignition you can hear and...

Hello,
WhatsApp Image 2024-03-05 at 18.28.57.jpeg
Can someone please point to i should check. i have replace the turbo actuator position sensor since fault is permeant with missing or disconnected sensor.
I have checked the voltages on the terminal socket. and measured 5 volts on point 1&2 against -ve terminal of the battery. I believe it...

Good morning

This code and the text in the attached pic popped up this morning, car seems to drive normally.

What should be the protocol for this code?

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]
IMG_20240218_095131.jpg
Thanks

Peugeot 3008 1.6 165bhp VF3**************[VIN obfuscated, can be read by forum staff]**************

Hello,

I had a P11A3 fault code (i put up a post a few days ago) and it disappeared after replacing the VVT solenoid (stupid engineers, took me hours...) but this P0010 code popped up (and check engine light is on - i can't earse the fault, it is defined as permanent ).

The car seems to run fine , maybe...

I have a Peugeot 207 sportive 2011.
The right hand window control needs replacing. Some sites say part 6490EJ. Others say 6490EH.
Just wondering if they will both work or if there is one to choose

Hi everyone, I'm new here

I have a 2010 peugeot partner with an oil leak, I have located it to be coming from the manifold seal between 2 injectors.
I've got most of it stripped down however the HP fuel lines are in the way....has anybody got an eay way of getting these off?
Also how does the airbox come out from behind the engine?

Thanks for...

Bonjouir from downunder.
Would anyone have the circuit diagram for the control of this flap. It is the slide button type control mounted above the radio. I have the controlling motor removed and it seems to have no faults. The internal gears are ok and on full heat the ac pump turns off ok. I think the problem may be in the dash control unit. I...

hi guys the vacuum pump on my 205 1,8 d has two pipes coming out one obviouslt goes to the breaks and they work fine but the other pipe just sits in the engine bay and is cut off. can someone tell me where this goes to. Thanks

Hi all. I have a 2011 Peugeot 3008 and I am currently having problems with the (front left) ABS system. I have replaced the wheel sensor and also the wheel bearing and the ring sensor, but the ABS and ESP lights are still on. The wheel sensor has been checked and is fine, it seems as though the problem is above the sensor. Could anybody please...

Can anyone tell me if the key on my 2006 307 uses ASK or FSK modulation? Was about to buy one from Aliexpress but my existing key is obviously a universal replacement and does not have either of the original CE0536 / CE0523 markings on it anywhere.

As mentioned elsewhere, I have had issues with our 308CC not charging the battery properly. The alternator does produce current to balance the load, but the output voltage would not rise over 12.8V. usually hovering around 12.5V.

I have tried fitting a second hand alternator from a Mini Cooper with a similar Prince engine, and it is a little...

As it just annoyed me.

When it comes to replacing the battery, is there any reason why I can't now use a wet battery of the same size and capacity, instead of the old AGM that is fitted?

Is there any difference in the charging circuit for AGM, that would preclude replacing it with wet?

Cheers

Hi Guys,

2014 Partner Horizon 1.6 Diesel Manual - Wheelchair adapted (for my daughter to use).

New to the forum, I've a good sense of humour and can take a joke and ribbing, I can give as good as I get and I'm not easily offended.

Needing a bit of advice and feedback for a fault code on the ABS ESP system, drove the car on Friday past with...

Afternoon all,

Well she went and did it so I need to expand my knowledge on the new technologies it has.

First off is the electronic parking brake. I've read that these can be a problem so how do they actually work please?

I assume that there is some kind of servo motor which winds the caliper on?

Honestly, I have no idea as I've not even...

Hi, the aircon in my 2004 206 GTi 180 has an intermittent fault. When it first occurred, the fan failed to run, but after a few days it came good. This behaviour kept repeating, but with increasingly longer periods when it wouldn't run, until it eventually it stopped working altogether. I took it to an auto electrician who tested it and said the...

Hi got peugeot boxer 2.0 hdi 2018 model driving along and just cuts out will start and drive again no probs till it cuts out again no warning changed camshaft senor and fuel rail pressure sensor any help would be great

Hello,

I’ve recently sent my van in for front brakes and discs, cambelt and water pump change and leaky thermostat and then they told me the seals needed to be done on the injectors.( all in £1300) So I got the work done and got the van back (had to set the clock) I then found an oil leak which never existed before!

I asked them to have a look...

Driving back through France to the UK last week the dashboard, and then the centre display, showed these warnings:

IMG_20200902_131145855a.jpg
This showed first and then, when the UREA warning light started flashing, these also came up:

IMG_20200902_162052584a.jpg

IMG_20200902_162103453a.jpg

At one point this message showed. I had...

I have a 2010 60 plate Peugeot 3008 2.0 163 automatic. Fully serviced and looked after.

Yesterday I accelerated hard and the revs went up but as I did so, I heard a loud pop and the car went into limp mode with errors lighting up about the gearbox ,engine, esp, parking brake.

Got home to find a rear blowout and the tyre was completely flat. That...

Hi all, 

I thought I would post this up just in case it helps anyone else in the future with the same issue.  

I have a Vivaro 2021 k0, which is an Expert.  I had an engine fault code pop up and the van went into limp mode.  Scanning gave the following faults:

- P119F Deterioration of the engine oil.  Rate of dilution excessive
- B162C...

Hi, I have topped up my additive tank 30/40k kms ago and reset it on diagbox. Now diagbox tells me there is 95 procent in it but get a pressure fault because it’s empty! How is this possible are the settings not good or is there a internal leak somewhere? There are 2 bolts on top of the tank does anyone know how to remove this?

Do I need to...

Hello
I managed to get the engine out of the van....this engine had less that 30k on it...1.9td. Its in a Ducato motorhome, I can now see the full extent of the damage.
The hole next to the starter motor is where the oil filter housing used to be.
It was lent to someone to help them out and this is how it came back!...there is a hole in each side...

Hello
Does anyone have the torque settings for the main bearing bolts and the big end bolts for the 1.9TD (XUD9)
I have two haynes manuals (405 and Xantia) but the settings are for 1.6...1.8...and 2.0l engines...there doesn't seem to be a mention of 1.9td settings.
Any help appreciated
Thanks.