French Car Forum

Hello! Can anybody help me with this problem I have with my Peugeot 3008 gt line 2019 diesel.
The car has 76,000km and has been fine until I thought I would top up the AdBlue even though the car hadn’t popped up asking to refuel. After filling the AdBlue 5minutes later the engine fault, spanner and Adblue light all came on. I’ve been told my a...

I've search high and low but could not get a answer to what the cylinder numbers and injector numbers are on a HDi 2.7 litre V6.

Below is what I have deduced using data off Landrover forum re the 2.7 TDV6 engine (uses the same 2.7 block) (turned to the right for the Pug traverse mounting)

This is to id two injectors that Diag is reporting as...

I have a peugeot 308 mk2 2.0bluehdi 150bhp on a 2016 year.
Everytime I start this it revs at constant 1200rpm and says engine fault on the stereo screen and a service light on.its been serviced and I have pressed the dash button to reset the service interval but the service light on the odemeter does not go out.
I was worried and called out...

Hi,

I'm looking at buying a 2022 boxer van. The van dealer states it comes with a manufacturers warranty but is there any way to check if it will be honoured?

It was first serviced end of 2023 at 42k miles, then just recently at 53k miles.

Any help much appreciated :)

Hi Guys,
Back again with an electrical problem, with a 2000 206 GTi which does not operate the cooling fan in front of the radiator. The car has Air conditioning, and we checked all fuses but cant get power to the fan. When we manually add power to the fan then it works when we reverse the power the fan runs the opisite way so fan is perfectly...

Hi everyone. I am new on this forum looking for some help. I bought a peugeot 2008 year 2018 from an ouction which has only done 12K miles. The car was dead. After some detective work we found out that ecu was burnt and no one was able to clone/programe replacement ecu apart from main dealer. We chose to get immo off ecu. The car starts and drive...

I had a leaking injector but was runing fine i replaced the seal and guide now it will not run....

i have fault code
P2150 fuel injector group B supply voltage circut low.
P0201 injector circuit/open cylinder 1
P0202 injector circuit/open cylinder 2
I have unplugged the fly lead that feeds these two injectors from the injectors and from the loom...

Yesterday I drove normally when I heard a very small noise, like maybe a plastic part came loose and was clattering. From the engine compartment. I stopped, then the engine stopped by itself, and I haven't been able to start it since.

In retrospect, the engine did not always start immediately, it sometimes took one or two seconds longer, and not...

Good afternoon collective knowledge

Working on a 208 Blue hdi. VIN VF3**************[VIN obfuscated, can be read by forum staff]
Got engine management light on.
2 Codes : P20F600 & P306300, De nox circuit and High urea pressure, suspect ADblue injector blocked,
I have removed injector and cleaned the crystals from the end but not sure how to bench test and clean interior

Or am I on the...

Hi!

I am having an issue with my cruise control and I was hoping for some guidance how to tackle it.

The issue presents itself after a hard acceleration, for example, getting up to highway speeds, after which the cruise control starts blinking and cannot be activated anymore.
It’s only able to be activated again after the car has been turned off...

Afternoon all, need some help.
Got a tidy 308 with 122k on the clock, runs lovely and very reliable. Im retired now so dont use the car but for the odd run out(good 50mile round trip at speed mind..) High-days and holidays as they say. Im a mechanic/electrical eng so know my way around a spanner. Did a Diagbox run and a couple of egr errors popped...

This is just a quick one - what is the part number for the metal (possibly bronze) gear lever bushes where the lever attaches to the selector rod under the car?

The car is a Partner combi Mk1 2001 1.9d. I found a couple of possible replacements for 205s and 206s but no idea if these would fit.

I replaced them with a plastic set I got cheap which...

I was starting on the job of replacing driveshafts today and spent around 3 hours hammering at the driveshaft bearing collar to hopefully free it from the rear engine mount. I've removed the two bearing retaining bolts and didn't attempt this without removing the hub. That seems like a silly thing to write but I've seen some forum messages where...

Aft'noon.

Changed the gaiter on the rear shock of Sylv's Peugeot on Thursday and now there is a distinct noise when going over speed humps that wasn't there before.

I'm left wondering if it needs some kind of lubrication where it slides over the shock as the shock articulates.

They say, If it ain't broke don't fix it! but it was broke, I have...

Garage says the gear link cables need replaced. Peugeot want £239 for a complete gearshift and cable unit (PART 2400PH). I just need the two cables though but don’t know which part it is, can anyone here assist if I post the VIN. Not sure if its even ok to post the VIN here?

Any advice or help with this part would be most welcome

Bonjour à tous ! L'ordre des modes de conduite affichés sur le tableau de bord est
SPORT
NORMAL
ECO
le problème est que (cela ne se produit que lors de la première utilisation du commutateur à chaque allumage) peu importe que j'appuie sur la flèche HAUT ?? ou sur la flèche BAS?? le sélecteur démarre toujours à partir du mode Sport et fonctionne...

Hello.
Can someone help me.
I have a Peugeot 208 Year 2013 1.6vvti 88kw/120hp.
I have a permanent error code U1F1B:08 Error Bus LIN 2
What does this error mean?

Hello to ALL,

I have search everywhere what kind of problem is that but without any results ... Anybody could point me to the right direction ?? Thank You for any kind information.

RETRO_INT: Main beams assistant ECU

B100D 04 : Operating temp. too hight.

Please see the attached screenshot of the fault.

Got my van running with a flashing dash milage and lots of warning lights, could not get any can communication so sent cluster away for test and repair it had the LED faults thats common reason for nocan communication is the cluster is not programmed to the van so i’ve got my diagbox and vci can get into the realignment but i get failed operation...

Strange one. My mates car, 206cc 1.6 petrol, vin VF3**************[VIN obfuscated, can be read by forum staff] had just driven across the UK and then 1/2 way down France with no issues at all, He parked it up for 2 days and it wouldn't start, not even trying. He thought it may be very low on fuel so put a gallon in it, still no joy.
I've plugged Diag in and am struggling. It gives 3 options...

The RT4 won't remember the date and time. Once the settings are saved and the motor is turned off, the data is lost (once the car and the RT4 starts again it shows a completely wrong date in 2000 and a wrong time).

Any advise

Hi got these messages soon after refilling 2012 partner 1.6 d 72,000 miles drives fine, I've blasted down road and sat stationary at high revs 10 minutes still there to it's ex mobility so has smaller tank as I've read about some elos pouch that needs replacing? But not sure I'll have one as different tank.
Any suggestions would some additive in...

Hi!

I have a 2019 5008 2.0 HDI VIN VF3**************[VIN obfuscated, can be read by forum staff] that has started giving fault message when the automatic headlights are activated. If I turn them of the error message goes away.
Have checked the sensors both front and rear and they are fine. The connection is good and I can not see any stripped wires. The arms are not broken and everything...

Strange issue with headlight / indicator
When locking/unlocking the nearside headlight flashes not the indicator and vice versa the Indicator comes on when the high beam is selected and there is a buzzing coming from the offside headlight, the left indicators flasher relay is clicking a lot faster than normal with no flashing of the front bulb,...

Just read Marc’s excellent topic here:-

Would this be the same for a 63 plate facelift does anyone know?

Sylv’s has finally come up with its first faults.

Parking Brake
ABS
ESP/ASR

Read a few o posts here and elsewhere and it sounds like it could be an ABS Sensir fault.

Unfortunately, I’ve not got a suitable Lexia to cover this late car....

Can anyone give advice on ABS?
Short questions are:
1. ABS not activating and there's no codes in lexia or dash warning after bleeding is it damaged?
2. Is there a speed limit for ABS - I tested on a steep slope at about 25 mph
3. Do I just need to repeat the Lexia ABS bleed process?
4. Is no comms with ESP the clue or red herring?

Background...

Hi All.

I have had my 2017 308 GT Line 2.0 blue HDI in at my local Peugeot dealer.

I had pluming white steam consistent with an AdBlue injector fault.

Peugeot put it on the computer and diagnosed a failed AdBlue injector and this was replaced. This in turn had shown up a blocked DPF. I have previously had no issues with the DPF (67,000 miles),...

2009, 73k. I’m after some advice on what to do next please.
My car keeps going into limp mode with Warning triangle, system management fault message and the fan kicking in. I leave the car off for 5 mins or so and when it starts up again the warning light and message goes off but it’s sluggish, lumpy and generally not running nicely. This keeps...

Hi!

I'd like to update the navigation system on my Peugeot 3008 from 2015. Could you let me know how this can be done?
Unfortunately, the service places around me either don't want to hustle or ask for ridiculous money.

If needed, the VIN number is: VF3**************[VIN obfuscated, can be read by forum staff]

Guys

Hope everyones doing well. Just had my peugeot 308 p5 airbag 2022 had replacement airbags. He also sent the module to get it reset crash data. However module arrived but he said he could not communicate with the airbag module.

Can anyone help me ? I need to reset the airbag module.

Guys I'm working on a water damaged 2021 Partner 1.5 diesel.

I've been given some wiring diagrams which have been a great help.

1) Engine starting
2) Electronic fuel injection
3) ECU connector pins

I would really like some info on the BSI pins and the ABS module and steering sensor.

I have paid for an hour on Service Box but cant seen to...

Hello,
over the year I have been doing big service on the car. It started on 5/2023. It should have been a simple timing/belts job but then I noticed that when stepping on a gas pedal the coolant is going up. There were gasses coming to the coolant (no oil mixing yet). So I did the headgasket job including full top end gasket set and all fluids....

Hi, so im embarrased to say im a Mechanic, but today i went in and did business as usual, changed discs+pads in the back of my 3008, I didn't do any research beforehand, so i just went ahead, things went great, i used a gutmann to put it into service mode - here is where things may have gone wrong, i didnt push the piston back, instead i spun them...

I have a 2004 Peugeot 407 with the 2.0 HDI engine (138 hp).

I just now got the car running and driving (it had a small crash on the front, so it wasn't in driving condition). Car starts ok and vibrates just a bit (normal for a kinda-old Diesel car), however, when I rev the car (stationary or moving, in gear or not), there is a horrible vibration...

Hi all what software and interface do i need to programme my instrument cluster to the vehicle turned up as non running with flashing clocks no can unit tested been advised this needs coded to the vehicle. 2013 boxer all software seems to want to run on windows XP PP2000 & Lexia 3 then digibox any help appreciated or if anybody local to Newcastle...

can someone pls help if Peugeot 308 keyfob from 2010 uses FSK or ASK, incase it helps, VIN is VF3**************[VIN obfuscated, can be read by forum staff]

is it based upon year of manufacture or could it be different for same year models depending on some other factors ?

Hello, I am having a nightmare with my Boxer 3 Euro 6 2.0 BlueHDi Van and wonder if anyone here can help, please?

I’m new to the forums as a user but have been browsing for a while for advice, and I would like to thank you for all the information that has helped so far. I would be grateful if anyone could help with my issue below, as the garages...

I see alot of people having this problem.

The engine goes around but wont start.

Can't lock or unlock car on remote key.

Car won't beep when keys are in ignition when I open doors.

I have good battery. Fully charged.

I have icarsoft Cr max and have read codes.
These are the three codes that are showing.

Check files added.

EDIT: when I...

Hi.
The Electrical circuit failed: have your vehicle repaired error pops up every time I start/turn the ignition on.

I ran a diagnosis with Diagbox and I get: B1601 15 -> Central power switch positive (+CPC) relay control fault.

I own a Peugeot 508 hybrid 2012 ( 200 Horsepower model ).

Context:
Today I got some mechanics to try and fix the...

Hi there,

I have been on this one for a while and despite new EGR, electrovalve, DPF, MAP sensor and MAF clean I can't find the exit - can you help ? Is there one ??

All the classic systems are there - starting and idling OK, but running it is short of power and stutters just above 2k rpm. Applying some kick down brings the power back, but...

Hello to all. Couldn't find a good secondhand radiator for our 205td, and a new one is horribly expensive.

After waiting a long time, found a very cheap one with leaking matrix. The plastic spigot on the tank is damaged on our original one.

We are going to have a go at separating the plastic tanks at each end of the matrix to cobble together...

Hi all
Despite following the BSI reset and anti-pinch window reset, the passenger window would only raise and close in small steps when operated from either the driver or passenger controls.
Driver window and rear windows working normally.
I've just tried silicone spray on the passenger window seals.
The window then raised in small steps but now...

Hi all.
Am usually in the Citroen forum, but am looking to buy another French car.

So this Peugeot model.
At just over/under 100,00 miles, a lot of them are for sale at about £4000. For what reason?

Is there a common expensive fix to be needed by their former owners?

I have a workmate in a 2020 model. A month after buying it was returned for...

Hello all,

Apologies for the long post -

End of Feb, I bought myself my first frenchie - Pug Partner 2.0 HDI, 54 plate.

I was made aware there was an ‘intermittent fault’ in that occasionally it wouldn’t start and I’d have to unplug an injector and it would start. The other intermittent fault’ was the wipers would come on whilst driving...

I have a warning on tha lane departure and lane assistant.

The error codes are
B1000 54 Download of the calibration of the multifunction video camera

And downloading date is ??? Under identification
20240803_133233.jpg

Tried the dynamic calibration where you Drive in 70 road for a while but it ends with an error.
20240803_132033.jpg

Anyone...

To cut to the chase, my question is, should I bother dropping the sump and checking the oil strainer of a 1.6 HDi with unknown history? - I need to change a leaking oil feed pickup so have to get my hands dirty anyway.

Some blurb you can ignore unless you're bored:
I've acquired a 207 CC that hadn't been looked after (at least hasn't been looked...

Replaced injectors on my euro 5 2015 boxer. New seals and bolts plus a new leak off pipe.

Engine cranks over but wont start up. Getting the P2291 26 code.

Please see attached the reading from diagbox. Any advice is welcome.

Thanks.

I have a 207cc with an intermittent airbag fault.
The fault is E602, and it's obvious from the live data (see enclosed graph) that this is a high resistance on the 'Level 2' side.
So, I remove the airbag to check/clean the connectors as first port of call.
Removing the airbag gets weird. (see enclosed photos).
This car is a 2008 vehicle and the...

Hi Amazing people

We changed the clutch and starter on my 308 SW (1.6 D) last weekend, and rebuilt the car and engine, it fired up once when we reconnected the battery after the rebuild.

but then accidentally snapped the end connector off of the negative terminal that has the two wires that go back into the wiring loom. I have sourced a...

Hi,
Wondered if anyone can shed a light on a roof issue with a 307cc 2006
The sequence starts, the boot lifts then stops. The side 'paddles' do not activate and so the roof does not fold down.
Could this be a sensor or actuator issue? If so how do I go about finding it?