French Car Forum

Hello, I have a Peugot 207 HDI 1.6 (2007) 90hp and I want to transform it to be as powerful as it can be... I am quite new to doing custom builds but thats why I am here asking for advice.

What engines would fit best in the car and what else could I do to get the most power out of it, e.g; 500hp or something.

Just bought a 2014 3008. The door mirrors never folded when locking. The other day was adjusting mirrors when noticed when adjuster is set in the middle and pulled back both mirrors twitch as though trying to fold. Also this happens when locking and unlocking. This affects both door mirrors. Question is have they been deactivated or have both...

Hi guys
i would like for some help please
208, 1.2Y, 2019
42 KKM

Last week 3 warnings appeared on my dash:
TPMS
Wrench
Control to prevent wheel slippage

i scanned and i saw this attached fault code : U1213 81

any leads?
Thanks a lot

Hi!
My 308 1.6 VTi made in 2009 has the AL4 4-speed automatic transmission which shifts roughly from 1st to 2nd gear, every other gear changes are smooth. The car has ? 150K kilometer mileage with no gearbox ATF fluid change.
What could be the issue?
Thank you.

Having cracked a rear fog unfortunately water crept into the parking sensor and into the wiring loom. This resulted in intermittent faulty sensors and finally the system stopped working. 4 sensors were changed and the wiring loom replaced. This did not resolved the issue. The ECU was then changed. Upon plugging the diagnostic in, faults still...

Hello, because of an error, I had to buy new gauges for our Peugeot 206 (MUX). The new gauges have all the needles (fuel, temperature, RPM and speed) set in bad positions so they show bad info. Is there an easy way to reset them to default positions? I no longer have old gauges (they were swapped for repair for the new ones) to get positions from....

Hi all, I want to get a new blade cut for my peugeot partner online. I have the 2 barcodes with codes below, that came with the owners manual.
Would anyone be able to explain which digits to use to order a cut key and which to programme key to van.
I hope @wheeler will see this post, pretty sure he will know exactly.
New here, so not sure if I...

Hi All.

I have a pronounced engine vibration. It’s most noticeable on tickover.

Clutch in or out doesn’t seem to make much difference. I’ve recently passed an MOT so unlikely engine mount. I’ve had a garage suggest crank pulley but this was checked and ruled out. He thinks probably DMF although there is no rattle or metalic noise that’s...

Hello gentlemen, I am the owner of a Pejo 207 1.6 HDI 2009 model vehicle. My vehicle stalls while driving, and when I wait a while and start, it starts. There is no error when connected to the computer. I replaced my vehicle's diesel pump sensor, rail sensor and crank sensor, but the problem continues. The problem happens a few times a week or...

Hi,

Proud owner of 1.6 HDI, got a quite a bit of a problem here.
I've been driving Peugeot Partner B9 1.6 HDI 2010 DVE6TED4 for quite some time and it hit 420000km lately, overall no problems until now.
P0299 Underboost, i checked the turbo, it holds vacuum and is fully engaged at idle ( :?: ) , no hissing when i step on the gas, cleaned the...

HI,

I got myself a 207CC from 2007 and initially everything worked fine. However, recently the roof does not open complete any more: the windows go all down, the boot opens fully, the roof starts opening but stops after about 10 cm. I'm pretty sure one of the microswitches is the problem here, anyone know which one this specific is? I'm...

Hello there,
I have a Peugeot 206 and lately it starts up rough if it hasn't been driven that day, idling at 300-400 rpm then jumping to a normal 900 rpm after 3-4 seconds

It has to be noted that when the car starts up this way, the airbag light goes on, and when I restart the engine after this rough start it starts up normally, idling at 900...

Got a mk1 Peugeot 3008 1.6 BlueHdi that has a leak at gearbox on driveshaft seal. Just going to change both while at it and I am hoping someone will be able to shed some light on how much oil the gear box takes as I know you drain completely then refill with correct amount as there is no level on it.

Hi all, I'm new to the forum, so apologies if this is something obvious, but I've looked on several forums and haven't seen anything quite like this.

So I've had my Peugeot 2008 (2015 model) for just under a year. Its on about 64k miles. The previous owner serviced it every year and it seems like they really looked after it, but the past couple...

Well I thought it was about time to start recording any developing issues on Sylv's car and start a blog. May as well start as we mean to go on!

What fun it is turning out to be...

Basically did the timing belt and auxiliary the other week including full coolant drain, major service and replaced the fan resistor module with genuine. All good....

Hi, on our Peugeot 206 (1.4i 55kW, 2005, automatic transmission) the temperature gauge is not working. The coolant temperature sensor was faulty* (no data on the driver cluster, nor on diagnostics) and I changed it. After changing the temperature sensor, the data is shown in the diagnostics tool (Generic OBD scanner and clone of Lexia) but on the...

Are the front driveshafts and engine/transmission mounts the same as a standard 2.0l AMT6 model? the vin no for my 3008 is VF3**************[VIN obfuscated, can be read by forum staff].

Hi Experts,

Two short technical questions regarding 3008 1.5 Diesel - 2019, please....
1. Does DPF module come before SCR in the exhaust pipeline ?
2. Are DPF and SCR two physically separated modules ? (Can I replace one and not the other ?)

Thanks !!!!

Hi,
Peugeot 3008 62 plate 65K miles
I set the cruise control to 70mph and it stays at that speed up or down hills.
If I put the cruise on 'pause', either by pressing the side button (cruise stack) or using the brake/clutch and go down by 10mph (to 60ish) and then just engage the cruise with the side button.
It engages but then the rev's go from...

Sigh.. Im starting to feel like I'm logging in more than Marc ](*,)

Short story: I had engine shake and a few miles later I had engine cut out at about 55 mph. Engine would not start until 30 minutes later. P0087 was the only fault on a simple obd2 scan (and ASR Antipollution fault on display). Drove fine afterwards. Engine still shaking though....

Hi all. Can anyone shed some light on how the rear door latch works? It's stuck in the locked position. I've managed to free off the loop section from the left hand door to open it up but it's well and truly locked on to it. the top and bottom latched all work on both doors so can I assume the actuator in the middle is kaput? Is it fused? could...

Changed the air filter on my 207 1.6 HDi today.
Air filter as you may well know is in a totally stupid place and whilst wiggling the box at the back of the engine, this thing fell off and down the back of the engine.
Anyone got any idea where it should live?

Hi we've got a 208 1.0l 3cyl petrol that's extremely flat on acceleration. Plugs and coils are new, the map sensor is also new. We've got some like readings and the ignition advance can go -10 to +10 degrees instantly. Any pointers would be appreciated.

32A64CEB-D650-4C3A-B245-BE29FF4BFC2E.jpeg
My 2008 307 Hdi 110 displays 'Risk of Particulate Filter Blocking' and 'Depollution System Faulty'.

I am an absolute Diagbox newbie, but a quick scan shows amongst others the error message 'Diesel Additive Communication Error'.

Can anybody please shed any light on what this message means? Does it...

Hi,

I have installed OEM tow bar and electric kit on 208 II from 2021. After installation and connection to the trailer the lights of course didn't work.
I hooked up Lexia to the car, bought a token, used oficial Diagbox, and activated the trailer unit. Yuhuuu, trailer works! (wasn't really able to test the fog light as it was missing on the...

Hello.

I have a 208 1.2 puretech from 2017 72000 miles.The car is in Great Britain. VIN : VF3**************[VIN obfuscated, can be read by forum staff]

1.Could you please tell me what type of engine i have and when I need to change the timing belt kit?

2.For the moment I use 0W30 oil. I've readed on the forum that peugeot recommended a different kind of oil for my engine. I use the good...

Hi all, got a Partner running on 3 cylinders. Turns out injector 2 had given up the ghost. Pulled them all & sent to Darwen Diesels (AMAZING guys :bl: ) who told me all injectors were reading 10 when they should be reading 150 to 190 (not 100% sure of the test, but I assume it's an electrical test as they are piezo). So 4 new injectors posted out...

Hi to all. I have a Peugeot 308 sw model 2011. (9 HP, 4E_4H OR DV6DTED) and I have a error code U1218 , I think it's a generic code, but what can it be? A have a Carista obd with FAP APP for PSA cars from Amazon store and works fine. Thanks for your help and regards in advance

Hi, the on / off button of my Peugeot partner 2017 is not working. The display is working, so are the other buttons on the radio which makes me think it cannot be the fuse. If I twist the same button the volume change shows up on the screen, so it is just on / off press that is not working. Any ideas on how to solve appreciated!

Hi all,
I`m new to the forum, and was wondering/hoping if there are any members with diagbox or pp2000 in my local area (Birmingham) that could reset my additive ecu ?
I have had the pouch refilled by my local garage, but they do not have any equipment to do a reset. I have the error message appearing on my dashboard every time I turn on the...

Hi!

Does anyone have experience with changing the fuses in the Peugeot RCZ (1.6 THP 2012) battery fuse box. I would greatly appreciate it if anyone has a story to share about how easy/difficult it is to access them. Maybe even pictures of the location inside the fuse box?

I have a Peugeot model 2008 for about 1Y (bought it new). There is the start/stop (works all the time) and the hill start assist after the start/stop (holds the car for 2s, to allow the engine to start after the start/stop). The hill start assist works well if the hill is moderate and above. However, if the hill is light, say 4%, the hill assist...

Hi there,
I need to top up my dpf additive and I'm worried about using the wrong grade of Eolys fluid for my 2010 Peugeot 3008. Can anybody advise?
Many thanks
Robert

Before I head off down the rabbit hole of trying to fix my 'P0087 above 3000rpm' problem, can someone confirm that I absolutely positively only have one fuel pump?
I'm pretty sure it only has the high pressure mechanical pump on the back of the engine and doesn't have an electric one in the tank.
Car is a 2008 207cc 1.6 HDi with VIN:...

For the last approx 50 years since I got my licence I have serviced all the family cars, new oil, filters etc plus replacing items as needed. This morning I attempted to change the oil on my 3008 1.6 HDI. Started by looking underneath where I can put the jack to raise it up to put some axle stands, thats when the trouble started, underneath is the...

Can anyone advise me what this 30A fuse feeds please?

Engine bay fuse box on 1.6HDi DVC6.

I’d have thought it should have a nut on it but looks like it has never had one!

Will test it for potential issue but curious as there are some outstanding faults in the ECU which I am working through and the resolution of one could be VERY expensive....

Hello,

I have a 2012 Peugeot Partner e-hdi with a Semi Automatic gearbox, I'm looking for maintenance manuals and tips to look after these gearboxes.

Also could anyone confirm which transmission fluid these take and what are the intervals to change it?

Does the EGC need any maintenance or actuator fluids changed?

Thanks,
George

Hi
Could anybody tell me if it is necessary to prime the fuel system after the fuel filter has been changed and a pair of fuel injectors replaced, as on my engine I cannot see any priming bulb.
Is it somehow self priming or do I need a syphon arrangement to draw fuel from the tank and then push it back through the new filter removing the air, and...

Hi all. I'm new to the forum. Seem's like an amazing resource and I hope I can get some good advice. I hope you all can humour this long post... I thought it best to share everything i know...

My 2018 Boxer van has done only 47k miles (1 previous owner from whom I bought it at 37k miles).
I put it through a major service at 40k miles (I do not...

Hiya Guys!
First of all I wanted to introduce myself, as I'm a new member. That's the end of the offtopic here.
I am a new owner of a 2012 508 2.0Hdi, and I came across a similar problem. One day the park brake failure occured, but after restarting the car everything was fine.
Two days later my father in law was trying to move the car, but he...

My dad has just bought a 74 plate Peugeot e308 GT. Form what I have seen it should come with lane assist and lane keep assist. When he puts cruise control on he gets the bars to the car Infront but not theblines at the side of the green steering wheel symbol.
All safety features are turned on int the car as well. Can anyone advise if Lane keep...

Hello everyone,

I have Peugeot 308 SW II, 1.6 HDI 68 KW and I want to change the oil in the manual 5-speed transmission. Please I have a one question. Where is the hole for filling the gear oil?

Thank you very much!

Have a nice day!

Greetings from Czechia :)

Let me explain

Peugeot 308 SW Gt line, 2.0 blue hdi 150, 71k miles

Recently I had a dispute with Peugeot dealer….long story.

Upshot is, ad blue injector replaced and DPF removed, sent away, professionally cleaned, all good.

I live on the Isle of Wight and this is not the place to own a diesel with a dpf. I frequently get the warning for...

hi friends,
I need your help on the ABS module wiring diagram
Peugeot 580 1.6HDI 2015 manual
VIN: VF3**************[VIN obfuscated, can be read by forum staff]
thanks :P

So my fan blower has stopped working. It's mid summer and we're about to head to europe for a month. There is no aircon in this van so having the fan working at least is quite important.

It's a huge pain to get out (and I suspect even worse to get back in, with a set of not-very accessible clips and having to take much of the dash off to get at...

Hi all,

After almost a year of trying to resolve some issues with my 3008 with a 1.6l diesel (and a lot of time and money spent), I’m getting to the point where I just don’t know what to do anymore. We keep trying to get the car ready before going on a family holiday, to be told it’s fixed, and then inevitably there will be a problem. If anyone...

Hi, ALL

A friend's car has two relevant errors U1113 and the other B113F 15. I found the description of the first error here on the forum and the second error requires an electrical diagram.

Thanks for the help

Hello,I have a pug 1007 and the passenger sliding door doesn't want to slide, you can hear the moter as it closes the door when pushed, tried a reset and also checked the fuses, what could be the issue please,
Any replies Will be grateful.
Cheers Eb

Hi all,

This household could be venturing into Peugeot very soon.

The Missus' Smart failed its MOT and I did all the work. Drove it back to MOT station today and the rear brake pads were really smoking.

I told her it needed new pads, discs (which it did) and new calipers (which it probably didn't).

Anyhoo, it looks like the rear offisde hose...

Hello to all.
We have been off the forum for a long time.
Even though we still have a Citroen Jumper and a 205 td, they have not been our main transport.

That slot is filled by a very reliable 1999 Audi A3, 1.9td and a very UNRELIABLE 2009 Fiat 500 1.2 petrol.

The Fiat has almost broken our spirit so we decided to replace it with something older...