French Car Forum

A couple of weeks ago my master cylinder went. Peugeot replaced the part with no need to work on the clutch due to this being an external part hence no clutch contamination. But since the work I’ve noticed a whining noise from the car when decelerating. There is no issue when selecting gears no clutch slip and no noise on accelerating but when...

Begging for a wiring diagram didn't work for me so now I've belled each wire, and I'm confident I have the wiring sorted.
Next thing: I'm using the standard Bosch ECU but I don't have the transponder/key. I have the clocks but no looms to use them. I have the BSI, but I'm hoping to lob it in the bin.
If I get the ECU immobiliser deleted, the...

Hello
First post on here for me though I have been looking at this forum for a while - probably the best uk peugeot forum in my opinion.
I have the p 0104 and p1351 fault codes - read with a basic generic code reader, MIL illuminated.
Re p1351 I checked the glow plug resistance values and found that two of them are open circuit. Sprayed them...

As per the title really, I'm going to delve into the BoL shortly but on the 206SW we just bought with a cooked engine (got so hot the head gasket is literally burned across the water jacket area & has melted fire rings on 1, 3 & 4) on inspecting it to see whether or not it'd be viable to reassemble with a skimmed replacement head I noticed...

All,

'erselfs 205 ('90 3dr) has the big external sunroof. Tail end of autumn, though, the felt runners within the rails fixed to the outside of the roof skin had a bit of a sulk - and crinkled backwards, jamming the glass. Fortunately, we got it closed again, and it's been watertight over the winter.

But. Spring is coming (he says, wildly...

I got me a cheap OBDII Scanner for my boxer 2.2 VIN VF3**************[VIN obfuscated, can be read by forum staff] and it's throwing out codes
P0094 Powertrain
P0101 Powertrain Mass or Volume Air flow circuit
P0603 Powertrain Internal Control module Keep Alive Memory (KAM) error
P0600 Powertrain serial communication link ( pending Fault)

I've just replaced 3 glow plugs (4th would not come...

I know it's a bit rude to jump straight in with a question, but here goes:
I've fitted a few ES9 engines to things but now have a ES9 J4S fitted to a buggy. It's all in and ready to go apart from the wiring. I have a couple of diagrams that look like they're correct but the cable ID's don't match the loom I have. It doesn't help that I don't have...

hi all, was hoping to have a discussion and some advice on a lead for a project ive debated with.

I have a Suzuki Jimny (not manly, imposing or fast, but those who know, know theyre a hoot!)
I've been itching to have a diesel again though (and yes, I've thought about selling this and buying, but I like the Jimny and a challenge), so I did some...

He noticed one of the plastic blanking covers has come off one of the roof bar mounting points is the ones that cover the chrome bits in the roof. Are they only available at the dealers or is their another source or will other makes do?
Any help or advice appreciated😁

can any one say if the strut top mount is to be stright under the top nut and plate as i took a look if this was being the problem with the squeking behind the dash board and seen the it was not stright so as the car was jacked up i replaced it and ithe squeking stoped for a day or two but it back now

I thought I'd share a recent experience and would like to ask if there's anything I've missed.

Recently I welcomed my 6th Peugeot, a 70,000 mile 10-year old 407 SW 2.0HDi, and I've been giving her a thorough going over and service before putting her to work.

Having had issues with my 406 2.2 HDi additive system, I decided to check the additive....

Hi everyone I'm looking at a prospective car to buy, this is abroad and getting anything decent at a cheap price is a struggle to say the least...

The best car an old 306, owned from new, clean, clearly well cared for, tight to drive etc, but has this in it 🤣

I don't reckon it's k seal, but maybe one of the other brands, or is it some kind of...

any one else had a bad noise coming from behind the dash ,i have had it there now for some time from when i changed the drop links as i hit a pot hole and i could hear that the links had gone and that is when the squecking noise started but since i have changed the links the squecking is still there it only seems to come to life when i turn right...

Hello, I have a 207 and was scanning for codes and this code shows up and I have no clue what it involves/ what it is. u1325. Any help would be greatly appreciated as to get pass my mot I need this code gone. Tia

right i had a new turbo fitted in the 308 sw 1.6 ,well sice it as been done there seems to be a lack of power in 5th gear and some times 6th gear the turbo seems to struggle kicking in the car would do it when the old torbo was in checked maf and cleand ,checked fuel filter ,but have not checked egr as of today any info will be most great full

First post ... saying hello to everyone! 8-)

Hi everyone,

I thought i bought my dream car but so far i
I waisted £1500 on useless mechanics. The patient is:
Peugeot 308 cc
1.6 THP PETROL
2010
Automatic gearbox
Mileage 50k

Since I bought the car I had many issues already.

When I bought a car I noticed there is not hot air in cabin. Also I could smell a cooler while driving.
I opened...

First of i would like to apologize, but the car in question is not a Peugeot, its a Volvo, but it does use the DV6 engine from the PSA group, and i really need some expert advice, so i hope i will be forgiven.

Car starts perfectly, no codes, pulls fine below 3200 rpm, but at 3200 all hell breaks loose, and the engine start juddering, loosing...

Hi

I have a clock in the car and no time comes up it has a part number of 96250976ZR, the bulb is working just no LCD, anything I can do to get it to work before I buy another :mrgreen:

Cheers [-o<

Hi,

I have a 407sw HDI 136, i have had the usual challenging Peugeot problems.

in the last week the Water Temp has gone above the 90c and fans working as they should. there are no visual leaks and the coolant level is correct.
On my way home yesterday the temp went in the Red and the car showed STOP The car Now due to temp.
Before i spend an...

Hi,

First I should come clean, the vehicle is not a peugeot, it is a 2002 fiat scudo van. However it is really a Peugeot Expert and has the PSA DW10CTED engine so I am hoping there are more experts here!

My problem is that I wanted to change the crank pulley as it was rattling but had a real job trying to remove the crank bolt. 5 minutes with a...

Late last year my daughter's car began blowing the 20A starting circuit fuse occasionally when turning the key to start. Replacing the fuse, and no more problems for a time.

This was happening more and more often, and I replaced the starter motor/solenoid in April this year. The car's been fine....until last week.

The fuse wasn't blowing, but...

Hi all, could anyone tell me why a Peugeot 307 automatic AL4 box would loose drive when hot? will drive ok when cool.
2004 with 80.000 on the clock.

Hello Peugeot enthusiasts.

I have a problem with my 207 2007 Peugeot, it just started itself, in the home parking lot luckily,, :)
in gear it hit the house and stopped with windscreen wipers on full
not sure whether it actually fully started, or just cranked itself that one meter to the house.

locked - no remote start, keys in the house

Have...

Hi all, new to this group and owning a peugeot 3008, i've had a number of issues since buying the car, i've had to replace 3 injectors, and MAF sensor within the last week and now have a code U1 325 permanent incoherent data coming from a Gyrometer / Accelerometer sensor not characterised and U1 305 non coherent data from the steering wheel sensor...

Hi me again lol

Just a quick question that has got me beat :(
Vehicle in question is :
207 1.4 59 plate 3 door
Question is where the heck is the fuel filter located, there must be one right :? :? :? :? :?

Vin number is VF3**************[VIN obfuscated, can be read by forum staff].
And yes it is my lads car

Colin

Hei!
I've just replaced one injector on my 508sw 2011 model 115hp. How much tightening torque do i need on the injector holder/forks?

Hello dear members,
Please read my story and tell me what is wrong with my dipstick.

Recently, I had a problem with checking my oil level. The story begins about 7 months ago when I drained engine oil and poured fresh oil into the engine.
The manual says oil capacity of my car is 4.25 Liters. I usually let the oil drain for about an hour and...

I recently bought a Peugeot Partner 2006. I am aboute to restore it at trying to fix most of the problems indicated or found. On of them are a snped cable from the clutch pedal contact. The cable is hanging lose connected to the contact at the pedal and I can nou find where it should be connectd in the other end. How to find the other end and what...

Hi everyone,

I recently bought a Peugeot partner 1.6 HDi 75 2007. It’s run perfectly since I got it and the mileage is just shy of 50k.
It started having some sort of oil leak a few days after buying it, just a small patch (I think it could be the power steering fluid as that was really low)

I went on holiday for a week, came home and it just...

Rummaging through the pile of CDs/DVDs on my shelf I found a three disk set of Peugeot TIS / EPC Service box SB18, thought I'd see if they're still of any use.
Got as far as attempting to install them then got the 'Enter the code' message but I don't have the code, any ideas?

I guess it's cloned stuff from Ebay.

Hi there. Am about to attempt (finally) the replacement of the two main solenoids for the upgraded Borg Warner type, to hopefully cure the wretched 'snow and sport' limp mode problem. I embarked on this last year but hit the problem of how to upgrade the Transmission ECU for compatibility for the BW solenoids. I have now succeeded in doing this...

So my 508 hsas been sitting a couple days and when I started it today, i could hardly get it to rev from idle. It seemed to rev ok above idle, if I kept the turbo lit. I have a soundbite but don't see any way to add it here.
Could it be that the start/stop battery, which is as old as the car(2013) is done and me leaving the car for a couple days,...

Hi all,
Just joined today to try and solve a problem. My 2008 Peugeot Partner 1.4 petrol, just died on me today. No warning, no stutter, just stopped.
The AA man thought that it could be a fuel pump problem and found that there was only 9.5 volts at the pump. He thought that this could be a faulty relay/ECU problem. I was thinking of taking the...

Hi, I've been given the job of rebuilding the cylinder head on this car. The problem I have is it came as box of bits. I've ground new valves in and am ready to fit the camshafts. With the numbers I have on the shafts I can't identify which is inlet and which is exhaust.
1st cam: FLM34 299/
JP41 C325 06

2nd cam FLM 35 284
JP41 B325 06

Any help...

Does anyone know if any of the other french cars share the same fixed point roof bars as the 207?

307?
DS3
208?

Etc etc

Trying to expand my search for some.

Or even better if anyone has any 207 ones for sale I would be interested 👍

Does anyone know how to remove the large plastic moulding across the grille on the facelift 207SW?

Strange occurrence with our Peugeot 308. On our trip down through France the warning for the next service interval started to show on the display. I was fairly sure that there was plenty of mileage left before next service due before we set out and so have been out now to get the figures.

According to the service record booklet I changed the oil,...

Hello everyone.
Recently I have buy a Peugeot 5008 1.6hdi 2015.
Yesterday I have encountered first problem with car. Engin fault repair needed sign come up and car is in limp mode.
With my basic obd2 scanner have I found 2 fault codes :
P1434 and P1435. I know what codes mean.
I have check aditive level (with car diagnostic tool) and there is...

I have just bought this car, so decided to change the cambelt. I drove the car into the garage, put the roof up because I needed the wheel locking nut, but not the windows. I then proceeded to change the cambelt. When i tried to start the car nothing doing, I checked the marks I had made on the flywheel and camshaft which lined up ok. what I...

My wife`s 1999 406 GTX has been on lockdown SORN for four months. Taxed it and got it ready today but the bonnet is stuck. The nearside catch releases the bonnet that side but the offside is firmly down.
Anyone know of a trick to release the O/side catch.

Hi all, I was hoping someone out there could shed some light on this problem.

I have an error message popping up, ...Speed control system faulty When it happens the engine loses power and runs proper ropey! Also, the tick over increases to around 1300 and is very uneven??

When I touch anything on the cruise control stalk the message is...

Hi everyone
I have a peoguet partner 1.6 hdi 2012
First it came up on the dash low oil
I checked the oil and added a little to top up
Then it came up low oil pressure
So I changed the oil pressure switch
Now the van drives for 20 or so minutes then dies
Now says engine fault if I lock then unlock the doors the van starts and drives fine for...

OK so long story short, there's a problem with the wiring on our '03 black 206. The 1.1S to 1.9XUD9TE conversion project so it's highly likely related to the work I've done to the loom ALTHOUGH I don't believe the issue arose for a while after the wiring mods. (I had wipers and no ABS lamp warning until a couple of days ago, then when I turned the...

Hi All
After a long run the idle speed on our 2014 3008 1.6 HDi drops to about 740 rpm (I have a reader that I can plug into the OBD port) as opposed to a normal speed of about 820rpm. This low tick over speed is quite lumpy but smooths out as soon as I touch the accelerator. Is there something on the throttle body that will enable me to increase...

Hi there,
I've a Peugeot 106 zest mk2 1.5 derv 2002,
last week I was at a customers house (sole trader) It was hot so the windows were all down in a private courtyard, I needed to go and get supplies but she wouldn't fire up! Cranking over okay but not firing. (this car is well serviced, new cambelt last year and oils and filters twice since...

Hi, i want toask, are the radiator fans supposed to switch both at the same time? Because at the moment only one is switching on. I tested the non working fanby wiring it directly to the battery and it is switching on.switched relays from workjng fan to non working fan still it doesnt switch on. Any ideas?

My wife's car is the 207 CC, 1.6 Vti petrol model on 08 plate.
We've had it for a number of years and it has generally run well and is at 100,00 miles now.
It has recently started to run rough on start up idle although it revs up smoothly and runs evenly going down the road. Yesterday though, when warm, it cut out at traffic lights etc. but will...

Just had a Hunter 4-wheel alignment check after some brand new tyres and here are the results:

I'm no expert, but I believe them when they say the front needs adjustment. They've quoted me £50 for that. The rear apparently also needs a minor adjustment, but they said that the bolt looks so frail that they won't risk it without replacing it...

My car's boot light switches off only after locking the car. All other time, it will be ON evenif Boot door is open or closed.. is this normal in Peugeot 308 THP 2009 petrol cars??