French Car Forum

For my 2008 307SW 1.6 Hdi (110) I have a pair of new rear brake caliper carriers Part No's BDA431 & BDA432. I was expecting them to be obviously handed, but having taken them out of their packaging they look now identical to me! Without the part numbers BDA431 and BDA432 stamped on them I can't tell which is for nearside and offside. How do you...

Hello,
Someone tried getting in to the van and theyve damaged the back door lock and handle.
Does anyone know where I might get hold of a replacement?
It still clicks with the fob but the outer rear handle has gone altoghether looks like the barrel had been drilled.
I'd need a handle with a barrel in it I think.
Ive looked on ebay (supposedly) but...

Hello,

I have these two codes pop up every now and then (and car goes into limp mode). How likely is this a result of a malfunctioned throttle body rather then electric harness or BSI ?

After clearing the codes the car comes back to life and it takes days or weeks before the faults pop up again

P2101 - control of the motorized throttle motor...

Hello. I have a Peugeot 207cc GT THP150 with the EP6DT engine and I've just replaced the turbo oil feed pipe. For some strange reason my battery warning light has started flashing amber when I turn the ignition on and stays flashing amber when I start the engine but there are no fault codes. It was perfectly fine before. Any idea what to do...

2017 3008 Fault codes P1434 &P1435 additive system
Tried filling tank still faults present bleed system and prime still faults
New tank and pump fitted, What is the procedure for now programming the tank / pump
To system with Peugeot partner tool
Thanks Joe

Our sliding door handle has been wobbly for a while, and gave me quite a surprise when it pulled out of the door in my hand! Turns out theres a 'wear strip' on the end of the handle that has come off. I dont know where is has gone. Probably down into the bottom of the door. It looks like it slides onto a kind of dovetail on the end of the hande....

Hi all, I had the diesel particulate fluid message pop up after putting some diesel in a few days ago. I'm not sure which fluid my car needs and I'm not sure if I have a tank or a pouch. I work nights and long hours so I don't really have time to get under my car to check until my day off on Thursday and I've got a long drive next week so need to...

Hi All,

I have a 308 SW 2013 plate, and I wondered if I could install a cruise control stick on this easily?

I watched a YouTube video - It seemed to be very straightforward, however when taking the plastic trim off, it is clear that the brake and clutch configuration is different and I don't appear to have the wiring as laid out in the video in...

Hi my 308 has been eating aux belts, I have found the issue, the tensioner is held in place by two bolts to the block & a third to a mounting bracket. This bracket is cracked, I can't see how to replace it without total dissasembly so a parts diagram would really help. It's the lower of the two tensioners. My VIN is VF3**************[VIN obfuscated, can be read by forum staff] many thanks

Evening all,I need a little advice,so basically my Peugeot 207 is having a little issue I recently had a new water pump pulley and thermostat fitted mechanic said that once engine gets to 90c it drops down to 0 then slowly creeps up to 70c and drops again,he said it could be down to a faulty ECU as he said there is a little water ingress on the...

I’m looking to see what make Peugeot use for their suspension springs. I have replaced the spring & top mount but still getting a spring noise when turning.

Vin: VF3**************[VIN obfuscated, can be read by forum staff]

A friend of mine thinks it’s KILN but don’t think that’s correct.

Hi Guys,

DW10 2.0 hdi, 30k miles, done head gasket but did not check the thichness of head gasket, took it as standard (one dot ) , if there is such a thing?.

is ther anyway to find out what the original one was on production?

looked at 4 other engines and they are all 3 dot ie 2 thickness up from the starting point of 1 hole.

vin is....

Hi!

So I have a 2005 307 1.6 petrol (TU5JP4) on my hands that overheats. Car is sitting in a parking spot at the moment, not ideal for major mechanical work.

From a cold start, the temp gauge suddenly jumps from coldest to max temp after about 5min on idle, turning on the STOP-light. At this point the cooling fan kicks in and runs about 5min...

Hi All,

I am new to Forum and beginner in the car space.

Can anyone help me to identify if those rear brake pads are okay to pass MOT? and do I need to change it in the upcoming month?

Thank you!

Hi All. I haven't been hibernating, just very busy with a roof top solar electric and water heating project on Pint Pot. Our 3008 has been getting an odd steering vibration on acceleration only - it goes away when you lift off and is reduced when on part throttle. It started about 6 months ago and got slightly worse with time. I checked bushes,...

Hello all,
I have a Fiat Ducato 10 with the 1.9TD engine.... (1999) :oops:
I believe that quite a lot of the parts ...including gearbox parts are interchangeable with some Peugeot and Citroen models?
Looking through this and other forums it's clear that the gearbox used in the Ducato (and others) is prone to malfunction and even failure. Cheap...

Hello,
Sorry for my lack of input but life seems to get in the way of everything right now.

We seem to be going through a bit of bad luck at the moment and to cap it all the car flashed multiple faults up this morning.
Handbrake fault, gearbox fault, abs etc etc. The handbrake was working ok but I was limited to 1, 2 and 3 gears only and it...

Hi al,

I'm new to the forum, so hopefully this goes in the correct topic!

I've got a Peugeot Partner 1.6 ehdi and have recently fitted a new engine mount (top) and ever since, for the first few miles (presumably until things have warmed up) there's a pretty loud resonance from 2,000 revs upwards.

It seems to be thrumming through the bodywork,...

Hi,

I have Opel Corsa f (PSA Based) ? wanna change the parameters, cornering light etc. And ? wanna footwell light thank you ?

sometimes i notice a tick noise from driver side of the engine but only does it every so often

is this normal on theses mini engines or is it a sign that my timing chain is on its way which i thought if it was chain it make the noise all the time and i no eml light

Bonjour fellow French car enthusiasts,

I'm here today seeking some advice and expertise regarding a bit of a hiccup with my beloved 2009 Peugeot 607. While I've been enjoying the elegant ride and comfort it offers, I've recently encountered an issue that's left me scratching my head.

Lately, I've been experiencing some irregular engine...

Please help!

Considering doing oil change by myself, got hit by 1st problem, jacking point.

I understand the there is one jacking point stated in manual, but I need another point for axel stand. (front of car)

the picture attached shows the correct jacking poing - U shape brace with o ring. However, I do need another point to either jack up the...

Hi everyone,
Car in question:

2008 308 1.6 petrol with the AL4 automatic gearbox

It's a family members car and trying to help them out. Yesterday they got stranded, gearbox faulty message appeared on dash, put it into drive, press the accelerator and the car would just rev but not actually move. I disconnected the battery, reconnected and it...

Hi all, new and looking for advice please. Sorry for the long post!

I have a Peugeot 308, 2018 1.6 HDI Auto, and recently developed a problem while driving on the motorway. The car has a full Peugeot service history, last serviced 4,400 miles ago, total mileage is 80,500, so quite high for it's age.

I was doing approximately 70 mph, when a big...

Hi All

So the 308 project car continues. We took it out for a bit of a thrash and managed to trip a P0299 Turbo Pressure too low, as per below at 5300 rpm, foot hard down just at the 4th/5th gear change.

Capture4.JPG

So I've looked over the system and it seems ok , traces as per.. Requested v Measured except it couldnt quite make it at the...

Hopefully someone might be able to help with a couple of questions regarding the EAT6 gearbox and an issue that I am having with it. The gearbox code is 20GE13.

I have 2018 Allure S/S automatic petrol car (c 35k miles) that has recently developed an intermittent fault with the gearbox where it occasionally gets stuck in limp (3rd gear). The code...

Hi,
I got a replacement fuse box BSM with relais-set built in by my independent workshop in the end of `22.

Job has fixed missing action of the washer pump for windows, although different from before, as the front switch now serves front and back wiper at the same time, with halv pressure obviously. :)
Did not use AC all winter after this job...

Hi. Still doing jobs on my wife’s 207cc.

The drivers door window Temic unit needs replacing. I have a new unit and can access etc but it has the power wires going in that are held with a very French looking connector that I don’t want to break

It looks like you pull up but then not sure what to do with them after that

Can anyone tell me?...

Hi All

First time here but longer time Peugeot owner. So what I have is a 2013 308 1.6 THP Vin: VF3**************[VIN obfuscated, can be read by forum staff] 6 speed auto.

So this car was a bit of a wreck to start and we got it as a bit of a project car. So far, off the top of my head, its had a blown head gasket replaced, new turbo and associated plumbing, new chains and tensioner, VVT...

My 2008 307SW Hdi 110 has 30mm diameter stub axle, please can someone advise correct torque setting for rear disc nut which is M28 (Peugeot 373932) and requires 36mm Spanner ? Thanks

I am coming to the conclusion its 300Nm but if anyone can confirm that would be great 👍

Hi all

I need to replace the rear hand brake cables on my 807 (2007). Can anyone point me in the right direction for instructions. I can do normal brake changes and believe the cables should be straight forward, but need some guidance.

Thank in advance.

Hi newbie here. I have been and said hello on my other post.

My wife has a 207cc with an ongoing brake light problem.
The car has at best intermittent brake lights that often don’t work at all.

Have replaced switches many times and often works for a short while but then back to the same routine.

Also sometimes work when you stamp hard on...

Hello all,

Anybody experienced this fault because after clearing this fault later on it appears again.
It is in the BSI 2010

B1808 87 fault in the unlocking of the immobiliser by the ECU

Even with this code everything is working fine no problems whatsoever but still what is this fault and how to solve it ?? Anybody that can point me to the...

Apologies if this has been done to death but please forgive a newbie.
I bought a damaged 2016 RCZ and purchased second hand xenon headlights ( as was fitted in factory). Both headlights illuminate perfectly, but The issue I have is the driver’a side does the up down left right self-rest when starting but the passenger side only does up down....

Hey!
I thought I'd ask here for help with a problem with my car. The car is a 2007 registered Peugeot 307 SW. The engine is a 2.0 liter gasoline engine.
The car suddenly started to indicate an AntiPollution fault on the screen and the engine fault light came on. On the testers, the only fault code that appeared is code U1218. Is there a...

Hi,

Having repeated issues with my turbo cutting out. Cut out recently and cleared fault codes but would cut out weekly- engine management light shown so took it into Peugeot specialist and below codes shown;

P2600 turbo cooling coolant pump control: open circuit
P023C control of the coolant pump actuator: short - circuit to the battery plus...

Hello,

I have a Peugeot 406 V6 Coupe with the ZF 4HP20 auto box. I've been doing plenty of reading but I can't quite find a consensus on the internet as to the right angle of attack for dealing with my problem...

I've got the Sport/Snow lights blinking on the dash, 'automatic gearbox fault' warning on the computer and the transmission locked in...

Currently 10 out of 16 tappets are stuck . That means they don't move if you press on them. Now I'm not sure if that means they are full or empty of oil. However, how should I prime them before I put the cam carrier cover back on. Should they all be able to be pressed and be springy ?

Hey everyone, I need your help.
My TCM is officially defected and I need a new one. In my country Lebanon I couldn’t find one with the exact same codes on it, although I found a couple on the internet but unfortunately they can’t be shipped to me.
So 1) anybody knows someone having this exact module that can ship it to me?
2) My mechanic thinks...

Hi, I have this problem and I don't know how to solve it, can you help me. When trying to calibrate just get failed. On live date the angle sensor is not moving with the new or old sensor fitted, it is just stuck at 5774 degrees to the left, I have just had the van back on diagnostic and have found the following fault codes in power steering -...

Hi all.
I hope you might be able to help.
I had issues with bogging down on acceleration, in my 2007 Boxer converted campervan, 5 speed manual. Particularly part way through longer journeys. But this was intermittent.

The first garage replaced the egr valve and fuel filter. This lasted maybe 6 months if that until the same problem occured.
I...

Greetinngs from down under!!
Synopsis: I have lost a part (x2) that appears to be a) critical and b) unavailable! Naturally I would value advice - especially suggestions of where I might score a couple of these (but also on whether they are 100% necessary). The PSA/Stellantis part number is 352503.

The full story: My 406 (it's a D9 SV, but it's...

Hi,

I got P1755 fault code on my ETG5 Peugeot 208.
Then i tried to drive but (both engine fails on the screen is on, and service fault is on) The car perfectly changing gears to up like 1-2-3-4-5

But never down, you can not downgear on manuel mode or in automatic mode. But if you go for N after D it changing gears. I mean if you are going with...

So I have a T9 engine oil leak. I’ve had the crank shaft oil seal replaced as it seemed to be coming from that area, I’m at a loss to what is going on I’ve attached a picture. To the right beside some black plastic you can see clean new oil.

Anyone have any ideas?

IMG_4181.jpeg

Hi all new here I have a 307 2006 with 27500 miles on it have a problem with the air doser well I think that’s what it’s call please see pic . Car all runs fine no engine management light on when I rev the engine and it settles back to tick over I get a rattle from the air doser I have marked the area where the rattle comes from any help would be...

Hi
My wife’s Peugeot RCZ has had its locking wheel nut key damaged by the tyre fitters.
I have removed all the locking nuts except one and wondered if anyone happens to have the correct locking nut key to remove just one nut (I will happily drive to you)

The code is: E 7DXO

many thanks

:cry: For a few days I have had problems with the lack of power in my Peugeot 5008 2.0 hdi. I put the tester on and the following errors appear:
Car Scanner ELM OBD2
DTC report
Selected brand: Peugeot

============1==============
P2562
Raw code: 2562
ECU: Engine control unit
Status: Confirmed
Turbocharger (TC) boost control position sensor -...

Peugeot partner , just cut out on tickover diagnostic showed under bonnet fuse box faulty and not sending power to ECU , so changed it for one with identical numbers and still won't start ,! But diagnostic now says starting not allowed can anyone give me a clue what's wrong many thanks

Hello everyone from Greece. I want to apologize for my bad English. I have a Peugeot 208 2017 1.6 bluehdi 75 hp. January i did a dpf clean. The next day i took the car in the national road and adblue check engine and key lights came up. Until now nobody can tell me what's the problem with my car. I have erased the codes but every time i got my car...

Good morning, I'm having some electrical issues, it started with my car going dead 30 min after I had switched the ignition off and locked the car. Not beeing able to unlock the car with the remote, And clock always going back to 0:00. This still continues but now I have another isue, 2 to 5 minutes after I switch off the ignition, my headlights...