French Car Forum

My lights are not working properly
One side is fine.
Other side dip beam working not main beam
Fuse ok bulb ok .There is no power to the fuse.
I've been told it is the fuse board.
Does any one know if this is correct
Peugeot 206 cc 1.6 tdi year2005

Hi all,i am seeking some advice on deactivating the ebs on a picasso 2009 mk1,i am going to change rear discs and pads hopefully this week
I have got diagbox,my question is,in diagbox i see two options to put brake into release mode either removal of cables,or removal of the
actual ebs motor,I have a workshop manual,but it just tells me to use...

Hello!

Have never posted before, but have gained so much help here in the past from reading others.

I have a 2011 Citroën C5 hdi 163hp.
180000km, have been running great up until lately. I have orange engine fault in my dash.

Checked out the faulty codes and gets the following:
P107a
P1497
P2562

It said something about low turbo pressure and I...

Hi, new member, first post. I have an intermittent diesel knock on my 2007 Berlingo DW8 engine with the Lucas pump. Starts perfect and idle's well but with faint knocking that gets considerably worse with a few revs. It's the same cold or hot but cleared for a bit when I cracked the lift pin injector nut but returned after a half mile only to...

Hello
I installed Diagbox 8
I had 702 working with Citroen C5

I did activation of 8.01

I can connect to c5
Vin shows up correct and i put RPO code .

and then Diagbox and Lexia are been Deactivated

can You help me

Hi guys not sure which to get, Can you help don't want diags just yet. But have a Haynes and i think there could be something better.

So I was thinking Emanualonline or Service Box from Easy diagnostics..

Any tips greatly appreciated.

Today I fitted a new DPF to my 2012 Citroen Berlingo van. It was showing 100% cinder value and the maximum amount of Eolys had passed through it.
I cannot for the life of me find out where in Diagbox you tell it you've fitted a new one.
I have programmed in zero for the amount of Eoly fluid injected in, but it's showing 73% cinders and the mileage...

Just wondered if there was software that emulated Lexia, diagbox etc maybe by using VMware rather than buying a clone unit?

I have a 2010 Relay 3 van that I'd like to be able to do simple diagnostics on.

I've used BMW diagnostics software on wifes car and have various ODBI cables to USB and ethernet for different models and also ELM bluetooth so...

Hi all, My current laptop with diagbox is dying so I'm installing onto a newer laptop. Easydiagnostics kindly sent me latest software download yesterday but I keep hitting an error about 75% install.
Here are screenshots

diagbox image 1.jpg[/attachment

diagbox image 2.jpg

I retro fitted windows xp to the laptop and only plan on using it to...

Hello All,

I have used my full chip clone with a hp compaq 2510p and I thought to upgrade the laptop. I bought a second hand lenovo t440 with i5, 8gb ram..well more powerfull than compaq.
The issue is that the diagbox is not working on the new laptop but on the old one is working without a glitch.

On the new one I have installed win7 x86 and the...

Dear colleagues,

could please someone advise me, where do I need to go in Diagbox to change the type of alternator on my C5 X7?

I am quite a newbie in terms of Diagbox. Lexia on my XantiaMk2 was a bit easier ;-)

Thanks a lot!
Karel

Today I have looked at diagbox dpf parameters and there is something strange.What means Average mileage for 5 last regeneration manoeuvers - 123km Is that mean that car doing regeneration every 120km?Is that mean its cloged or?

We're back in the UK and I now have time to work on the 308's misfire but before that I need to decide what to do about my Diagbox version.

At present I'm on 7.57 which seems to be fine for my 2013 X7 but a little lacking for our 2015 308. It reads most things on the 308 but has to be prompted for ECUs it doesn't natively recognise. I therefore...

Hi,

When activating the Citroen documentation backup and pointing on Xantia the selection buttons between Xantia and Xantia II are far away from the Xantia and when trying to move the mouse cursor to one of Xantia or Xantia II than all of the buttons disappear. In order to make it operable the selections buttons should be dropped right next to...

ok here i am again #-o

i've got a GLD 1.7/1.8 205 diesel xud

when driving normally the fan has started cutting in and i cant work out why

feeling the rad its hot just as it comes in to the Radiator (top right hand side looking at the car externally head on) , but cold at the bottom and left hand side, was thinking thermostat but the pipe going...

Can someone help me choosing the correct Diagbox - PP2000/Lexia for my peugeot? There are so many on eBay i dont know which one to choose and which is best.

I recently visited the dealer to get my problems solved but figured that i want a diagbox myself that can do mostly the same so i dont have pay a fortune for the dealer to click on 5 buttons...

After all the success with the van the laptop died this morning. Just re-installing diagbox onto a spare. It's up and running but won't automatically update to 7.02, it's stuck on 7.01. Due to this I haven't risked doing the updates to 7.57. Any ideas anyone?
Cheers

Hi Guys,

It might not be the best thread for this topic, but I'll write here anyway. I'm working on a project that requires a swap from manual, lever operated handbrake to an electric one. I've decided to use a Bosch unit that is used in several brands from PSA group. I bought a used unit from Peugeot 3008 MY12, but as I based my wirings on the...

Carrying on from here:

So basically it does not communicates with any control units other than injection and suspension. (The car is 2006 C6). Tried pretty much everything. The thing is it worked before a service visit to a (useless) dealer. Now it doesn't.
The following is what PSA interface checker says:

The only possibility I can think of...

Just wondering why we would buy a Lexia3 from EasyDiagnostics (ED) over somewhere like eBay or one of the direct from China sites (Alibaba, dhgate)?

Looks like the hardware is the same as better eBay sellers and provided the firmware and version is the same what benefit is there buying from ED?

V. 7.83 seems to be the latest available on eBay,...

I got an email this morning from them offering a new multi vehicle Actia diagnostics tool, looks interesting, has a video of sorts on their website.

Shy about the price, need to log in and ask.

Hi all,

Nearly there with this BUT support for Windows 7 ended on 14/01/2020 so I'm left wondering why the drivers won't install.

The Lexia is lighting up.

I can't seem to locate the old PSA Interface Checker that was on the original discs (basically because I cannot find any of my kit other than the lexia and two leads...)

Jim kindly sent me...

I've owned a Lexia since 2013 and used it twice maybe.

Unfortunately, the laptop I installed the files on. Well, should I say, Jim at EasyDiagnostics installed it on, has gone to latop hell for its sins.

I doubt I will be able to find the installation discs by the weekend and I have a feeling the issue with the car, may not be just the double...

Hi, had a 307 2.0 HDI 90 for for five years without issue. I now have 307 1.6 hdi that started to cut out & then wouldnt start. Diagnosed as u/s tank sender which was changed. Now car will turn over & fire for a few seconds & then cut out. If I hold it at 2000 rpm or above it will run, as soon as I take my foot off it cuts out. Code was p0088,...

Hi ! finally i got my Lexia/Diagbox/PP2000, and i've prepared a laptop dedicated to it.

First experience with Diagbox was good, it worked immediately (Win7 32bit machine)

I have also found some faults to check, some are curious to me, like this one :

BSM : Engine relay unit
Response data
R618B964380218000139659741880060CFFFFFFFFFFFFFFFF...

Hi guys I'm in need of someone who can remotely install the Diagbox/PP2000/Lexia software onto my laptop before I throw the whole lot in the bin!!
I'll happily pay for the service as it has now beaten me!!!
I've got a laptop with Windows XP on it using VMWare as a host.
I've installed everything and had it connected to a vehicle where it found...

Hi all

I am having a few issues with Diagbox following install. I’ve looked through the forum but can’t find anything that appears to help.

I have purchased a new VCI, full chip revision C, I’m running a Windows 7 laptop with no previous versions of lexia/Diagbox ever having been installed. I have installed Diagbox and all updates up to V07.58....

Just bought lexia3 pp2000 diagnostics cable.
Spent whole day installing updating Diagbox software, and apperently v8.46 is the one which already accepts this unit, when trying to configure headunit parameters, program is trying to access psa servers. On forums some say that 8.15 was made to connect avoiding psa servers, but this version doesn't...

Hello, I'm trying to install Diagbox v.7.855 on my laptop with windows 10 64bit.
I've bougth this version from easydiagnostic and the programm works (on a virtual machine with windows xp) but I can not connect the actia device because windows 10 doesn't recognize it. (attached a photo with the message shown by windows)
The Actia device is a copy,...

Afternoon all,

I was wondering if some one could advise on the removal and replacement of the rear light unit (fixed to the boot) on a C4 Pic 2014 Exclusive (B87) please.

This is the standard 5 door version NOT the Grand Picasso version.

Many thnaks
Zane

Hi Marc

Please accept my apologies if this is posted in the wrong section
I have successfully re programmed the sat nav / radio to my Vin number (although I don't know how lol)
No annoying bleeping!
While browsing the screens I noticed that different options are activated and deactivated
Would it be possible for someone to see what options can...

Sorry I mean definitive.

Was going to post this in the general forum for Citroen but then thought perhaps here is best.

I would love to understand electrics a bit better.

After changing the thermostat on the Xantia X1 yesterday I started the car this morning and was driving along and noticed that, since starting the car, it appeared that the...

Hi all,

I've a very old laptop running lexia/diagbox which i bought some years ago. As laptop is on its last legs I got hold of a newer one and loaded windows xp.
So far so good
I've loaded up lexia/diagbox from original discs but hit a brick wall. Its asking for an activation key. Its been some years since I installed it on previous laptop and...

Some years ago I bought on Ebay a set of 4 data dvd's which were described as 'Citroen Workshop Manual' This turned out to be a copy of what we would now call Citroen Service - with Docbackup and Sedre etc. It has served me well over the years and allowed me to find part numbers, workshop manual info and wiring diagrams for my cars. The only issue...

Hi one and all,
I have had the car,2996 model since 2012 and it has been a great car.Reliable and cheap to run as you all know,I think.
Unfortunately 2 weeks ago the wife filled it with unleaded.Spent $60to drain tank etc,no idea if the fuel filter was replaced but I presume it was.
Car come back fine and ran well for about a week but now it's a...

hey fellow lovers of french cars, i'm very new to the world of diesel cars (i ride bikes mostly but its cold out)

here is my first post i have a 1.8 205-D GLD 1994 THINK ITS XUD7..
i have been looking for information to get my car started it runs lovely when it starts but the other day i went out in the morning and it just cranked and...

Hi All,

Under what part of the global search is the tpms ecu located. Is part of the BSI under ABS ?

I want to disable to TPMS meantime.

Kenny

I mean a NON remote key, they have both transponder and an electronics board. As far as I know the transponder works on it's own and is powered by the RF signal from the cars transponder. So again what exactly does this PCB do?

Just a note of thanks and recommendation for Easydiagnostics.

I have just ordered the full Lexia kit with laptop, I have been in contact with them with questions etc all week and they replied almost immediately with all the info I needed.
Excellent people to deal with and also a FCF Discount.

Steve

Hi All

I fancy a full diagnostic kit, I have a Delphi and WOW system but the functions seem limited on my Citroen.

What does anybody use or recommend

Thanks

Steve

Hi

I have Diagbox installed up to V7.83. Just wondering what is the most recent car year that version goes up to. Been a while since I used it, I think the disks that came with it have later revisions but they were less reliable to install as I remember?

Thanks

Hi All

I have been using Peugeot Planet for a long time now and decided that I should upgrade to Diagbox. My interface is Rev B so can only go to 7.58 until I replace it.

I’ve installed and activated ver 7.02 but when I start the application I it opens with a black screen with the icons across the top and in the centre of the screen it just says...

Hi all,

can someone advice where the security code is stored on a Lucas EPIC diesel injection system.

i have just installed a XUD11BTE (P8C) engine from a citroen xantia onto a 406 body and it wont run.

Technician says i need a code for pump but i cant see a memory chip on Injector pump diagrams i have come across.

Im not that good with...

Does anyone know of any decent but inexpensive scan tools that allows you to programme cars? I found a Foxwell NT650 for £80 but apparently despite being a good tool it doesn't support programming.

I'm sure I read somewhere that the Lexia clones can't programme either which is a shame as I bought one a few years back!

Please, would someone briefly describe (single syllable words only) what a Lexia is and what is diagbox?

So I got diagbox 7.58 installed after a few tries. I actually tested it out on my PC first which has windows 7 64bit, and it all installed, again after a variety of errors. I thought I didn't work on 64bit OS's?

So my final question before I try and program these keys is, do I have to upgrade the firmware on the lecxia box, I believe I need...

Hi there,
I have bought Lexia3 PP2000 Car Diagnostic Scanner with Diagbox V7.83 Software for Citroen / Peugeot, PP2000 / Lexia-3 Interface from Amazon.fr and I have problem with installing Lexia3 v45 as there is missing file or something like that. I spent my last few days looking for link to download Lexia 3 software with no luck. I contacted the...

got this download from easydaignostics, though i am having problems with install. i get unto 20' 16 secs of video and when i try to run the EXE file it comes back with !!!!! cannot find setup.ini now this i don't understand because it is right there in the list .? so i also notice there is a patch is this possibly to do with the problem i am...

Or can you just install a version such as 8.55, or how does it work?

Hello

I'm wondering the exact procedure to program 2(virgin) keys with lexia/diagbox, I have no spare/originals. A remote and non remote key. I have security code.

Do I plug in lexia obd2cable(which will be connected to laptop) first then put the non remote key in ignition. I then navigate to the key programming section in diagbox and select 2...