French Car Forum

Hi, oil in the inlet causing rough running on my Mi16.engined Murena.

Where can I actually get a replacement PCV valve?

Tried all the usual, but not listed or in stock. Surely this is a service part?

HELP!

Good morning all,
Owing to the notorious P20E8 fault, I'm looking at repairing or replacing the urea tank on my 2017 308 SW.
The present tank has part number 12674101 and I believe that if I do a like-for-like replacement, no reprogramming will be required.
Unfortunately, the only used tanks I can find at present are labelled P1002559/p1001677...

Probably silly question but maybe covers more than my specific vehicle so someone may have input..

I found myself in my little 307cc going through a dirt track with a few puddles and holes the other day. Due to insufficient surveying of the route a mile ahead on my part, I got myself into a point of no return and a relatively large puddle (would...

Hi all
Apologies if this was discussed before .

I have a 2011 5008 2.0 Hdi Automatic and I would like to do the timing belt abd water pump and have few questions.

1- car is automatic , do I still have to remove starter motor to lock the flex plate( with locking tool to teeth or round pin inserted like manual box )?

2- what are torque settings...

Hi, I am looking to buy a Peugeot 308 HDI and I have two possible candidates.

1 - 2014 HDI 92 cv with 50000 miles

2 - 2014 e-HDI 115 cv with 72500 miles

What would be the best option? Which engine is more reliable?

Thanks!

Hi I have a peugeot 508 vin VF3**************[VIN obfuscated, can be read by forum staff].
My rear tyres were severely worn out from the insides to mid suggesting high negative camber. I would like to know how can I adjust this?

i have tried to adjust the bar shown in the picture but it led to the wheel (toe in). The back side of the rear tyres positioned outwards while the camber looks...

I have a 1994 Peugeot 405 le mans that has sat for many years and wont start.

It has an immobiliser keypad to which I do not know the code, however when I turn on the ignition the keypad shows a solid green light. The car will crank but wont start.

I also have no central locking functioning. If I press the button on the keyfob nothing happens....

Was all ready to re-ring the lump(123k miles only as well) because of pressure and smoking at the oil-filler, based on compression tests of course. Did tests and all came in within 5% of 380psi. Car shows absolutely NO symptoms of ring wear or valve problems, uses no fluids, doesnt smoke either hot or cold and goes like stink. Turbo fine, CCV...

Help! Does anyone have any experience with the rear coil springs of a 307CC 2.0 hdi (sport)

I appreciate the parts service is out of action but maybe someone can confirm my trouble.

Was refreshing the back half of the car so changed bushings, awaiting shocks (lower bushes are getting bad) and top mounts and wanted to swap springs too. That's...

Hello,

I have a 2013 Peugeot Expert 2.0 hdi Tepee that has started to idle at about 1250 rpm, but if I press the brake pedal, the revs drop back to normal. Also if I switch the engine off for a minute or 2 it seems to reset itself. Sometimes I can drive for about half an hour before it starts doing it again or sometimes it will only go for 10...

Hello learned people! :)

After the auto electrician repaired the cabin blower fan in my D9 1999 406 a few months ago, I noticed that the heated rear window was turning off almost immediately after being turned on. He replaced two parts as pictured below, plus he did some repairs to wiring.

I've done a search on this forum and I came across one...

Hi all new to the forum ,i have a problem with my turbo actuator on my Peugeot Boxer L3H2 2.2 2014 ,it puts up 2 codes on diagnostics which are PO244 AND POO46 i had guy come out to check on diagnostic machine with a live data , he told me the turbo was working but actuator was being intermitant which over 3 thousand rev would throw up engine...

Help
Unfortunately, I'm struggling to repair my car! 😫
While driving, it makes strange sounds (video in the link).

The sound was like something was in the vacuum pump – replaced it, no luck!
Then I replaced the turbocharger, still making noise!
Using the program diagbox FAB regeneration and it stopped, but after a few KM it came back...

Apologies if already asked and answered. Peugeot 207 SW 2013. Having radio issues, fitted new head-unit double and triple checked the wiring even installed a Bluetooth unit behind the head with ferrite core rings as was experiencing interference. as the weeks have gone on am getting fewer and fewer stations on both normal radio FM and DAB. should...

Hi all,

I originally posted here ( assessing my options for a replacement or AdBlue tank fix. I ended up picking up a cheap second hand tank from a similar age car, since right now I don't have the time to be fiddling around with pressure sensors.

I've fitted the tank, fired up Diagbox 9.150 and when selecting to option to tell the car it's had...

Hi, my Partner van, 2021, (HDI 1,6 Diesel) Electronic Parking Brake started acting up a few days ago.
I was getting a warning message on the screen (EPB malfunction, take to service), dashboard parking/brake icons illuminated and parking-brake button flashing.
After fiddling with the switch several times, and switching the engine on/off, I would...

Hello, the car is Peugeot 508, 2011, 2.0 163HP. After starting a car, sometimes immediately, sometimes after few minutes of driving a lot of faults appear - most of them about Intersystems CAN (communication fault with ESP ECU, One of parameters present in BSI datastream is invalid, Loss of communication with the ABS/ESP module, Speed of rotation...

Hi,

I have a Peugeot 308 2018 1.6 hdi. I recently had an injector repair done. Now when the car reaches around 2000 rpm there is so much vibration. Very little to no vibration in 1st and 2nd gear but 3,4,5 and 6 gears I can really feel it. Any idea what might be causing it?

Can anyone point me in the direction to where the fuel rail pressure sensor is, please, with an Image or a workshop Manual

Info urgently required

Thank you in advance

Paul

206 1.1 2005

Anyone get any ideas on which wires could be causing this problem.

I replaced the ECU, BSI and key as the car was not starting. However, I still have the same problem, and garage and RAC are not able to get anything from the diagnostic port.

Hi all, that's my first post on the blog, happy to participate.
The thermostat related issue for which I'm seeking help is the following.
I own a Peugeot partner tepee petrol 72kw 1.6 from 2011.
The car had worked fine for years with engine temperature between 80 and 90°C.
Recently I got it to an authorised Peugeot workshop for checking some...

VF3**************[VIN obfuscated, can be read by forum staff]

Hi, My daughter (informed me after the fact) that she hit something on the road which scraped under the car and then the engine light came on. I did look under the car and could not see any obvious damage so may have been a coincidence. I used Diagbox to find code which pointed to NOX sensor but was intermittent so when I...

hello everyone, I have a problem with a peugeot 407. the cabin fan does not work. that is, it works the same as in the video, what could be the problem?

Hey all,

Diagbox tells is giving me a fault code that I'm trying to clear from my 508. Details are as below:

HDC : Controls under the steering wheel
Response data
R62F080966566677700249675926077050C0502000165114499
State of the ECU: COM2008P
Reference 1 : 65114499
Reference 2 :
Faults present : 1
B1836 : transponder aerial fault
Characterisation...

Pegeout 208 kicks the fan when I start it and does not accelerate and it shows the engine check light on the dash board.I tried cleaning the throttle sensor and put it back but still the same issue happens.I don't know what could be the problem

1st post, at a loss with my Peugeit 207.
Its a 12 plate Sportium with only 36000 miles on the clock. Immaculate condition and was 1st car for my daughter.

Car passed the MOT 2 weeks ago and when i went to pick it up the car was refusing to start.

Eventually got it started but lights and wipers were operating, in synch, on their own without...

I was able to understand that Lexia3 is a hardware, a cable device itself that is.
And I understand these are clones of original PSA diagnostic device.

But this device has something about versions V9.91 and V7.83 and then lite vs full gold board something.
Then something about rev B, rev C.

What is this all about ?

I don't even know how to...

Hi everyone.

Recently I changed my transmission fluid on the gearbox and the oil i used was MOTUL Gear SAE 75W-80 Technosynthese. The reason for doing so was because it felt like the transmission wasnt changing gears in a smooth way. After the change it became night and day difference. Especially going from around Gear 2 to 6. Shifting from Gear...

My Peugeot 407 1,6 HDI is becoming very sluggish to drive in terms of acceleration. Lacks power on any incline, i have replaced oil filters. Previous owner said it needed the glow plugs replacing but my mechanic father (who admits his diesel knowledge isn't great) thinks that only affects the starting of the car (which is fine). Will changing glow...

Good evening,

2018 partner van 100000 miles.

Got an interesting problem, I was looking around the van after a wee drive and noticed a fairly substantial leak under the van. Got it onto the ramp and discovered that ad-blue was leaking from the connectors going to the injector on the exaust. I assumed that the valve was jammed in the injector so...

I've just acquired a tatty and unloved 208 for my son. It does start, but the idle is really lumpy and the accelerator does absolutely nothing, no response at all.

I'm also a bit suspicious that the fan continues running after switch off. I'm not quite sure why, as the engine is not hot, and the dash temp guage reads still pretty low.

I havent...

Hi I am new to this forum but am desperate for answers to the following issues, the stop lights up on the instrument panel and cuts the engine. After turning it off and waiting for the stop message to go out it will restart and run normally. It comes up with crank position sensor and camshaft position errors. It has been to main dealers and had...

Hi. Im doing an engine conversion on my talbot express motorhome.
Im using an hdi engine with bosch single plug ecu edc15c2.
I can't get crank cam synchronisation. I've continuity checked every wire. I have new sensors. There is 5v at cam sensor. Crank rpm is showing on Peugeot planet 2000.
The non synchronisation was showing as a fault but not...

Finally got the 306 Cabrio out of the garage the other day after a long Winter's hibernation, to be able to wash her, get her ready for a proper professional detailing, and get he ready for the decent weather. Thought I'd try raising and lowering the top...just so I'd know how to do it.

Well....that did't work out so well, as I attempted to get...

The offside sliding door on myPeugeot Traveller 2020 is catching on the rear wheel hub. Is there anyway I can adjust the lining of the door to stop this? Any advice gratefully received. Thank you.

Boxer 3 2.0 hdi
Been trying to detect a parasitic draw. I found what I believe it was on the 40A fuse in the engine compartment for the fuel heater. It was reading about 180mA before. Once I pulled the fuse the meter dropped by around 100mA. I was using a clamp meter so not the most accurate way.

The fuse is back in and now when taking a...

Hi everyone.

I'm going to replace my hydraulic lifters soon. Some of them are worn out and noisy but I want to replace them all (as recommended by experts) to make sure others don't fail soon.

The car is a Peugeot 406 1.8 16V with XU7JP4 LFY engine.

I have already bought a complete set of brand new hydraulic lifters.

121725387.jpg

I was...

Peugeot 207cc 1.6HDi glow plug control unit. The part with the aluminium heat sink.
Anyone know where it lives on the car?

Hello all. I wonder if anyone can think why a 2007 207 1.4 VTi would keep fouling its plugs and resulting in misfires, cylinder shut offs and no starts.

Background.
Car has only 25k miles from new. Owned for 10+years. Used weekly, doesn't go very far.

The problem started around a year ago, when the car was running rough. Probably on 3 cylinders....

Morning all,
Recently started getting this warning message when I go to start the car.
Only comes up intermittently though. Disappears as soon as the car starts.
The very odd time the car won't turn over when I press the start button until
I disconnect the battery and reconnect it.
Got a new battery in Jan from Peugeot. When I press the start...

I had a major service at 43k miles and Mot after around driving the van for around 200 miles the engine light came on saying fix needed then adblue light started flashing and emissions fault came up on screen. Vans had all dealer services.

my 1.6 bluehdi 2016 69000 miles, started giving fault code p2448 when in automatic mode getting to 2000rpm loses power and throws a code and uses lots of fuel and seems to hunt a little, so I clear code ok till I get to 2000 rpm and does the same, now when I put in manual mode on gearbox it drives fantastic no fault codes drives as smooth as silk...

Hello!
Im start losing faith in myself after trying to fight TPMS problem in my 2008gtline 1.2 at
I read simmilar topics on forum and none of them suits my problem.
However i used knowledge and help from other users to try solve problems. But saddly without results.

So... car comes with error after turning key TPMS monitoring system fault. As i...

Hi,

I've watching the forum for a while, taking as much info as I can about mirascript since there isn't much documentation on it

I finally bit the bullet and attempted to follow this tutorial.

I got a friend's unit for a day. Copied his user files. All good so far. I turned on my unit with a brand new sd card. Put in the upgrade cd and ran...

Need help where to start as it seams as multiple issues…
I can smell lot of diesel fumes in cabin and when stationary…Throttle body area is wet (oil).
I opened injectors cover and found yellow residue on the inj.pipes and all over..(sticky) more then wet…
Where do I start guys please?

The screen on our 2019 308sw worked this morning but now has decided to not start up after being parked for a shopping trip. All it is showing is the Peugeot lion logo with a dark blue back ground and touching the icons at the sides does nothing. The car has been switched off and left locked for a couple of hours but it made no difference when the...

Hello. The car is a Peugeot 508 SW 2.0 HDI 163HP from 2011. The gearbox stopped working in the car. It was repaired. The car has driven about 150 km after the repair. The problem is that the car changes gears for about 1 minute. Then the gearbox shifts from D1 to D5 and that's the end of the drive. The last time I was able to scan all the modules...

Hi

I had reason to take the locking ring off my diesel tank on the 407 estate.

When reinstalling, I noticed it had a arrow pointer but no visible marker on the tank body that I could see.

It looks about right as the ABS sensor holes are in the right spots, I can't screw it in anymore and no movement from the pump when pushed down.

Any ideas...

Hi,

After replacing the original but faulty advance solenoid (coded) with a non coded LUCAS solenoid, I can't start the car.
The new solenoid receives +12V correctly after I start the car with the key.

A diagnostic with PP2000, shows this Default :

ECU Engine / Permanent Fault. Pump Module locked.

Tried to remove F2 fuse : issue is still...

Does anybody know where I could find a fuel pump relay?

Bitron type 240.101 part number 9607540680

Thank you.