French Car Forum

While error code reading the 308 for a problem with engine I had the following code returned as well.

B1003 54 Secure configuration fault. This is the COMBINE_UDS ECU and under properties it says:
Cause - Local
Status - Present
Characteristics of the fault - Absence of calibration

It seems to be something to do with the dashboard.

Any ideas?

I have been replying to a thread about a 405 coupe. It's suddenly disappeared, why ?

Hi all, I've just joined the forum in the hope that someone may be able to help me. In October 2019 I purchased my lovely 2012 5008 1.6HDI. Despite a few minor issues it's been a great car so far, one niggly issue is my EGR valve is showing a fail on OBD reading but the car 99% of the time is perfectly fine with the occasional little bit of...

I bought a 2015 508 SW yesterday, so far did about 520 miles to get it home, really nice car. :roll:

One quirk it has is that the infotainment system puts up a message that the system temperature is too high, restricting volume. The volume is then restricted to 15.

Yesterday was a cold day so the interior heater was at HI and the message came...

Well didn't expect to be back quite so soon! Took 307 to Halfords for an MOT with it's nice new fuse box installed and it failed. Checked discs & pads, ground off lip from discs and measured the thickness, rear 7.4mm (min 7mm) and front 23mm (min 24mm). I intend to replace pads & discs but no time to get, at a reasonable price, and fit before MOT....

I have a 2007 407 2.0 HDI coupe, fault code p2033 displayed. Can you confirm part No for my EGT sensor is 1618PG/ SH/ 30. And are there any less expensive variants I can use.
Many thanks.

Hi guys,
my airbag light came on after i removed the airbag of the steering wheel and lubricated the inside of the steering wheel with WD40..
Do i need to make some process to reset the airbag light or did i damage the circular connector of the airbag with the WD40?

Ok guys I need some help, the wife's 5008 1.6 HDI 112 EGC (61 plate) is throwing up some codes today.
It's got 68k so not a high miler.
This is what my cheapo reader comes up with.

P0263 Cylinder 1 contribution / balance

P0559 Break booster pressure sensor circuit intermittent

U1108 unidentified code

U1113 unidentified code

U0103 lost...

Hi all A couple of weeks ago I was on a short journey when suddenly the dash stop warning light came on then everything on the dash flashed on and off and the speedo stopped working. I pulled up just down the road just a short distance from where I had to go. When I returned and tried to start, the battery would not turn the engine over, This a...

I have read on some forums that its possible to add cruise control option on this car,It needs just cruise control switch.This is what I have bellow steering wheel.

Evening all, I was about to do a bit of AM6 preventative maintenance and noticed a leak from the 'heat exchanger' under the drivers side. I can't find it in the BOLs or on servicebox. The water leak is from the front edge, I've not removed the cover to see where exactly. Is this a known issue and can anyone point in the right direction regarding...

Hi there ! I’m new here so expect many dumb questions:-)

Today I was playing with a cheap odb2 scanner, just to read some values and try to understand the meanings.

One thing took my curiosity : the Throttle position % was at near 15% even with the engine off and the pedal not pressed. If I press the pedal completely I read 80%

Is this normal ?...

When I bought this car it was comed with some kind after market built alarm system.Now Im interested how to completely disable this aftermarket alarm and re-enable stock key locking because now stock key lock buttons not respond at all.Tnx

Anyone can explain me (Givemeabreak for sure can :-D ) what does the abbreviations BVA,BVM and MAD found on the service manual (or Servicebox) mean ?

BVA and BVM sound to me like automatic gears and manual gears , but MAD ? (for example descriptions like Since MAD 1036789 )

thanks
Dave

Hello, i need your opinion about my timing belt status.

I've bought this used Peugeot, but the seller doesn't know if the timing belt was replaced on the last service.
So, before i start disassembly my car, i've opened the cover and tried to take some pictures of the actual timing belt, both sides.

I'm sorry for the pictures but it was not easy...

Hi,

I've used aero-style blades for cars in the past based on forum recommendations, is there a particular type or brand that's popular for 407 SWs?

Hi,

Installed anker towbar but now need to wire the electric. I have the bypass relay teb7as 7 way for standard or modulated circuits but reading up on this system I probably can't get away with being all mud neck with the install and just jacking into the lighting circuit near the bulbs.

So I need the Peugeot approved wiring as this appears to...

Im putting an XUD Turbo D engine that originally came from a Citroen ZX into a Peugeot 205.

Looking to use an oil cooler, i see some factory 205 d turbos have an upright oil cooler for improved clearance.

Servicebox is not much help in showing me this upright oil cooler, any idea if it was fitted to other cars or why its not on servicebox?

The...

The clutch has started to slip on our 2007 1.6 Hdi 110, I can't complain it has 160K on the original. I understand that it may have a Sachs or an LUK setup but is there any way to tell which I have before I take the gearbox off so that I can have the parts ready?

Thanks all...

Sorry guys, I just have so many questions!

I found a strange black device hiding away in the passenger-side visor. It seems a bit conspicuous to be anything from MI5. It comes off easily enough as it's just fixed with some sticky pads. Any thoughts?

Hi !

i've asked an official Peugeot reseller how much it will cost to replace my timing belt. Answer : 1500 chf (= 1395 eur = 1177 gbp) :shock: :shock: :shock:

It's a little more than my actual budget, so i'll try to do it myself. It's not rocket science if i follow the important security things like the locking of the crank and cam pulleys....

Me again :oops:

My central display is faulty, starting off fairly legible when firing up the car, then gradually fading out to almost nothing by the end of the journey. I understand that this is a fairly common problem. Is the best solution simply to replace the screen with a genuine OEM unit for around £150 or so?

Today when I was driving, I had my fans on to keep the windscreen clear. Then whilst I was driving, the fans got slower, and slower and then eventually went off. I turned the car off, started it back up again and they came on again but wouldn't get up to speed and slowly died again. I've heard about a heater blower resistor that could possibly...

I have just got a 207 running with a new injector but PP2000 wants an 8 digit code and the injector has 10 digits on the sticker. The original injectors have 9 and the last digit is simply dropped when programming but I don't want to guess how which 8 digits to use and cause an issue.

Any information would be great. Thanks.

Last year, my Peugeot 5008 had a new turbo and EGR valve (along with alot of other things totalling £3000!) its currently on 236,000 miles and going strong, but for about 6 months, the EGR valve has been causing problems with juddering. When you accelerate moderately or hard, there is a jerk or what feels like a misfire at about 2k rpm. You can...

Hey Peugeot people. I'm tryna figure out whether it's worth trying to fix my car or whether I should just scrap it. It's a:

Peugeot 307 SW (2004, 2.0L, Automatic)

Here's what's happened:

An engine check light had been on for a few days (which I'll never put off addressing again..)
I was driving normally on the flat and then lost acceleration...

Can anyone tell me where the power steering electronic control module is on a Peugeot 107 (06 plate) and how to remove it?

Hi all, I'm new to the forum.

I bought a 407 SW from a dealer just a couple of days ago. It drove fine on the test drive, but driving it home and then further trips have proved problematic.

The most worrisome one for me was last night. I'd driven it for 15 mins, parked up and returned after an hour or so. At first, the dash showed the skidding...

I have fault codes p0011 and p0420.
Does anyone have any idea what this is?
Please help I’m going insane

Second time it’s come up on the dashboard. First time was only last week! Car goes into limp mode when in full auto. Just about manages to hit 70 when I put it in a manual :( Taking the car to the garage in the morning. Any idea what could be the problem?

I’ve got a van with the xud engine in and it’s started to smoke, a lot! Clouds of blue smoke. And a big oil leak from the rocker cover. I guess these are related as they started around the same time. I was told that the smoke would be oil seals in the turbo so I changed that. It still smokes. Any ideas? Could it be a blocked breather?

Hi, Can anyone confirm if the 2016 1.6blue HDI , still has the filter in the turbo oil pipes. I'm sure iv seen on here that peugeot removed them at one point but can't find the post anymore. Does anyone have access to peugeot parts system putting my vin number in should show on a parts diagram if it's fitted or not?

I dont want to remove the cat...

Hi all, just been to run PP2000 on my mum's little 107. It's an '06 plate with not quite 24k under it's belt and on it's original Fiamma battery(!)

The issue she'd had with it was a couple of times recently, after starting up it would (as I was told) refuse to go into gear/act as if the brakes were applied, accompanied by a warning beep sounding....

Hello :)

I have a Peugeot Boxer(II), 3.0 HDI - F1CE0481D, 2010, vin nr VF3**************[VIN obfuscated, can be read by forum staff]. Where motorlamp fire and turbo pressure goes on and of while driving, got some fault codes (Delphi diagnose) :

035F - Unknown fault code

2085 - Unknown fault code

P0481 - Engine fan 2, too high tempretur, periodic

P2453 - Differential pressure DPF,...

Hi everyone, new here and wonder if someone could give me some advice regarding removing lock cylinders on the doors of my Pug Expert(2003)

I have just ordered a set of locks off ebay. Pattern parts but they will have to do. How easy is it to remove the cylinders? How do I go about it?

Any help very much appreciated.

Hi
Our 2008 107 has developed a fault whereby the horn sounds when the steering is turned to full lock in either direction. No obvious sign of damage etc behind the airbag etc so I have replaced the clock spring with one from a breakers and it still does it !
Apart from the replacement clock spring also being faulty is there anything else it could...

Hi

I have a Peugeot 207 2011 diesel. Backstory - in June I had the MOt and my nearside spring had broken and the shock absorber was shot so they were replaced and the garage carried out wheel alignment. Unfortunately the steering wheel was angled about 60 degrees to the right when the car was going straight! I took it back next day and they...

Could anyone help?

Just bought a 405 which doesn't seem to need a code entering on the keypad to start it, although the keypad has the red light on it with ignition off, and 'peeps' three times when you turn the engine off.

I've heard you can disable the keypads and it looks like this one has been, but could this cause problems later on if, say,...

Is there anyone that has swapped a Puretech 130 engine and manual gearbox from (say) a 308 or 3008 into a 205?
I like triples and all of that low and mid-range torque is more useful in a fast road car than top end.

The 1600 is getting tired and the Puretechs would be nice and light too.
Or is there a major hurdle in such a swap?

Cheers, Chris.

Hi all,

Iv got a 2016 308 T9 with the 1.6blue HDI Engine iv had it around 6 months now and it's been fine. When I bought the car it had U3FFF a temporary low fuel pressure fault code logged which cleared and didn't come back. However now every so often when I start it up from cold the engine hunts a little and the service light occasionally comes...

Hello, at first i would like to sorry for my English, but it's not my national language. I decided to describe my problem at foreign forum because my local ones has out of ideas for my issue. In short; i was in two different roling roads and my THP175 has ~140hp and i have two rpm drops, always at specific range. First between 3000-4000 and second...

Hello I've got a driver seat belt which has started going on the edges warn frail bits.

Its for the driver side front. I was looking for second hand one. I've seen some and thought do the other sides fit as the driver side gets used more so thought if there the same I'd get passenger one.

Peugeot 306 hdi 2000 ph3

Thanks

Hello everyone.
I am looking to test my car (which is equipped with this engine) to see how fast and healthy it is. I have a criteria for measuring engine power which is far better and more reliable than 0-100 km/h acceleration times. Any performance measurement that requires launching from start is useless for me because it depends on factors...

Hello I want to know how to see condictions of injectors in diagbox 7.83.How to test and see are they good?Tnx in advance.

My 2015 308sw has developed a problem: the eco-mode comes on when stationery but the engine does not restart when I press the clutch in - I have to press the eco-mode button to restart. No problems with changing gear.
Has anyone else had this problem or know what it may be?
Thanks.

Hi all,

I have a Peugeot 207 gt for two years now. after 2 piston break I decided to forged my engine and some other upgrade like intercooler and a turbo k04 and the ECU was remapped by Stelios from etuners. my problem is that I am not having the expected power out of it and my mechanical man does not know where the problem is coming. can anyone...

Hi,

What are the differences in engine equipment in 150 and 175? In short, what parts gives additionally +25hp from 150hp engine?

Hi

i have a 2012 1.6 diesel Peugeot partner that has developed a bad fumes smell in cab with or with out heaters on . i checked injectors and one was sooted/black around base of injector so i removed and replaced the copper washer.
however this fumes like smell is still present in the cab with or with out heaters on . its not a very nice smell...

A random question, i have a peugeot 5008, DW10CTED4 2.0 2010. On the partslink diagrams, after the turbo on the exhaust side, it shows a catalytic converter before it carrys on to the DPF. Can a DPF car have a catalytic converter too? My car is on 238,000 miles and im wondering if its likely to be blocked given the mileage?

Hi,

someone please tell me what the two sensors in front of the diesel fuel filter housing are for, one seems blue and the other brown. Im redoing my loom and i cant find connectors that go onto them so i think its better i know what they are.

Regards.