French Car Forum

I tried to program a new keyless fob on my Peugeot 308 T8 with Diagbox.

I followed the procedure which suggested I start programming the old working key first, and then the new key.

Unfortunately, the programming of the old key appear to have failed with Diagbox giving the following error: Incorrect hands free remote control number or hands free...

Hi all,
New member,first off read upto 30plus page & I must say the knowledge & tips on here is terrific,so many thanks guys.

Couldn't start new thread as being new..
Peugeot partner 16hdi 2010
have had the van for 6mths,when I bought it they said slight oil leak,which I did check & there's been no problems,
But with reading on forums like this...

Hi all!

Got an issue with the auto box on a 2.1td 605 ive just bought -

it seems very reluctant to change up a gear, it will hang onto 2nd gear until well over 30mph for example.

I was told by the previous owner that a gearbx oil change is due and he did supply the correct grade of atf for the job. There is also an oil leak coming from the...

Hello all, I got an error message on the display that particle filter additive level too low. I've been in service few months ago and they had to refill additive. Today i've been on dignostic with my car and it shows, that car has 97% of additivum. We restared the control unit but the error has showed again. So what's wrong? Car goes normally....

Hi, engine is a 2.0l HDi, DW10 BTED4 / RHR model. 140k.
The engine has a whine coming from the crankshaft pulley area, you can hear it in this vid (engine is at idle):

I've only recently purchased the vehicle and it is possible the whine was there when I got it but with the wheel liner and undertray in place I didn't notice it. Last week I...

I have a mysterious drivetrain rumble, and am wondering how I work out which bit it is.

1997 Expert TD van, 158000 miles, so getting a bit tired. Have owned since 2000 and not had any drivetrain trouble - just had to replace the gaiters in last few years. Or put another way everything is old. Oh yes, and it's the original NA gearbox with a 1994...

Hi Guys thanks for letting me join the forum i stumbled across this when trying to get some information on my 3008

I have a 2011 3008 1.6 hdi which recently has been causing me problems going into limp mode i do have an ebay scan tool box its the WOW version i think its the same a the delphi one anyway i plugged it in and it come up with injector...

Hi,

does anyone have a pin out list for the large plug that goes through bulk head on a 206 hdi 2.0. i have worked out the smaller plug this is mainly for dash signals. i currently have loom out of car and in the middle converting for a none psa fuse box.

Thanks, Nick

Hi all,

where best to buy uprated nozzles for a 206 hdi 2.0 injector? what sizes are available for these?

thanks, Nick

Hi really hoping somebody can help

I have a 1997 106 gti the battery light sometimes comes on faint random on and off, it’s charging fine nearly 14v

Alternator is new genuine nos
New varta battery
Cleaned connections battery starter and alternator And earth to gear box

Took it for quick spin earlier and noticed that when the light comes,...

Hi guys (and womens) 🙂. (sorry for my spelling, im from SWEDEN)

I try to help my friend with his peugeot 306 2.0 16v 1997 convertible.
He got it from his past away uncle, it has been standing still for 2 years.

Battery was dead, bought a new one and put it in.
Engine cranks but dont start.

I have found a problem with the double relay.
The...

My van (1.9D) didn't come with a front anti-roll bar. But does have the mounts for the bushes. I notice that the 806 TD I got a lot of bits from many years ago did have one. I should have taken it then, but it was a long day and I skipped it.

So, as I have both front suspension side off at the moment, now would be a good time to put in an...

Hi, hope someone can figure this one out for me...

I have a 2004, 2.0Hdi Partner, last year around this time the crankshaft pulley begen to get noisy, squeaking if I remember. I changed it and changed the belt too. Fixed the noise. Then about a month later another different noise appeared, more of an agrivated hiss sound. As I'd just got another...

Hi, I have a Peugeot 207 2010.with the piloted manual gearbox(sensodrive) .i recently changed the clutch kit because is was completely worn. Now I have a error code p1795 and I can’t seem to get what the problem is. Kindly help.

Hello,

My rain sensor is not working properly since I bought the car. I noticed that windshield is changed, but sensor is still there. Wiping is done very late, when you can't see anything from the rain.

I purchased token on servicebox and scanned the car. The following error is here:

B1174 95 - Installation incorrect

To me, physically...

i have a 2013 peugeot partner on which i have just had an injector replaced,trouble is since the replacement, the engine will not run.rail pressure according to the (snap on) scanner is 0 bar.the only fault code is p1199 fuel circuit incoherence on the reserve fuel pressure(nearing no fuel) .there is plenty of fuel in the van and the filter has...

I brought a 307cc back in November which I knew needed some work. I parked it in my drive and finally got time to work on it yesterday but the battery is dead so I can't get into it! Remote doesn't work so I unlocked the door manually but can't open it. Problem is on this model, once the door is unlocked, the window drops about 5mm when the door...

Peugeot Boxer, 2.0 HDi DW10TD. Production year 2005. Vin VF3**************[VIN obfuscated, can be read by forum staff]
Hi, any help, advice would be very much appreciated. Since last week my van developed some strange noise. I dont have any problems with starting it or any power loss, goes well as always. Doesnt matter if the engine is cold or warm, if i press or depress clutch. Noise goes...

Hi!
I have fuel problems
system gives high fuel pressure code
And hoses for return system at injektors leaks have reaplace them and still leaks
Anyone know how to fix this problem?
Need help
Sorry for my bad English.

2litre hdi will only start when cold or fully warmed up. Any ideas? Thanks in advance.

Good afternoon, I just left of work in my Peugeot 207 that has recently had a gearbox oil change, I noticed for the first time today that the gears went from first to forth in a matter of seconds it didn't do this before also when going uphill it went into forth then dropped into third then back into forth only to repeat this again,is this a...

Hi FCF members,

I have a 55 plate 206 1.4 hdi which has had recurring issues relating to loss of power past 3k rpm and very little power going up hill.

It had p0401 and p1351 codes, I have now changed the egr valve (improved engine heat up time, idle sounds much better) but the lack of power is still there.

After I changed the EGR I took the...

Hi Guys

I am currently looking at a 4007 from an independent dealer, the problem I have is that the service book has gone missing. The previous owner has stated that it was serviced at least a couple of times at Arbury Peugeot of Lichfield. I have contacted them and they have replied that they cannot do anything until after lockdown (whenever...

Hi there!!

A few days ago I replaced the electric handbrake system on my peugeot 508.
The new one does not have the same part number as the original (9874350580), so what is happening is that the system works without any problem, automatically and manually, but the handbrake light does not turn off when I unbrake the car, it always remains on....

Does anyone know how to remove the starter motor on peugeot partner , year is 2008.
I cant access the bolts to remove it, anyone have any advise please

Hello all, this my first post.

My partner is on her 2nd phase/shape 1, 2.0 Hdi 3008. Overall, a tad weird with styling but very useful car (especially with kids). Apart from a DRC system (i.e. I binned it), its been as good as gold.

For as long as I can remember, it's made a strange noise when the igniton is turned off.
The noise is repeatable...

Hi
I have removed a faulty fuel injector from my 2014 3008 1.6HDi and now have to replace it with a new one. I have an online manual but unfortunately I cannot find the torque setting for the injector clamp. The injector is a Continental and I found the following post on this site relative to another Peugeot which says it should be 7Nm plus 90...

I'm new on this forum, but i'm sure not new to the brand, right now i'm trying to fix the A/C on my 607 2,7HDI 2005, i'll attach a picture from the code that i got from PP2000. Don't mine the first code about the auto high headlights i figured out it's the front height sensor, any prior experience or help with knowledge or diagrams is much...

HELP needed! I am learning more and more about my Peugeot 1.9TD XUD motor in my Fiat based campervan.

This morning I unintentionally spilled/drained about 1-2 liters of cooling liquid because I unscrewed a metal coverplate at the lower right side (standing in front) of my motor. Cooling liquid poored out and I spilled about 1-2 liters before...

Hi guys. My 306 Peugeot final phase won't start off in first gear and won't reach 4th gear ...
Snow and sport blink intermittently. Car is only driveable in snow mode.
The car only has one fault ...
remote intermittent fault . injection throttle potentiometer (CAN) no signal

I Checked wiring loom between the pointiometer to the transmission ECU...

Hi guys,

can anyone help me finding where it's located the oil pump relief valve ?

I would like to check if he's stuck open, but i'm not sure where to find it, and if it's a good idea to open it.

Thanks !

I have noticed an exhaust smell from the side of my car and also when a regen is taking place, smoke comes out from under the drivers side and up behind the bonnet. I had a look under the car today and noticed some sooting near the DPF Pipes. At the same time, im having some performance issues with my car. When its under load, the egr valve makes...

Hello all. I am considering buying a 2012 3008 1.6 hdi. Its done 60k and is due a timing belt change. Can anyone give me a rough idea of what would be a fair price for the job please? All advice much appreciated. Thanks.

Hi,

Just as an introduction, I am Dutch, normally driving on the right hand side, except when visiting the UK with my French camping car on a Fiat Ducato chassis having a Peugeot 1.9TD XUD9 engine (2001) and a Bosch injection pump. This latter information I have figured out until now by reading through this forum.
I read a lot and i'm puzzled a...

Expert 2011 2.0 HDI 120hp

Bought at 178.000 miles

Things been changed at 180,000 miles

Water pump
Klutch
Flywheel
Timing belt
New oil
New radiator
New cooling liquid
New gearbox oil
Head gasket + heavy cleaning (oil from the cover)
New A/C radiator
Thermostat

Plus mechaninc takes money for checking every single bolt and others things...(he...

Swmbo has this Bipper with an ECG gearbox,

Recently, sometimes when she goes over speed bumps, or turns sharp left, the Bermuda Triangle lights up followed by the klaxon of doom, the gearbox selects any gear it wants and the whole thing grinds to a halt. Garages are flummoxed, which is not in itself unusual, but does leave us adrift.
As she is a...

Hi folks, this is my first post. I have done some searching on this forum and googled, but still a little stuck.

I wanted to add the trip computer to my 2008 Expert, it looks easy enough to do and I reckoned that swapping the Comm2000 with one with the button on the stalk was the easiest way for me given that my radio stalk has buttons missing...

kw55apu
handbrake started to fail rapidly so i used the button to adjust under the handbrake. then a while later it stopped working all to gether but it only pulls up one click.

i just used the wind back tool on the rear and put new pads in her.

now i tested and there is no movement at the rear calipers and hand brake is still the same.

any...

Good evening folks
I have got a very strange problem with my 2.0 litres HDI engine (year 2004)
It goes in to limp mode when im running for aprox 3 km. and lost the power and will not rew more than 2700 rpm.
enginelight comes on and the error code supplied is P1351 (Pre/Post heating relay circuit - Relay & Pre-Heat plugs not controlled) that...

In the process of converting an 86 305 to TD power.

The engine going in is from a 405 TD that had air con and as such the arrangement for the auxillary drives is wrong for the 305 application it takes too much room.

Im looking to convert it to what a 306 or ZX without AC would have used. Would anyone have one of those for parts?
Screenshot...

Hello guys, as the subject, i have this question :

after succesfully replacing the timing belt ( i admit, with a lot of troubles ) the engine was working fine for one day, then the miserable P0011 and P0012 error appeared on my diagnosis tool and the scary low oil pressure warning on the car too.
First of all, there isn't any low oil pressure...

Hi.
After solving the problem described in this thread:

I have another problem.
Originally my 407 with RD4 does not show on the display what the parking sensors mark. I will enable it for DiagBox.

Previously, both sound and screen showed distances well.
Now sound works fine. The 4 sensors work and detect the distance well.
On the screen it only...

Hello which tool I need to unscrew this bolt whatever its called..which holds injector on 307 1.6 hdi ?Tnx in advance

Hello dear members.
I think my car (Peugeot 406 1.8 16V) has some slight (or maybe very slight) ticking noise. Since the noise comes from top of the engine, it is certainly hydraulic lifter noise (I am familiar with Fuel Injector noise and I know this is not the sound of them). This noise can only be heard with the bonnet up and the engine idling....

Evening all

Hope you're all well.

As per the title, any idea on this?

307SW 1.6 Petrol
ME745 ECU

I renewed the heater hoses on my daughter's car a few days ago and when I was bleeding the system, like a numpty, I managed to drop the thermostat bleed screw :oops:. Cue a stream of coolant spewing out before I could refit the screw, and the engine died.

After mopping up, it wouldn't restart and sounded like it was...

Hello,Im interested is it possible to enable currently cruiese speed info on multifunction type c display?It is similar like this one?Tnx

Hello Looking for a how to, or some form of guide on replacing clutch for a partner 1.6 2010 van. This clutch was replaced 3 years / 50k ago by a garage but started to slip so looks like a new one required.

I have found this link on youtube I'm hoping its similar?

Done a few clutches and engine replacements in my time, how long does this...

Hello everyone.

Yesterday I took the workshop to repair a leak of automatic gearbox oil.
When the car is returned to me, all washed, I see that the rear parking sensors do not work.

Display error: Parking assistence system faulty.

I talk to the people in the workshop and they tell me to take it today to see it.
Before taking it, I diagnose it...

Has anyone done one of these. I think I may be trying to over complicating things, plus pictorial instructions do my head in. The kit is a Erich Jaeger 736941. I've got the separate plugs in the LHS cubby hole and it's seems too straight forward to be true. If I've got it correct I need to cut the large Black/Red connector off, splice a spade...