French Car Forum

Hello guys!

I have a 407 coupe 2.7 Hdi ,it's leaking coolant and it comes from the middle of the V6 because there's lot of standing water there. I already changed the water outlet house/thermostat house it didn't help. So my guess is the oil cooler that leaks at the gasket i took out 6 from the 8 bolts but to remove the last two bolts i have to...

Not sure if any on has heard of these before but they are a decent bunch and I found them whilst searching for the auxiliary drive belt tensioner bolt online.

Worth checking with them if you have a hard-to-find part also.

Not sure if this breaches any advertising or commercial forum rules. Admin. Please remove if not allowed.

Morning all
To put it short I've need to get my work equipment out of the van,yesterday the doors were ok,in the morning afternoon they wont open,tried switching off/on the fob,tried using the key, all 3other doors working perfectly.
As previously any info greatly appreciated
Pug 16hdi 2010
Ste

Hi, we had a new windscreen fitted on the 306. the wipers now only work on one setting, we no longer have the intermitant or fast setting. will changing the wiper stalk/ lever resolve this? or do we need to replace the winscreen again! cheers Terry. :oops:

Hi guys, new here and I appreciate any comments regarding this one.

Bought a 16 plate 308 T9 2L BlueHDI, accident damaged but only minor, missing a bumper and needed the radpack replacing. Also had damage to the oil solenoid which I had to replace.

I'm getting the code P1199(I know the description of the error but there's no engine light on,...

Hello all

A friend of mine has a 205 Mardi Gras 1.6 auto. The coolant level sensor has stopped working as the low level light is permanently on now. Does anyone know how this can be fixed, are these sensor available or repairable?

thanks

James

Hi all, thanks for the ad, I am hoping you guys can help, with only a basic code reader and voltage test meter available to me at the moment its driving me mad !!

So my 2005 407 sw was running just fine and then the master cylinder on the clutch let go and pedal went to the floor.

So ordered a new unit and fitted it ( pain in ass !) bled it and...

Hello
I would ask for advice because no pseudo mechanic knows what the problem could be. I have a car with 1.6 vti 115 km engine with 42 thousand km mileage. For some time now, I started to have some problem. Namely, right after starting when the engine is on suction and has 1100 rpm, when trying to start the car starts jerking, losing power (as...

Please help...

Pug 306 2l hdi phase 3? Estate

Please would someone have a wiring diagram for the brake light switch for this car please.

The wires going to the brake light switch are 2 pairs of 2 wires.

Where do these wires come from/go to please.

The brake lights do not work and have been traced back from the lights to the loom just before...

Peugeot 2008 120 blue hdi 2015

hi,i have the emission control fault 'starting prevented in 700 miles' (not low adblu) ,do i need someone with peugeot planet to fix this? Can anyone recommend somebody in northants/beds/buck/cambs area,i live near Wellingborough,many thanks Chas.

Hi guys,

Does anyone know what the part number for the Peugeot badge is for a 207?

Thanks

Hi all, happy Friday!

I have a 207 GT and had the code p1339 come up. Changed all spark plugs and coils and cleared the EML. It's stayed off but when accelerating and high revs the car is spluttering. As if the turbo is coming in and out. I do have a cone filter and sometimes it hisses before I let my foot of the acceleration.

There is a rattle...

Hi

Can someone tell me on the pic attached (not my pic, just using for reference). where the starter motor should be located please.

My problem, car was sat for a couple of weeks, in freezing, snowy and icy conditions. tried to start car and was very low power and cranking really slow, basically drained battery.

Took battery of, charged it, put...

Could one or more of you lovely folk please tell me if the pinch bolt on a 206 strut is meant to come out, or we are just supposed to lever the clamp open a little..

Brother has his in bits at the moment to replace struts and that bolt - pictured, is stuck fast. Do we get the BFO hammer out, or do we lever the clamp apart a bit?

Thanks!

Hi.

I have peugeot boxer 2.2 hdi 2007.
And I have starting problems with it.
Problem is if I turn key to contact possitioto and wait till the orange light for plugs go of it wont start. When this happens I have to turn key to off and I have to wait till I hear click sound from plug relay or it wont start.
But if I turn the key imidlety to...

Hi all.

I have a 2000(X) Citroen Berlingo based Romahome Duo micro camper. Now bear with me cos I don't think I'm posting in the wrong area cos.................

at some point in the past, a previous owner has fitted 14 Peugeot alloy wheels to it, at least I presume they're Peugeot due to the lion centre caps.
I've had it for about 5 years now...

Hi again. After waxing lyrical about the battery management meter I fitted to check our onboard 12v condition and how we have not had any problems lately, I haven't been driving the car much at all but my wife has. All of her journeys have been very short, local ones going from shop to shop (christmas shopping!!!!!) and this fault came up and...

The ABS warning light suddenly came on. Appears again when engine re started. It came on while driving, not braking at the time. I'm going to check the break light switch and wiring inside rear light housings as some time ago we had a problem with a rear light not working, an auto electrician sorted it. I seem to remember an earthing fault was the...

Good afternoon, could someone supply the parts numbers for the rear wheel brake cylinder please for this van VF7**************[VIN obfuscated, can be read by forum staff] . I'm also going to change the shoes as they are covered in brake fluid. Last time I looked there were 2 options. Get the complete kit (cylinder, shoes and springs) or get the cylinder and shoes without the springs.
Also...

My fathers peugeot 305 1.9D is smoking white under acceleration and when i rev the engine. Engine has been refurbished once about 10 years ago. Any ideas? When under load its smoking more white. Ita not coolant, coolant is at the right level.can it be water in the diesel fuel filter maybe? Or this is definitely oil burning ?

Might someone know of a good Peugeot parts supplier mail order or online please ?

Hi guys im new here and as usual a newbie finds and joins the forum because he is in need of some help.

I called into Peugeot today to try and find out which gearbox i need for my Expert. The guy there told me to look for the sticker on the box itself.

I have looked and its gone haha

I need to get a replacement box and have found that it is a...

weve had several peugeot 207cc convertibles over the years , all been great motors..
however the latest one 2012 white garros only 39k is causing big issues.. just had a split hydraulic hose in the boot for the roof.. and now the dreaded esp/abs problem..

So ive removed the pump and have sent it to control codes, whom confirmed the pump is...

Hi is there any one in the Kent area who has planet?
I've fitted the cruise control stalk but need it coding in correctly.
Did have a bloke try but don't think he did it correctly

What is needed to replace the 2006 Peugeot 4 speed AT (ZF 4HP20 ) with a 6 speed AT (AM6).

Hi can someone help me to find
peugeot 308 2011 bsi johnson control and gps display wiring diagram
peugeot 208 2016 bsi valeo wiring diagram
peugeot partner 2016 bsi delphi withe screen wiring diagram
need almost to find can h can l confort pinout to power up on table navigation system
Thanks a lot

Hi all,
I'm new here, looking for some wise advice.
My wife's got a 2011 Peugeot 308CC. Recently it's taken to saying tyre pressures not monitored on random occasions. It might go a week or 10 days without trouble.

So my question is - what to do? Is it likely to be one of the tyre sensors? Or the TPMS ecu?

I could buy a used TPMS ecu on the...

64 plate Peugeot Expert with a 2.0 HDi DPF aka the big brown bus the coolant is also a fetching brown colour !

nearly 7 yr old but only 62k

Using the reg no. Comma say this is the right coolant

Ethylene glycol based antifreeze & coolant with OAT

what would be the equivalent stuff from Euro Car Parts I can see all the colours of the rainbow...

hi i have a peugoet 207 gt 1.6 hdi. 2008
it has a severe starting problem.
it will refuse to start from cold and it will start from warm when it feels like it
it will start straight away with easy start.
when it does not start its like its just cranking over not even trying to start like its out of fuel. then say on the third try of cranking i...

Hi, what are the torque settings on my wifes 306 , 1.4 petrol, rocker cover ? I am about to change the gasket. cheers Terry.

on a 1.6 HDi how is the heat shield attached that sits between the DPF housing and the engine block?

mine has no outer/front shields/around turbo just the rear one between dpf/cat and engine block, when I recently changed my turbo I didnt drop the DPF unit out of the car but I couldnt get the shield far enough away to get at the Banjo Bolt for...

Hi. I have been a follower of this forum for a while now and I have taken the plunge and joined up. My car, a Peugeot 3008 Hybrid4 2013, has had a problem with the service (12v) battery running down. It started 3 months ago and the faults that occurred were Air bag/pretensioner dash light came on followed by the amber engine repair required dash...

Hello,

What can be the problem of this DTC, it says that correction of quantity of the injected fuel was insufficient.

What I experienced that sometimes at start car coughs and then engine turns on and work properly.
Also around 2000rpm I experience slight twitch of the engine.

Still I fear to start repair from injectors and buy a new ones or...

Hi guys, does anyone know the part number or name of number 5 in this picture, mines is damaged, looks like someone has perviously had an issues with fitting it properly and the end is split.
Would like to see if I can buy one from somewhere but don’t know what it’s actually called.
Thanks
Stuart

A question (or two) for those in the know; I'm looking to do a full service on the 2.0 Peugeot Expert Tepee I recently purchased. For all filters I'm going with MANN products as I've used them for years and trust the brand but the engine oil is the one in question. I see some recommending TOTAL QUARTZ and I've found 5ltrs of TOTAL QUARTZ INEO ECS...

my car 3008 - 2016
for some reason i take off a start engine fuse when i close it
at morning when i reconnect that fuse and connect battery , it working but shows more error in screen at once
engine fault \ gearbox fault\ esp/asr fault \ power steering fault

i take all souluttions.. cheks fuses - replace battery - but still error - can move but...

so my new to me 207 HDi came with a full DPF, along with many things wrong that will have definatley led to it getting full:

clogged air filter
non working MAF
split boost pipe
EGR stuck open
lack of general servicing

I have fixed all of those faults , and its been on a couple of trips where it ran well and hit good mpg, no fault codes were...

Hi
I am new to this group
please bear with me if i get it wrong
im touching 60 and not great with this sort of thing

I have a 2017 2008 1.6hdi 100 dv6fd engine
runs perfect , however i have a water leak
I looked underneath and i can see a small clearish pipe sticking out the bottom back of the engine
it goes through a guide hole more to front...

Hi All,

I have some electrical issues on my Diesel 5008 (2013) DV6 and and considering replacimg the complete engine wiring harness.

I have a used one in very good condition that I plan to try.

Obviously this will be easier with the wiper scuttle/tray removed... Is there anything I should be particularly aware or a procedure to follow to make...

Hi,
While changing brake pads on front n/s this morning I looked and thought something is different on this side compared the the o/s, I stuck my head back under at o/s and took this photo.

244426407_221984496583646_2813029711773307223_n.jpg

o/s has this fixed bar from body to chassis but passenger side doesn't, fixing points are on n/s but it...

Hi, changed diesel fiter , started well, a little air in system, tried to prime via tech book info , screw on pump , could not find this, so tried via union pipe, and injectors, as surggested, by tech book ,suddenly stopped , will not start now, any ideals pls

Hi i hope someone can help please. I have had the car nearly 3 years love it. 2015 plate with 45,000 on clock. Drives great went in for service at peugeot in March. Since then its drank oil. 1 litre per 1000 miles. 5000 miles on 5 litres later. I have been back to them, and they are unsure of the issue, theres no signs of oil leaks and no smoke....

Hi all.

I have questions...

Is the voltage regulator that is bolted to the alternator (valeo) on a 2010 Pug 5008 unique or coded to that ECU?

Is it worth replacing the voltage regulator of alternator codes are still present after changing the alternator?

Finally, in the event that I were to buy a used ECU, what is the score with fitting,...

Hello everyone. I'm at the end of my tether and wonder if anyone could advise me please.

I have a Peugeot 3008 (2010) automatic fitted with the 2.0 163hp HDI engine (DW10CTED4). It seems to have developed a problem with the Throttle Body. I have tried to order a replacement (Valeo) but the unit supplied is totally different compared to the one...

I'm about to repair the junctions of the upper inlet manifold part of my XUD11BTE (2.1TD) , I bought 4 original rubber seals, because the ones installed are badly leaking oil. I found them on Ebay quite cheap, btw.:

The procedure of changing them seems pretty easy, but I've got a couple of questions before doing it:

- what's the best way to...

Hi I have problem locating the other end of hose (vacuum ?) on my attached photo.
Can anyone help, please?
Thank you.

the joint between either my turbo and manifold, or manifold to head is blowing on my 207 hdi

looks fairly easy to get the turbo off, helped on this car I am sure as there are no heat shields fitted

I have both gaskets already

easy job or not?

Hi all,I have just joined this forum,I was Hoping some of your members may point me in the right direction.my car is a peugeot 307,2003 model with the 8 valve 1.4 petrol engine,the problem is I am experiencing a hesitancy/flat spot. when accelerating, I have changed plugs and air filter,there are no stored codes after scanning,I have previously...

Hi there,

I have recently bought a Pug 207. I love it. It’s basically the standard model (with plastic wheels, I know!!)

However, I am looking to put some alloys on the car. I am wondering if the Peugeot 206 alloy wheels will fit my car? I’ve scoured the internet and can’t find anything!!

Any help would be appreciated, thanks!

Hi all

My 2007 Partner van (1.6 hdi) decided to not crank over, It has been fine, I parked up got out and returned ten minutes later to no cranking. I can't even hear the solenoid clicking.

Assuming the battery was dead, I checked with my volt meter but I was getting 12.65ish, pretty good. Anyways I asked a friend for a boost, but nope still...