French Car Forum

Hi. Looking for a bit of advice... Have set about replacing the front coil springs on my 2006 Peugeot Partner MPV - when I check out replacement springs online (using the vehicle reg) I am generally getting two options - for vehicles with/without A/C... my vehicle has A/C but the existing springs are different to the image for the A/C version and...

Hello

I got two message in the display saying:
Engine fault: Repair needed
and
Particle filter additive level too low: Repair needed

Came up directly after i filled up full tank of diesel at the gasstation.

The car is a 3008 1.6 hdi with 163474 km and manufactured november 2013.
And the VIN VF3**************[VIN obfuscated, can be read by forum staff]

Diagbox says HDI_SID807_BR2
P15B3...

Hi,

I am having trouble identifying the name/number of the body part that is the windshield gasket. I can't find such a gasket anywhere.
Can anyone tell me the part number or where to buy such a thing online?

Car model: 407 SW, 2.0 HDI from 2006.

Hi guys,
Bought a can of CRC gdi inlet valve cleaner to remove some of the carbon crud on my 308 cabriolet 1.6 thp engine.
Any ideas as to where the MAF sensor is located and where's the best place to spray the cleaner forward of this? Cleaned everywhere else and only other thing that's making the car hesitate is the carbon build up....I think....

Anyone removed driveshafts from a 308 is it easy because I need them out before I take engine out cheers

I have a 2008 Peugeot 308 1.6 diesel with around 120k on.. It's a decent car for what I need but it has had an ongoing issue. When warm, and more often when the aircon is switched on, it randomly stalls and may or may not restart immediately. If it doesn't restart it sounds like a giant sewing machine when it turns over (last time I had a car...

Hi.

2012 508SW GT 2.2 diesel
I have refilled my dpf tank and am trying to reset the counter with diagbox. It reads all the faults but after initiating the reset it just comes back with a unsuccessful and communication error . I took it to a independent garage and they encountered the same problem. Not too sure what diagnostic equipment they were...

Hi,

I found this forum after replacing the NOX sensor on our 2016 208 1.6HDi (100ps).

I've read so much about people taking their car to the dealer/specialist only to find that after many £££££ss it appears that the techys didn't really know what the problem was, just replacing stuff at customer's cost until the problem went away.

Background -...

This morning, just set off and the car started jerking. I thought it may be the gearbox missing a shift. It can sometimes be a little harsh between 2nd and 3rd but only when the engine is warmed up. Another 1/2 mile and it cut out. Restarted straight away then cut out again. Wouldn't restart. 3 minutes later, restarted and drove normally. Got it...

Has anyone used the contact buttons to report breakdowns or ask Peugeot for assistance? Would love to hear of your experience. Thanks in advance.

Hello all, Im having difficulty with my Expert van. Its a 2015 2.0hdi 163/rhh automatic. It went from working perfectly, parked it up and now it wont start. It just cranks over and over. Hooked it up to diagbox and I get 2 re occuring fault codes. P0342 loss of camshaft whilst engine running. And p2134 tight spot switch for acc pedal, the voltage...

Pug 206

VF3**************[VIN obfuscated, can be read by forum staff]

bought 2 from ebay, neither fit? can anyone help with the right part number please

Does anybody know how to judge the pressure differences across a Diesel Particulate Filter? I appreciate the cars computers will try to initiate regenerations to keep the DPF working as best as it can, but I was wondering if anybody had any sort of chart that would indicate limits or zones so I could plot the differential pressures I get during...

Hi guys!

I ned Your help, I am not sure 100% what could resolve my problem.

Firstly the parameters of my car:

Peugeot 407 sedan
2.0i RFJ (EW10A)
2006

About the issue:
The cooling fan does not kick in at low speed at all. The high speed operates as expected.
I checked the car with diagbox, no fault codes.
I tried to test if I can turn on the...

Hello, I own a Bipper 2008 1.4 Diesel.

After switching off engine and remove the key the dash stays on as if on ignition position. Plus gives airbag fault (almost every time) and fuel cutoff unavailable and temperature or fuel gauge stays in reading position and does not go to zero. Key locking does not work but if the van is locked via the door...

Just a little note for anyone who has found they cannot open their 407 SW glass hatch by pressing the button under the rear wiper pivot.

I know the glass hatch is probably not especially useful to many folk but, if you find that pressing the button under the rear wiper pivot doesn't release it you may have the problem I did and you may be able to...

Peugeot 308(t9) 1.6bluehdi P00BC error
Replaced Maf and Map sensors and still the same. Error pop up when driving and releasing accelerator pedal while its in gear. İt mean when engine in compressor (I dont know is it correctly in English words) Turbo hoses looks good not any leak, also intercooler doesnt leak. Does anyone have any ideas of what...

Just a little note on how I remove tight plastic oil filter caps without messing them up. Might be teaching nan to suck eggs to many but I thought I'd share the idea with some photos...

1. Clean around cap
2. Fit a jubilee clip around the 3-inch diameter cap resting it on the flange where the cap meets the alloy oil filter tub
3. Snug it up just...

Hi folks, been lurking on and off but this is my first post.
early reg 2000 (probably made 1999) Boxer 230 1.9TD, motorhome. Had airlock issues and narrowed it down to the pump. Will run all day, but once stopped for 1 hour or more it will fail to start without bleeding the air.

1. Anyway, looking for 2nd hand pump, I see a 406 pump still on the...

2004, Pug partner 2.0 hdi.

Rear brakes needed new shoes and a piston changed. Shoes were the 'easy' bit. the piston is proving a nightmare job. First the union on the back od the piston was so corroded it wouldn't turn at all with a brake spanner. Had to use molegrips on the nut, the result of this was the copper brake pipe twisted and the union...

Hi,

This is my 1st post here. Sorry for my bad English. :)

I have issue with my Peugeot 206 1.4 (2002). From time to time my speedometer dies while driving. First I hear two beeps, airbag icon flashes and all meter dies except for gasoline. If I turn engline off while the speedometer is not working then I can't turn it on again - I hear starter...

Hi, im attaching the photo of the my Peugeot Partner Tepee Actuator Hydraulic tank. My question is the level. Should i top up it or it’s the normal level ?

Thank you,

Hi

I currenty drive a 2009 207 SW. Need to upgrade to a ULEZ eURO 6 diesel and was thinking about a 2015/2016 308 1.6 SW.

I just wondered what the common issues with 2015 308's and what I should as the seller/dealer.

Thanks

Calum

ps the car i'm looking at online has done 104,000 and has just past its MOT with the advisors
'Monitor and repair...

I had the tracking done on my car last year and since then the steering wheel was off centre to the right and while accelerating the car would either pull to the right or the steering wheel would turn itself to the left to keep the car straight. As soon as I let off the accelerator, the wheel would return back to its middle position. The more...

hi to all
hear is an update on my previous topic had diagnostics done on the car today and they told me that there was a fault with communicateing with the dpf fuel tank on the can bus diagnostic circuit has anyone had this fault and does anyone have a wiring diagrame for the dpf tank
david

Hi,

I have a 407 2.0Hdi with the fault codes P1471 and P1351. The P1351 is related to the Glow Plugs and a comment fault, so that’s fine. Got a lot of help from a member here (Marc). Relating to the P1471 I have changed the air doser, the doser’s electrovalve. Is there something else to check, replace or code with Diagbox? When I changed the air...

Hi guys. When I start my car the engine drops sharply to the front right (as if standing in front of car) which, to me, indicates a failed gearbox mount? It was mentioned as something to watch on my MOT. The thing is I have no idea how to replace it apart from jacking the car up and using a trolley jack to support the gearbox. I have tried...

Hello All,
Can someone tell me what the reasonable lifespan of a dpf on a 2014 Peugeot Expert 2.0 HDi van is expected to be? Van has clocked 122602 miles and the dpf warning symbol has come on with a message 'seek help from a garage' or something similar. The van was taken back to the dealer from whome it was very recently purchased ( 3months...

My wife started to use her car now that she has had two jags.
The rear brakes were in a poor way with sitting around doing nothing for a year.
I've replaced the discs, complete with bearing and speed ring and all brake shoes.
I retracted the calliper piston with a with a special tool I've used before, opening the bleed nipple, for the expelled...

Hi peeps, I'm having a problem with my car going into limp mode with p0405 have changed the egr valve and still no joy this code happened after the egr valve had been changed prior to that I was getting p3007. Any help would be appreciated. Also where can I get a proper scan tool/software for Peugoet. Is it the Planet or diagbox I need. Thanks

Please can I have part number for Intercooler for my van VIN VF3**************[VIN obfuscated, can be read by forum staff].

Thanks.

Peugeot 308 P9 posted service light for low level dpf fluid (eolys) just after filling up with diesel. From the Citroen posts it appears that I can drive the car until the dpf fills up. I can easily refill the eolys, but need to get access to Diagbox to reset counter. I'm in the process of purchasing diagbox + interface lead, but that may take a...

I have run my clone diagbox on my own 207cc and have found it does what it should. I was today trying to run an actuator test on a friend's 207SW, the ECU test and it kept throwing up a message saying 'Activation not possible' for all tests. I have tried the throttle butterfly and the variable valve motor. No joy. Same message The car doesn't...

A hot and sunny afternoon to you all,
Wife peugeot partner has the power fold mirrors, it appears the passenger one is a little out of sync as such and over extends by about 5mm when opened meaning the mirror is at maximum inner adjustment, Is it possible to to correct? Or is it a replacement mirror job?
Many thanks in advance
Timmo
Vin incase...

Pulled up outside house yesterday and when I looked into wing mirror it was folded in, same on nearside. It wasn’t folded in just before I pulled in cos I checked it. Now mirrors don’t fold in or out. No noise so just stopped working.
Any ideas where to start looking for fault ? Fuse ? Switches ?

My 406 2.1td has done this twice, have done 1000 km with the car since I bought it and this started yesterday. It shuts off during driving, but only now and then, after you can crank and start it right away and works fine. The first time I was a little scared and didn't look well at everything, I thought it would be lack of fuel, as I was close to...

Hi
Im looking for some guidance with a problem with my daughter 2008 207 1.4 8V manual. Having driven it with a coolant leak the head gasket failed and I have replaced it and had the head skimmed. New bolts were used and the thermostat housing on the side of the cylinder head was replaced which was the location of the leak. I have followed the...

hallo everyone

I searched a lot and I will try my luck her :)

I have a injektor problem and I need to change it ,just want to know how is the order of it if some one knows will be great
when im faced to the motor 4 cylinder from left to right ist 1 2 3 4 or 1 3 2 4 or ist opisit

thanks a lot

Hello,

I have a 2010 pug 207 1.4i. The car was doing random fail codes so after a while I found the problem that water ingress into ecu connector. My ecu is Valeo and engine code is KFT. My problem is that 2 pins from 2 connectors are rusted/almost gone.
From left to right ECU front view: connector 1 has pin F3 damaged, and middle connector A2.
I...

Can anyone supply a wiring diagram for the ECU for my 207 that won't turnover and is unresponsive? I've measured 5V at the water temp sensor, but without a wiring diagram I cannot follow up any further. Many thanks in advance. The VIN is VF3**************[VIN obfuscated, can be read by forum staff].

Hi Guys,

my 308 sw 1.6 hdi from 2008 have new fault :( high beams are always on, pull the fuse to swith of.

if i pull stalk to high beam i see blue indicator in dash to come on and off but lights are always on

anyone with the same problem?

i read on google that ptoblem can be bsm or comm2005...

Hi folks,
I'm new to this forum, just after a bit of advice please.
I've got a peugeot 806 2.0hdi manual yr2000 and the management light came on yesterday. I've scanned it with a cheap memoscan u480 and it came up with P0903, P0220 & P0335.
The car runs fine with no issues that are noticeable.
Am I waisting my time with this scanner?

hi to all
peugeot 3008 hdi how do you reset the dpf adative reset using diagbox v9.91
david

Hi all

Does anyone have any idea of where the other end of the mauve (VI) wire from the (5-pin) accelerator plug in a 207 Sport goes to?

My car's off the road at the moment (9 days now!) :( because of issues around the accelerator; my mechanic says the problem isn't the accelerator or the throttle unit (both have been changed), but the voltage...

Just FYI - tried the ACC out yesterday on motorway and conventional roads. Worked well and even shouted at me for not keeping my hands on the wheel and it kept the car in the correct lanes and braked perfectly. Only one gripe - After navigating roundabouts or being forced to slow down on slip roads the pick up back to high speed is way too slow if...

Hi,

I'm having trouble with my XUD7t in my 309. Suddenly one day spluttered and cut out at 70mph then wouldn't then restart. Would turn over but no fire. Eventually one random day it started again, so took it to work to have a look. As it was starting and running ok just replaced fuel filter, filter housing, leak off pipes and looked for fuel/air...

Could you put up a diagram for the rear outer wheel bearings and their part numbers for our 2013 3008 Hybrid4. cheers

Just bought a 2007 Peogeot as a first car for my 17yr old. Its currently a 'non-runner' but intend to use as a project to get him on the road. I dont have the history of the vehicle however the symptoms are as follow ....

Battery is good and has power
Turn the key and the ignition lights come on as expected
The dash shows an anti pollution fault...

I have just fitted a set of Michelin Primacy 3's to our 3008 and I had difficulty locating the locking bolt adaptor on the osf wheel. What I found was a cracked ring.
1625940188596.jpg
1625940188591.jpg

has anyone had this before and can it be caused by using an impact gun?

Hi all, new member here.
The front blowers in my 5008 have stopped working suddenly. The ones for the rear passengers are fine though. I've had a look under the dashboard and checked the resistor that's attached to the fan but can't find any obvious signs. Any help or advice would be greatly appreciated. Many thanks