French Car Forum

I'm trying to locate the earth points on my 2013 207SW 1.6 diesel (VF3**************[VIN obfuscated, can be read by forum staff]) ... I'm investigating what seems to be the rather too frequent blowing of rear light bulbs and want to try to rule out poor earth connections.

I'm aware of the excellent crib sheets for interpreting electrical diagrams ( but was wondering ... are the diagrams...

Nox Sensor P220A Fault Code

I have a 2016 Partner Tepee 1.6 Blue HDI DV6FD engine.

I now regularly get this fault code. P220A nox sensor 1, bank 1 supply voltage circuit malfunction. It is easy to delete the code with a cheap Elm reader or with Diagbox. I am looking for input from members who understand this kind of intermittent fault.

So it...

Hello all
does anyone know where I can get the rear brake splash plates for my 2002 607 HDI?

The OEM numbers are 4212 95 and 4211 95.

Regards

Ken

Hello all,

Ever since I purchased my Peugeot Partner Electric, I have had some intermittent problems with the Chademo fast charger. Sometimes it works, sometimes it doesnt and Sometimes, after it starts charging, it can randomly disconnect.
When I took it to the local Peugeot garage, they said that they couldnt see any fault codes :rolleyes:

I...

Hi,

After weeks of being unable to access mode due to ambient conditions I am told that maybe one of the 12v batteries needed to be fully charged.

Can anyone tell me where the second battery is located? The one in the engine compartment is showing 12.67 volts without dropping.

Regards
Brian

So my thp175 has developed a fault with the a/c. I have 3 dtc codes
F994: fault in a/c compressor clutch control
F995: fault in a/c compressor variable control circuit
715c : a/c pressure information

I have replaced compressor and condensor, have had the system regassed correctly with a 30 minute vacuum. There is no leak in the system.
I...

Does anyone know if the door seals on later cars, say 5008, are a similar profile as used on the 307?

My 307 need new front door seals, can't use rear ones from the breakers because they are a couple of inches shorter. Got me thinking about whether I could use some rear door seals from a later car, which is likely to be generally larger door...

hi

really desperate for any help with a 2018 2.0 blue hdi boxer. Yesterday, my android head unit restarted a few times for no reason and the airbag warning light triggered. Then power to head unit went completely along with permanent air bag light, random alarm not working warnings, no headlights low or high beam (I have side lights and...

Hi all,

Well, after 15 1/2 years the original battery on my wife’s 2010 207 1.6 VTi finally died (maybe we could claim under warranty 😄😄😄). It had been entering economy mode regularly when the remote didn’t work.

Battery replaced and fully charged before fitting. I’ve done 2 BSI resets, but the car still goes into economy mode a few minutes...

2013 1.6 HD Partner

Trying to determine if I have a faulty MAF sensor. I did a scan of the values at idle and they averaged about 10 g/s

Is that too high for this model?

I admit it - I don't know where to start looking.

If the battery is not connected, it will retain almost full charge for a few weeks.

However, if I connect the battery and don't drive the car, the battery will be drained within 4 days. If I drive the car, it is even worse! The battery will probably be drained the same day. But that will depend...

Hello everyone, I need a little help if someone can give me some ideas, please.

this is my first post here and I've looked around the forums and read a lot of helpful information but nothing relating to my current issue. If there is a post there please link to me and ill remove this one.

Problem: dual climate air condition
No hot air coming...

I have a 2012 508 Gt (2.2HDI) that has the JBL radio with amp in the boot. It went silent for hours/days/weeks/months at a time then worked perfectly again.
I have replaced the amp unit and each time it works perfectly for a while, then goes silent again, but the head unit gives every indication of working.
We noticed that when it is silent, the...

Can anyone tell me the oil capacity of the gearbox on my Boxer motorhome. There is no level plug, just drain and fill. I want to change the oil. The VIN No is VF3**************[VIN obfuscated, can be read by forum staff] Thanks.

please help bought a peugeot 3008 thp 1.6 petrol from a auctin site but its in a limp mode the car starts ok revs upto around 4000rpm and drop straight back to 3000 very quickly turn off the car start again and does the same thing revs upto around 4000rpm and drop straight back to 3000rpm very quickly and the car does not drive above 25 mph
this...

I’ve got a 306 2.0 HDI, I’m missing an injector pipe, one end is 14mm nut(at the injector) and a 17mm nut (at the rail), can’t seem to find one anywhere, tried ordering new keep getting the pipes with 14mm on both ends, any help appreciated

Hi hope someone can help. 100 miles Post a service (oil, oil filter, gearbox oil, fuel filter) the car is going into a limp mode then stalling with the stop warning. Error code is f40a. No engine warning light. Oil check on dash is ok . Oil level is good.
from cold will run fine for 5 mins. Once warm and revved will sometimes get amber triangle...

I am trying to replace the touch screen radio with a large touch screen, the form on e bay says this radio will fit my car, put the power harness has a different socket then the one on the car ? I have a bosch radio, can I buy another power socket that will fit ?, it is one of the Chinese large screen all singing and dancing, can any help ?

My neck unit is has to be replaced is this a common complaint with this car any help would be most appreciated.

Hi. I have a fault on a 2004 Peugeot 206. The ABS light comes on randomly. It can happen when stopped or driving. I did a scan and the fault is description is

ABS or ESP ECU
Intermittent fault. ABS/ASR (traction control) recirculation pump. Pump locked, CO, CC- or CC+

Would I be right in thinking the fix is to replace the ABS unit?

Hullo,

This is a real puzzle for me - see if you guys can solve it!

Following on from a previous post - keep getting P1490 - driving condions not met. No other DTCs at all. This is a 2017 boxer with 2.2tdi Puma engine, with only 12,000 miles on the clock. It's a horse box that I've just brought, with no history. I can see that it's got an after...

Hello every body

Iam planing to DIY manifold and air intakes manual cleaning because my car is suffering of self ignition before spark and knocking.( with a service word appear in the board dash with a limited performance)
Pointing here that my engine is 1.2 i thp 130 (eb2dts) and my car is peugeot 308 t9 2016.

Could any one help me if there...

Hello good people,

I drive Peugeot 508 2.0 HDI 163 Hp 2011. With approximately 330000 km, but it behaves like it has 120000 km.(Maybe i revert km to 120000 on cluster(joking :D)).Only problem that i have now is occasionally Engine management light, Diagbox says this with error P0471:

P0471 : Particle filter differential pressure sensor....

Hi all, I am looking for some help with my radio unit. It suddenly stopped working and all i hear from it is a noise from it as if it has a CD stuck in it. The navigation head unit screen opens and closes as normal but no display and the radio wont even turn on. Hope some one could help me with this

Ive looked high and low and found several different numbers for the Nm torques for the XUD 7 diesel non turbo . Some say 15 Nm and others say as high as 22 Nm which i say is too high !
the thread is 12mm x 1.5 pitch if i am correct . I,m not going to gorilla on a glow plug that size to 22 Nm !!!
Can someone point me to the peugeot engine specs...

Hi!

Thank you for letting me join your forum! I have recently purchased a 2017 Boxer Floor Cab 335 L3 HDi 150. It's actually a horsebox, and was attracted to it as it is in great condition and very low mileage at 12,000 and drives fine.

However, it's started tying to perform a DPF regen - yellow light comes on and message about regen starting. I...

I may have posted this but cannot remember !
I have a series II 1995 two door 205 xud7 non turbo version . On the front are discs from another vehicle , peugeot i think ? the rear appears to be original standard.
I want to discard all the old brake systems front and rear with new parts .
But the discs and calipers on the front are not 205 original...

Car started to get a random misfire a few weeks ago but it would go away

I checked all the connectors etc, pulled ECU plugs just in case it was a bad connection (see my old post

Now its permanent with Diag reporting Codes P0355 5 ignition coil control, P1336 Unspecified combustion misfiring, P1341 misfiring on cylinder 5

Cylinder 5 is the...

Hey All,
I am looking to retrofit Cruise control and speed limiter functions in my 2011 Partner Tepee S 1.6hdi 9HN, however I have seen some reports the in the UK the ecu on this engine model doesn't support it.
My Vin is:
VF3**************[VIN obfuscated, can be read by forum staff]

Before ordering or installing anything I know to check:
1.That the instrument cluster shows the outline...

Can the cooling fan switch on temperature be changed from 90 to 84 with the computer?

The reason I'm asking is that it would solve my 508 automatic sticking problem on higher temperature. It only does it in town in the summer time, when it gets to 90.

Hi guys.

So, i'm sat scratching my head. I have had the eml on, comes and goes and i've pulled two codes - as above p2173 and 1499 for something called an air mixer.

Now, i've done some small reading and think this item is the same as the air doser from the euro 4 psa 1.6 engine, the butterfly valve in the intercooler system. But can anyone...

Good evening people,

Is it possible to obtain a full wiring diagram for a MkII 405 2.0 petrol auto? Or especially as it relates to the air con system. I am determined to try and fix my intermittent A/C.

VIN is VF3**************[VIN obfuscated, can be read by forum staff]

Thanks

Hello to All,

I was wondering if someone would point me to the right direction as sometimes I am finding this error when scanning the car with Diagbox. Normally I don't see any warning on my dashboard.
Please see picture error from Diagbox.

Something regarding the One-touch control switch S1 and One-touch control switch S2 .
I was searching the...

Hi everyone, I’m having a serious issue with my Peugeot 5008 (66,700 miles) and would appreciate any advice.

10 days ago, the car wouldn’t start — brake pedal was very hard, and dash didn’t stay on. I suspected the battery, charged it, and it worked. But now the same issue is back.

Symptoms:
Car won't start.
Brake pedal is rock hard.
Parking...

Hi, I have a Vauxhall Mokka E with a complete front end replaced with new sensors radar etc.
When I took the car on the dashboard I saw the collision system fault but that was fine as the Radar bracket etc was damaged..
Now we replaced everything and the car runs but we still have the issue, the radar is made by Stellantis and is say Peugeot on it...

Hi all,
Newbie here, need to pick some brains :
I have a peugeot boxer motorhome
1999
1.9td xud
Sometimes when I pick it up from storage it starts up ko.orobs but when I drive it seems very underpowered, heavy black smoke ( more than normal ) and I hear a fluttering noise which sounds like it's coming from the exhaust as I rev out just before I...

Anyone shed some info, I’ve got a 2010 Peugeot partner van 1.6 hdi 96 bhp had a knacked motor, bought a donor 307 1.6 hdi 110 swapped motor over complete swapped fuse board plugged in fired up, I’m having issues with power runs starts perfect but eml light on, got anti pollution fault. Engine Managment fault & code coming up for egr, peddle sensor...

Hi I have a Peugeot 3008 hybrid 4 2013 and it has a rotational noise from the rear right hand side and it is not the wheel bearings and it’s not the reduction gear or motor as they have been replaced and the same noise was there before changing the motor and reduction gear I have replaced the right hand side drive shaft and the noise is a little...

Car is a Peugeot 307 1.6 16v petrol, TU5JP4 engine, 90k miles.

Has a bit of hesitation/judder on the overrun. Happens on a warm day when trying to hold a lowish speed of say 50mph on a slight downhill. Pulls ok at normal low throttle openings. Doesn't feel like just one cylinder missing, feels more like two or perhaps the throttle valve...

Hi there.

I just bought a 2013 Peugeot 508 GT, and I was thinking about updating the maps.

Does anyone have the latest maps avaliable for Europe?

Thanks in advance

m

Hi Team,

New member, long time forum reader here!

I have recently bought a 2007 Peugeot 207cc which has the AL4 Gearbox- I have replaced the solenoids following the error code P1167 and set the correct oil level following the procedure (60 Degrees, Level Ground) but, I am still getting an audible thump when changing gear followed by the Gearbox...

Hi, I have a Rifter HDI 1.5, 21 plate, 50 k on the clock. I currently have a faulty EGR valve, due to be replaced shortly. (Spoticar refused warranty) just recently it threw up an error code P2002, DPF efficiency below threshold bank 1. Is this critical or will a good hot run up the motorway be all it requires ?

Hi All, I'm new to the forum and in need of some help. Hopefully someone may be able to shed some light on my fault. Vehicle is Peugeot Boxer 2.2 HDI L1 H1 4HU 2015. I have a exhaust gas temperature too high fault P2428. Looking at live date the temperature of the sensor at the dpf is 860 degrees with a cold engine (overnight rest), I've tested...

Hi all,

Rumours that PSA will change (again) the oil spec.. Now, from 0w20 to....?
Anyone knows anything?

Hi everyone,

I’m struggling with a persistent P0101 (MAF/air flow issue) on my 2.2 HDi Boxer (120 hp, 2008).

I’ve already replaced the MAF sensor (no change).

I dismantled and checked the entire intake system, but found no obvious leaks.

MAP sensor was also cleaned and later replaced.

Despite this, the error keeps coming back.

Live data...

Hi people I’m hoping someone can help me with a problem that’s been plaguing me since march!!

Bought van as its an old wheelchair adapted vehicle and converted to a basic camper to do festivals in - perfect

Bought it off an old woman, trusted her, paid her, when I got there it’s in limp mode and all of a sudden she can’t be contacted. So I drove...

Hello colleagues,

I have a Peugeot 308 SW 2.0 BlueHDI 150 HP from 2015 and recentely I had an issue with the particle filter(it couldn't regenerate by itself and went to the Peugeot to take it down and get cleaned). After 2 days I got UREA Warning lamp On and also the Engine check was on, and tought that I need to refill the AddBlue tank which I...

Helo everyvone
-Peugeot 206 1.4 HDI 2006.
erro codes p1352,p0104 .

The car starts nicely and easily in winter and summer.
New air mass meter, new boost pressure meter, new egr, new intake air temperature sensor.

But the car still shuts off...

the intake air mass is 0/mgs...as if the ECU doesn't see the MAF signal(If I unplug the air flow meter,...

Ma P 607 2.2 HDI, année 2003, affiche 540 000 km et est comme neuve. J'ai un problème avec l'écran : les chiffres et les lettres disparaissent (décoloration, déchirure). Comment puis-je résoudre ce problème ? Puis-je en trouver un neuf ?

Hi again I have a Peugeot 307 1.6 hdi 2006 and the car starts fine from cold and runs ok but when the engine warms up to 70-80 degrees then you switch off and leave for a few mins 5-10 mins engine doesn’t want to start again the fuel pressure in parameters on diagbox shows 125 bar and the ref pressure is at 286 bar and obviously engine will not...