French Car Forum

So, I've been doing some quite in depth messing around with OBD on my 2008 207cc 1.6Hdi.
The diagrams in ServiceBox indicate that the 'CAN IS' is attached to a 250kbps CAN bus on the J1962 standard pins 6 & 14.
Also... it indicates an ISO14230 'K Line' directly connected to the engine ECU on J1962 pin 7 and a non-standard 'DIAG CAN' at 500kbps...

So now the nights are creeping back in my little 207 has one bulb out . The heater panel right had side isnt lit . Here's a picture of the housing . Turns out I've only black cap not the white , anyone got any ideas to its part name or numbers.

Why not post up here your bulb and or any references to part numbers and bulb codes ...might help some...

Hi Team,

Last night when driving home, I noticed a very strong exhaust smell through the cabin vents which was so bad I had to turn the re-circ function on to stop the smell from coming through from the engine bay.

I have since checked and it looks like there are exhaust fumes leaking from the manifold gasket.

I have done some research but I...

We have a 2009 1.4 VTi on 75k, it is rough at idle and the revs hunt. Unfortunately, the car has been off the road for a while and I don't know anything about the back story except that it has a full service history. I have given it a service anyway but that has not helped.

It has a code for the Cat of P0420. Obviously it could be the Cat, but it...

Hello everyone. So I have peugeot 2008 with 1.2 eb2dt hn01. Long story lost oil pressure and now has scoring on camshafts and crankshaft, so basically engine is gone. The question is what is the difference on engine codes? There are so many different ones,and I can't find any info. I got offered engine from 2022 citroen that has only done 1100...

I'm wondering if my newly aquired Boxer has a timing belt or chain - and at what point I should look into whether it's time for a replacement.

2.0 TDI 130 PS / 96 kW adblue, euro 6
Production date: 27/9-2016

It has driven 102.000 km and was first registered 02/2017. All services has been done on time.

Thanks!

2011 Peugeot 308 1.6ehdi with stop/start

Hi all have a strange intermittent charging issue.

Car normally charges at 14.7volts. However occasionally the voltage will drop to 12.6 roughly. However when on overrun or strangely activate wipers, the voltage goes back to normal, then drops down when driving or at idle. No fault codes present in bsi,...

Hi everyone,
my 5008 keeps draining the main battery (drops from 12.4 V to 10.8 V in a few days).
I can hear a faint beeping or buzzing after onneting the battery. I guess its from the alarm siren.
I did looking for it but cannot find, guess will be hidden under windshield.
I would like to disconnect it, but I’m not sure if it will start sounding...

Hello. I have a problem here. There is a problem with the connection to the unit ESP/ABS. I need to know the connection of its bases and I do not have access to its diagram. There is probably a unit failure. Do any of the administrators or people have access to the diagrams?

MY VIN:VF3**************[VIN obfuscated, can be read by forum staff]

hi

f!

Hello friends! I have a 407 coupe 2.7 hdi from 2007. For almost a year I have been struggling to start it and I can't. The car stopped while driving on the highway. I have no communication with the Ecu, it doesn't crank.
I measured the Can network at the obd plug and as a result I have: can H 0v and go to ground and can L is almost identical...

Whats this all about ? They look like a bulldog. I keep seeing these when I'm out and there starting to make me like them . Ive me 308cc do i move this on for one ? Help 😆

Hi all , I have a misfire on cylinder number 1 , I swapped coils from 3 to 2 and 1 to 2 as I found out no 1 is at flywheel side , the fault didn’t transfer , so it’s either wiring , plug or engine computer , codes p2303 p0053 p0054 and p0420 , it’s also using engine oil , any wiring diagram for coil to ecu , is this a common problem, thanks

Hi guys,
Can somebody help me obtain a copy of the above manual if it exists. Can pay a reasonable cost. Really need some info on the puretech 1.2 EB2FA engine as it looks like i am going to have to do a rebuild over the winter.
Thanks

Baz.

Hi guys, can anybody help me out please? In a nutshell, two rotations of the Engine Flywheel End = One Rotation of the Camshafts (it seems?).
I have had the Camshafts off and replaced the Valve Seals using 'the rope method', ie, turning the engine to compress the rope at TDC to stop the bloody valves falling out. It worked great but now there is...

Good afternoon all,

Peugeot Partner 58 plate 1.6HDI

So, the wife calls me up to say the van will turn over but not start, soon after she managed to get it running albeit a warning triangle on the screen. Read up and it said Ad Blue so got some, looked for the tank down by the left side of the engine bay (Battery side) but there is nothing there,...

can some2 tell me when torque is connected what should the boost clock on the app be sitting at thanks in advance.

If it's not one thing it's another!!
My Peugeot Expert 2.0 2016 Mkii decided to flash up a low oil pressure warning this morning, very briefly after a cold start and then a few seconds later once moving.
Stopped, checked oil (only a few hundred miles and plenty in it) and restarted with no further warnings.
I'd been through a fair bit of water a...

MY PEUGEOT PARTNER TEPEE E-HDI 1560cc. semi auto 6 speed 2012 vin no. VF3**************[VIN obfuscated, can be read by forum staff]. HELLO, IM NEW TO THIS SITE, I HAVE A FAULT WITH MY CAR, WHEN PULLING OFF FROM COLD, SOMTIMES HOT, IN 1ST GEAR, THE CAR JUDDERS, CANT STAND IT ANY MORE, WHEN DRIVING ITS OK, WHEN IN 4TH TO 5TH GEAR, IT GOES LIKE HELL. HAD CAR FOR 1 YEAR NOW, BUT CANT FIND WHAT...

Good afternoon!
The garage has diagnosed a faulty BPGA (they have called it Battery Protection Module - which I suppose is the same) on my 2016 Peugeot 308 SW GT?Line, and I’ve been quoted a high amount just for the unit fit + coding/?programming. Before I commit, I’m trying to find out whether the reprogramming/coding is always required?or...

Hi Everyone,

I have winter and summer alloy wheels for my Peugeot and I have no issues with interchanging them(bolts are fine).
The problem is that I have purchased a spare wheel size 16 which is from steel (not alloy) and I would like to know if i need 4 different bolts for it ?
As far as i understood from checking the forum the bolts for alloy...

Hi! I have been trying out various used PSA vans lately and how now found a 2017 Boxer with the 2.0 130 PS euro6 engine which has done 100t km - it looks very promising.

I was wondering if anyone could help me with some tips on what to look out for when I test it. Of course I'm going to check if there is a log of regular services and look for...

Every blinking time...... replacing the top mount on my daughters 208 (2014 1l manual) and I've tied the driveshaft back but still I look away for 2 seconds and half the contents of the gearbox is now on the driveway.
I know I'll need to completely drain and refill but could anyone please advise grade and quantity of oil needed?
Many thanks

Peugeot 307 SW with fixed panoramic roof.

Had some heavy rain last week when the car wasn't used. Next outing, with air con in use, found water coming from the footwell vents both sides with the RHS more affected than LHS, in fact it was soaking.

I haven't pulled the carpets yet to check the drain. I removed the grilles under the scuttle cover...

Hi,

My van was showing the eml, service and adblue lights with nox sensor related codes. It then started producing acrid white ammonia type smoke from the exhaust. I pulled the SCR system relay and fuse to stop the smoke temporarily and noticed the urea injector looked a bit crusty.

I decided to replace both at once, same part numbers. vitesco...

Hi everyone,
I'm new here and I need some help .. Hope someone had similar problem or enough knowledge to resolve it ..
The car in question is Peugeot 5008, 1.6 blue HDI, 88 kW, 2015 ..
Few days aho I started it and it was rough idling and it shut down .. Again same thing.. third time ot started but no rpm on dashboard, idling approx 1200 rpm, eps...

Hi
I have a '99 406 coupe V6 and I'm trying to find the bracket/cap that goes over the suspension arm bush ( left rear). The original has finally rusted through and spat the bush out but I can find replacement bushes OK but not the bracket for it. The garage I normally use can't find any, Peugeot don't supply them anymore and the only thing that...

Anyone know if it is possible to remove the rain/light sensor from a breaking car and fit it to a car which didn't have that installed originally? I realise I will also need the steering wheel stalks but presume these can be unclipped somehow can they?

Tried removing one of these sensors from a Citroen but it appeared to be bonded solidly to the...

Hello got a strange issue with the emissions at low revs (1000-2000 revs) if I press the throttle down slowly emissions are 0.03 and will hold that all the way to 5000 revs but when the throttle is blipped up to 2000 revs like it is done in mot test the emissions will go up to 0.70 or maybe just above, the limit on the car is 0.51 this is causing...

put new turbo and wastegate now getting P2562 not getting enough turbo charge on the torque app the boost clock says .29 is this right or should be higher on tickover.

I’ve replaced the rocker cover gasket on this car and been having issues getting to run smooth at the start with multiple codes popping up. Now I’ve managed to clear everything and had taken it for a drive.
But after a while after driving the car seems to get boggy or lose power as it just gets to around 2k revs and the whole car shutters, maybe...

Hello :)

I'm thinking of buying a Peugeot 508 from 2014, I've got the VIN and I would like to get some information about the car (trim level, options, etc).

VIN NUMBER: VF3**************[VIN obfuscated, can be read by forum staff]

Thank you very much!

good morning, I'm trying to activate the rain sensor on my peugeot 208 2024 active model which doesn't have one, I bought the original NEW compatible spare part, I attached it to the glass without problem and to the already existing wiring, then with the coding tools I activated the 236D rain / light sensor zone in bsi on the network but I...

Hello, is there a document containing the 308 t9 front pdc assembly diagram and necessary materials?

Hello.
I know it's probably impossible to diagnose things online, but I'm going to try, as someone unfamiliar with 308's and turbos.

I'm a new proud owner of a Peugeot 308 2016 1.2 Gt Line.
It's a beautiful car!

I've had it since Saturday, and twice now, when I've been reversing the car to park, I've heard a loud whine for like 1-2 seconds....

Hi guys,
First of all thanks to the people who run this forum!
My 2018, 2008 1.2 Allure has a problem? Advice needed please.
I changed the cambelt. Now there is blue smoke coming from the exhaust. Seems worse after pausing at traffic lights??
It was fine before.
Never changed a cambelt before but I think I have messed it up, but not sure if this...

Hello, can I find out what extras my car came with when it left the factory?
VIN:VF3**************[VIN obfuscated, can be read by forum staff]

I've got a permanent P13C2 error on my 3008. Does anyone have more description of this fault code and ideas on where to troubleshoot first?

Having changed the MAP sensor on my petrol 1.6 16v (TU5JP4 / NFU) I now seem to have a raised idle: with the old sensor was about 800rpm, now 975rpm.

Diagbox readings at idle:

?Ignition:

Speed: 960?
Battery: 14.2?
Ignition advance: -10.5?
Charge time 1/4: 2.7?
Charge time 2/3: 2.7?
Air intake:?
Motorized throttle status: idling?...

Hello colleagues.
On the car in the description, I have a problem with the 6-speed manual gearbox, which remained stuck in gear 1. After I dismantled/reassembled the gear shifter, I tried to reset the gear adjustments in the gearbox and I think I forced the selector shaft on the gearbox, which remained stuck in gear 1. At the same time, the other...

I'm trying to locate the earth points on my 2013 207SW 1.6 diesel (VF3**************[VIN obfuscated, can be read by forum staff]) ... I'm investigating what seems to be the rather too frequent blowing of rear light bulbs and want to try to rule out poor earth connections.

I'm aware of the excellent crib sheets for interpreting electrical diagrams ( but was wondering ... are the diagrams...

Nox Sensor P220A Fault Code

I have a 2016 Partner Tepee 1.6 Blue HDI DV6FD engine.

I now regularly get this fault code. P220A nox sensor 1, bank 1 supply voltage circuit malfunction. It is easy to delete the code with a cheap Elm reader or with Diagbox. I am looking for input from members who understand this kind of intermittent fault.

So it...

Hello all
does anyone know where I can get the rear brake splash plates for my 2002 607 HDI?

The OEM numbers are 4212 95 and 4211 95.

Regards

Ken

Hello all,

Ever since I purchased my Peugeot Partner Electric, I have had some intermittent problems with the Chademo fast charger. Sometimes it works, sometimes it doesnt and Sometimes, after it starts charging, it can randomly disconnect.
When I took it to the local Peugeot garage, they said that they couldnt see any fault codes :rolleyes:

I...

Hi,

After weeks of being unable to access mode due to ambient conditions I am told that maybe one of the 12v batteries needed to be fully charged.

Can anyone tell me where the second battery is located? The one in the engine compartment is showing 12.67 volts without dropping.

Regards
Brian

So my thp175 has developed a fault with the a/c. I have 3 dtc codes
F994: fault in a/c compressor clutch control
F995: fault in a/c compressor variable control circuit
715c : a/c pressure information

I have replaced compressor and condensor, have had the system regassed correctly with a 30 minute vacuum. There is no leak in the system.
I...

Does anyone know if the door seals on later cars, say 5008, are a similar profile as used on the 307?

My 307 need new front door seals, can't use rear ones from the breakers because they are a couple of inches shorter. Got me thinking about whether I could use some rear door seals from a later car, which is likely to be generally larger door...

hi

really desperate for any help with a 2018 2.0 blue hdi boxer. Yesterday, my android head unit restarted a few times for no reason and the airbag warning light triggered. Then power to head unit went completely along with permanent air bag light, random alarm not working warnings, no headlights low or high beam (I have side lights and...

Hi all,

Well, after 15 1/2 years the original battery on my wife’s 2010 207 1.6 VTi finally died (maybe we could claim under warranty 😄😄😄). It had been entering economy mode regularly when the remote didn’t work.

Battery replaced and fully charged before fitting. I’ve done 2 BSI resets, but the car still goes into economy mode a few minutes...

2013 1.6 HD Partner

Trying to determine if I have a faulty MAF sensor. I did a scan of the values at idle and they averaged about 10 g/s

Is that too high for this model?