French Car Forum

Please can I have part number for Intercooler for my van VIN VF3**************[VIN obfuscated, can be read by forum staff].

Thanks.

Peugeot 308 P9 posted service light for low level dpf fluid (eolys) just after filling up with diesel. From the Citroen posts it appears that I can drive the car until the dpf fills up. I can easily refill the eolys, but need to get access to Diagbox to reset counter. I'm in the process of purchasing diagbox + interface lead, but that may take a...

I have run my clone diagbox on my own 207cc and have found it does what it should. I was today trying to run an actuator test on a friend's 207SW, the ECU test and it kept throwing up a message saying 'Activation not possible' for all tests. I have tried the throttle butterfly and the variable valve motor. No joy. Same message The car doesn't...

A hot and sunny afternoon to you all,
Wife peugeot partner has the power fold mirrors, it appears the passenger one is a little out of sync as such and over extends by about 5mm when opened meaning the mirror is at maximum inner adjustment, Is it possible to to correct? Or is it a replacement mirror job?
Many thanks in advance
Timmo
Vin incase...

Pulled up outside house yesterday and when I looked into wing mirror it was folded in, same on nearside. It wasn’t folded in just before I pulled in cos I checked it. Now mirrors don’t fold in or out. No noise so just stopped working.
Any ideas where to start looking for fault ? Fuse ? Switches ?

My 406 2.1td has done this twice, have done 1000 km with the car since I bought it and this started yesterday. It shuts off during driving, but only now and then, after you can crank and start it right away and works fine. The first time I was a little scared and didn't look well at everything, I thought it would be lack of fuel, as I was close to...

hallo everyone

I searched a lot and I will try my luck her :)

I have a injektor problem and I need to change it ,just want to know how is the order of it if some one knows will be great
when im faced to the motor 4 cylinder from left to right ist 1 2 3 4 or 1 3 2 4 or ist opisit

thanks a lot

Hello,

I have a 2010 pug 207 1.4i. The car was doing random fail codes so after a while I found the problem that water ingress into ecu connector. My ecu is Valeo and engine code is KFT. My problem is that 2 pins from 2 connectors are rusted/almost gone.
From left to right ECU front view: connector 1 has pin F3 damaged, and middle connector A2.
I...

Can anyone supply a wiring diagram for the ECU for my 207 that won't turnover and is unresponsive? I've measured 5V at the water temp sensor, but without a wiring diagram I cannot follow up any further. Many thanks in advance. The VIN is VF3**************[VIN obfuscated, can be read by forum staff].

Hi Guys,

my 308 sw 1.6 hdi from 2008 have new fault :( high beams are always on, pull the fuse to swith of.

if i pull stalk to high beam i see blue indicator in dash to come on and off but lights are always on

anyone with the same problem?

i read on google that ptoblem can be bsm or comm2005...

Hi folks,
I'm new to this forum, just after a bit of advice please.
I've got a peugeot 806 2.0hdi manual yr2000 and the management light came on yesterday. I've scanned it with a cheap memoscan u480 and it came up with P0903, P0220 & P0335.
The car runs fine with no issues that are noticeable.
Am I waisting my time with this scanner?

hi to all
peugeot 3008 hdi how do you reset the dpf adative reset using diagbox v9.91
david

Hi all

Does anyone have any idea of where the other end of the mauve (VI) wire from the (5-pin) accelerator plug in a 207 Sport goes to?

My car's off the road at the moment (9 days now!) :( because of issues around the accelerator; my mechanic says the problem isn't the accelerator or the throttle unit (both have been changed), but the voltage...

Just FYI - tried the ACC out yesterday on motorway and conventional roads. Worked well and even shouted at me for not keeping my hands on the wheel and it kept the car in the correct lanes and braked perfectly. Only one gripe - After navigating roundabouts or being forced to slow down on slip roads the pick up back to high speed is way too slow if...

Hi,

I'm having trouble with my XUD7t in my 309. Suddenly one day spluttered and cut out at 70mph then wouldn't then restart. Would turn over but no fire. Eventually one random day it started again, so took it to work to have a look. As it was starting and running ok just replaced fuel filter, filter housing, leak off pipes and looked for fuel/air...

Could you put up a diagram for the rear outer wheel bearings and their part numbers for our 2013 3008 Hybrid4. cheers

Just bought a 2007 Peogeot as a first car for my 17yr old. Its currently a 'non-runner' but intend to use as a project to get him on the road. I dont have the history of the vehicle however the symptoms are as follow ....

Battery is good and has power
Turn the key and the ignition lights come on as expected
The dash shows an anti pollution fault...

I have just fitted a set of Michelin Primacy 3's to our 3008 and I had difficulty locating the locking bolt adaptor on the osf wheel. What I found was a cracked ring.
1625940188596.jpg
1625940188591.jpg

has anyone had this before and can it be caused by using an impact gun?

Hi all, new member here.
The front blowers in my 5008 have stopped working suddenly. The ones for the rear passengers are fine though. I've had a look under the dashboard and checked the resistor that's attached to the fan but can't find any obvious signs. Any help or advice would be greatly appreciated. Many thanks

Hi Guys

Peugeot 307CC 2008 HDi Diesel
VIN VF3**************[VIN obfuscated, can be read by forum staff]

I have an ABS brake problem that I'm struggling to fix and apreciate any help I can get.
Below are the error codes.

C1331 Front Right Wheel Speed sensor signal fault
C1326 Rear LH Wheel Speed sensor signal fault
C1387 Fault wheel speed sensor asleep

The car was fine before all the...

Hi friends
I have discovered 2 X relays located under the bsi.
Behind the facia on drivers side.
Does anyone know what these are for.

Also there are 3 relays on the slam panel in a plastic box.any ideas what these are for
thanks

I recently fixed the blower motor speed control on my 406 Estate 2.1TD. It would only work at max speed setting, all other steps the motor wouldn't even turn on. All first research I did pointed into direction of the blower motor speed control module (which in this model is fixed to the motor itself, it's the half moon two-transistor thingie which...

Theres always wet oil in the places shown on the photo below, and has been since I got the car 3.5 years ago, but weirdly it doesn't lose any oil. Anyone any idea where it might be coming from please?

Thanks very much

Whilst doing some maintenance on the 807 I came across two zipped tied wires at the front of the car.

I've attached pictures of coding for them in the hope that you lovely FCF boffins can tell me what they are.

Secretly hoping it's the plugs for the front parking sensors 🤔

Hi everyone my names nigel im from Norfolk I hope your all well.

I've came here hoping someone could help me with a possible problem I have with my 2016 gt line 1.6 diesel.
I recently had a issue with the front left strut top mount making noise, so being a fairly hands on guy decided to change both front shocks and all top mount components also...

Hello everyone
I am looking to increase my range of scanners.

Especially now I am looking to repair more Peugeot and citroen makes.
I have seen on Ebay various PP2000/LEXUS 3?
equipment all varying in price and promises.

Is there any advice on which specific PP2000/Lexus3 I should buy and from who.
Sellers mention Gold edges boards.samsung...

Hi all, haven't been on the Pug forum yet... And here I am asking a daft question #-o

A mate wants his 3008 rear caliper changed. Easy.... Except for the effalump in the room, the e-brake!

Never done one of these before so before I make a fool of myself, my 1st question is, can I use my Lexi/Diagbox to wind the motor back, change the caliper...

I am trying to find the gearbox code for my peugeot 207, using servicebox with an account seems to be difficult to find the basic information without a subscription. Does A7F 2 22A12A narrow it down via the parts list or is it best to go directly off the vin code?

Hiya all,

The front right tyre pressure sensor keeps going off. From what I can tell this is a very common issue with Peugeot's?

They are around 18 quid for a replacement sensor that's 433 MHz. Do they have to be paired with the car or do they auto connect?

Secondly is it worth the hassle or should I just get someone with Peugeot planet to...

hi to all
the adblue pump has failed and i made enquires and was told that i would have to replace the tank my question is can i buy just the pump or could the pump be repaired
david

Hi I have a 2006 207 that won't turn over.

The car is now in economy mode, plus signals a depollution fault and ABS braking fault. With the key in the ignition and the door open it beeps to remind you to remove the key.

The car failed back in March and I've looked at it and an auto-electrician has looked at, but with no joy. I'm now having a...

hello everyone.

I bought a 3008 a few months ago from a person close to me, knowing that I had the engine light and Urea access.
I bought it thinking it would only needed to top up the adblue.....
after purchase i checked the adblue tank, it was almost full. filled to the top.
got the same errors even after driving the car for a few days
after...

Had my 1.6 hdi 508 estate delivered today 142 000 miles
Checked over noticed radiator tank lol.
Topped up
Drove about 20 miles on test drive
Returned home
Header tank down to min again
Could hear air escaping from cap.
Does this mean head gaskets gone
No smoke from exhaust.
So if it is its not leaking from exhaust port.. Idk??
Help and advice...

Hello everyone.
After accident with my car(damaged front bumper) my car is going nuts. Abs, handbrake, gearbox failure. I have checked the wires going from abs to ecu and I found couple of them damaged. After repairing wires problem is still here.
I have read topics including famous blue wire going from Fuse box to abs. I've checked abs connector...

Hello the stalk arm won't bring on the fogs no lights come on for them on the dash I have had it on pp2000 I can activate the rear fogs on that but not the front ones anyone come across this problem? The bulbs look fine on the front

Hi All,

I’m looking for advice regarding a NOx sensor problem on my Peugeot 2008 Gt Line Blue Hdi S/S.
The car was first registered in May (UK) 2016 and has covered 53K miles.

There is some history to this and I’ll try to keep it short...

I’ve owned it for approx 18 months and drive less than 5,000 miles per year.
When I bought it, the dealer...

Hi, I bought a 2007 Peugeot 206 for my children who have recently got their driving licenses. The car worked fine for maybe a month but then from one day to another it wont start. It just cranks but nothing happens.
There is is no spark and the plugs are dry so it seems like no fuel is injected.

I have actually had exactly the same problem on...

Can any one tell where the flasher unit is located on this model,all the indicators are working but there is no clicking as they flash on and off

Thanks

Alanty

i have a metalic knocking noise from the front end when going over bumps in the road,i have checked the exhaust heat shield and suspension but all seems ok any one got any ideas

Hi there hoping someone can help.
I have a Peugeot 508 sw 2012 2.0
For the last few months I’ve been having problems with the electric handbrake.
Long story but essentially the original handbrake did not release one day (not long after a clutch change unsure of this has anything to do with it). Was told needed a new handbrake. I went to Peugeot...

Good morning all,I don't know if it's me or not but my car (Peugeot 207) is acting a little strange,for example when I start to drive in D mode the transmission seems to go through the gears really fast going from second to forth with no revs this happens when engine is cold when it does this the car seems to struggle to pick up speed can anyone...

Today i have finished part of project on car, where i changed oil in automatic gearbox, all went well, but when i went to check oil in car and then to change oilfilter and oil, i first found striped bolt on botom of oil pan....will manage that when i buy tomorow new bolt, and second thing-Why i opened this topic, is that i found some air preasure...

Could someone confirm that this is the correct part please?

I've got an airplane in the rear right corner......

Thanks

Going to replace the trusty C5 X7 with something smaller as 99% of the time it's only me in the car. Still doing a decent amount of motorway miles so looking for something with decent MPG and low maintenance costs. Won't be keeping for more than a couple of years. Would like to stay with the French for the distinctive looks hence the RCZ...

Hi guys, as im owner of one old 2005 peugeot 407sw 2.0 diesel, im slowly fixing broken stuf on it, but first i want to doo prior maintance, i want to change in next week or 2 oil and oil filters of engine, but doing that i want to change oil in gearbox to, my question is where could i get info what oil goes in it, its automatic 4 speed gearbox,...

Hi all

lets start with the important stuff
I am not mechanically minded so trying to learn as I go so please keep it in plain English :lol:

Peugeot 5008 (2009 - 2013) 2.0 HDi (Manual)

Back Story.....

Got the gar about a year ago after a few months started noticing some white smoke when cold starting when it was in the garage for brakes...

Good evening im a newbie so please be gentle....

I have updated the firmware on my Smeg unit and since then i have lost the car symbol when reversing, the bars appear and are as good as they ever were.

I have diagbox and have previously programmed new keys so I can find my way around it once I know where to look I am more than happy to make the...

the following numbers appear on my 3008 Hybrid4 Controlled Air intake Module.
Can anyone shed any further light on it and find it in any parts list?
T84
96 726 968 80
>PP-GF30/SEBS <
RA-GI

Hi.I need to replace BSM fuse box on this car,because it has some elctrical issue towards vacuum solenoid.I cant find here used one L06-00,so im interested does it needs to be exactly L06-00 or I can buy some other number?My car vin is VF3**************[VIN obfuscated, can be read by forum staff].Thank you

I have a problem with my Peugeot 5008 1.6hdi. It's a 2013 model with a DV6 engine. Well looked after and regularly serviced.

It developed a problem whereby it would turn over but not start or would sometimes start after manual priming or sometimes if it was left for a few minutes, no rhyme or reason.

It had a small, unrelated oil leak so I...