French Car Forum

I have v7.83 (and earlier version) on disk as part of the kit from ALiExpress Fully C chip.

When i tried yesterday to connect, it connected but could not contact the ECU ? otehr options weer avaiable

So question is what version do i need to see the ECU on a 2015 (65 plate) C4 hatchback

Thanks

Hi.

Was driving up motorway yesterday at a steady 70mph and the car suddenly dropped into limp mode.
After approx 1 minute (if even) the car returned to full power and journey onwards was uneventful.

I've just taken the lexia to the car to see what happened and I'm guessing that it is the fuel pump. But as there are a lot of gubbins in the fuel...

hello, did anyone get Lexia running on a WIN10 computer?

a seller I converted with claims it will run as is on a WIN10 computer

thanks in advance..

Hi all,

I've just purchased a 15 plate Peugeot Expert Tepee and am looking to buy some diagnostic kit for it, however, on Aliexpress I see two versions - the older multi cable grey box or the new lime green single cable box, which would you recommend? Below are the titles from each product on Ali, I haven't put links as I'm not sure if that is...

I've not having much joy trying to find Diagbox locally through the Peugeot Google map of owners.. can anyone give me a lead for someone still in the area? It's for a 2006 M59 DV6ATED4 - I want to turn the seatbelt buzzer off! thanks J.

Where is the height adjustment setting in the suspension ecu?

My ecu is suspension ecotec

Hello All,

My (until very recently) very reliable hdi 110 Xantia will not start. Engine cranks, fuel pump whirrs (it is a new one) but there is no communication with the cph. The summarised back story is: the Xantia has not been running well recently, and I was just short of replacing the EGR. To test the EGR theory I connected the vac pump to...

Hello,
Got an error message P FILTER ADD LOW . If I've understood correctly, i need to refill DPF fluid, or to change a pouch and reset the computer.. How can I find which fluid (or pouch) to use? I'm struggling to find Peugeot 207, 2009, 1.6 diesel part catalogue..

Regards, Agne

Hi im trying to figure out whats the highest version of diagbox i can use on my version b VCI.
Diagbox.GIF

Im using it on a c6 2.7td 2007 so id like to know which version of diagbox would be best for that, i managed to install version 7.02. Some ecus doesnt show up.
Can the VCI be bricked if its loaded with too high firmware from the diagbox...

Hello all, I am trying to sort out diagbox 7.83 to work with my c4 gp but it will not read ecus correctly, will read bsi ,engine ,gearbox and drivers door module but only as ecu not recognised but does have a yellow triangle indicating faults, all other ecus are showing as no dialogue. I use a msi laptop with Windows 7 32 bit installed as a stand...

Hi
What does 'diesel output delivered by the pump reference value' mean?

Is that what the high pressure sensor is reading?

Many thanks,
Rob

The V6 put an airbag light on so I got 30 pin lead off eBay to see if my mot testers machine would read it. It cleared the code but nothing else. I decided to invest in a lexia off eBay from tools4cars, who seemed to have good reviews. Definitely not the cheapest. Not working properly on a w10 machine ( virtual machine keeps erroring and shutting...

Can anyone help. My 2007 Mégane 2 hatch recently shows warning sign saying Battery Low. And once that warning shows, it looses some power and dims the lights. I went to Renault agency and they adviced me to check lights terminals of they are not loose. I ensured that they are not, but the sign still shows. Please help me out guys.

Hi , little help or advice needed , i owned the old er 508 and diagbox ran global test fine , ive now got the new 508 mk11 , so ive uploaded the new software 9.91 for global test only to my windows 10 as recommended, everything seems fine except when i run a global test on my car it says on all tests (no dialogue) , so my question is why , im...

Taking the 'diagnostic' term reasonably broadly here (i.e not just electronics), hope that's OK, I wonder if anyone has experience/recommendations for brake fluid testers?

I see you can now buy electronic testers for 30 quid that will tell you how much water is in your fluid. Are they any good? No doubt some models are much better quality than...

Renault Scenic Grand MKIII 2010

Hi folks

Having a painful time with 2010 MkIII Scenic Grand, which I bought in Nov 2018.

In December the check parking brake warning light suddenly came on. The parking brake worked fine, tested on steep hill, so hadn't a clue what the issue was (car newb). I was advised to check for water in the storage bins...

I have an idea that this box as fitted to my C4GP might benefit from a recalibration procedure using lexia 3.
It looks like it might take a little time to go through the whole process, well for the first time- given that I would choose to pick my way carefully.
My worry is whether the economy mode would kick in

Hi, just bought a upgraded version of Lexia 3/ Diagbox, but the software wont connect as its stating that my interface needs to upgrade from Rev B to Rev C.

I know that the chip in the interface can be flashed with the newer coding. Anybody know of a location to obtain the coding?

Thanks

Well bit upset as wasted £12 on Lexia update from Ali Express. Instead of a disc like I’d hoped for just ended up with emailed link from french supplier. Tried to download but 3/4 way through asked for more money to finish download which wasn’t happening. Previous version from 2018 bought for my 2013 308SW doesn't have my 2017 2008 on it. Does...

Hi

I got some cuts out when the car is in idle and i think i have a problem with 1 or more injectors? I have made a video when the car is in idle and at 1500rpm. and when all numbers is the same on the video its rev 2000rpm.

I cant understand the flowing hogn and low numbers but i do think there is some problem with 1 or more injector or the HP...

So I decided to update to Diagbox from my venerable Lexia software that I have been using successfully for several years.
I initially installed Diagbox 7.02 on a fairly ancient HP Pavilion laptop operating on XP Pro SP3. Although installation and activation were ultimately ok, the spec of the HP made Diagbox very slow to load and incredibly slow...

The fuel injector in my car recently shorted and I got it replaced at a local garage. However, they said there was an issue with the calibration process but that it might calibrate while driving it. However, it has failed to do that, so I'd like to see what's going on.

I have ordered a lexia 3 from china but it won't arrive for several weeks, so...

I reseted the lateral airbag module , and , now is flashing 4 Times and remains on ? Whats that ? demonstration.rar

Hey guys, i have some crash data on my Peugeot Expert 2018 and the garage i went to couldn't resolve them, if i buy lexia 3 kit would I be able to get somewhere with Diagbox, ive attached some images of the diagnostic report.

2E6E99DC-8C9E-497F-8D23-C3A15F545EF2.jpeg

B7374E22-4ED8-4B7B-BB87-B28257D975E8.jpeg

hello my friends,
as you know, from servicebox ( we can look up error codes' diagnosis section but it's a paid service,
that's why i installed windows xp on virtual environment, opened docbackup and sedre but couldn't see diagnosis section,
is it unavailable?

Hi All,
New to the forum! :) Some great information here.
Looking to get some assistance. I had a towbar and dedicated electrics fitted (ECS wiring loom), but in order for this to work. I need to have this the trailer/towbar function activated to detect the the new loom.

Not sure if there is a friendly local who can help do this or happy to...

Thanks for reading 📖

Where do I start lol so had the abs esp fault come up scanned on Autel Scanner says brake switch fault

So changed out the switch with the adapted harness as well and made no difference light still comes on and dredded gongs 😮

Can’t work this out
Anyone else had this problem

Hi does anybody have info on this and is it any good. PSA-COM Bluetooth Pro Diagnostic Tool for Peugeot/Citroen for sale here in South Africa. Will it have the same functions as the diagbox and lexia software

Peugeot 207, 1.6, NFU. Good ECU and throttle body.
The major issue is that the throttle plate does not move. It does not even appear to get a signal to move, but it does however on a Citroën ECU, a bit of information below that I've gone through.

I have had it wired in two ways, one produces one throttle programming fault, P1153, while having it...

Hello everyone,

The recent cold snap finished off the battery in my facelift C5 (2007 hdi Exclusive) and I was rather slow in getting a replacement. Now with the new battery on the car I have a number of 'interesting' fault codes which are reluctant to clear properly, plus the added feature of the headlights and wipers springing into action when...

I think I might just chuck my non-functioning vci in the bin, so which one should I go for to replace it?

Hi everyone,
I have a 2011 Citroen C4 1.6 VTI auto, and I'm in trouble with my car, there is a lack of power both on petrol and LPG, it feels more when going uphill, slowing down too much, straight road acceleration is not satisfactory, fuel consumption is also seems high, i took my car to the authorized technical service, and gives the following...

Has anyone recently had any problems getting Lexia to connect and run a diagnostic on their car?
A slight suspicion that if allowed to connect to the internet (i.e to PSA), some functioning could be put on hold, maybe for commercial reasons.
I had thought that advice was not to allow web connection or updates, on ex-workshop platforms...?

Hello. At the beginning I would like to point out that I am from Poland so sorry for grammatic. I have quite a problem with Peugeot 206, 1.4 petrol, 2002.

While driving and when stationary (with the engine running), the electrician in the car goes out for a moment:

> turns the tachometer and speedometer,
> the lights go out (not always),
> the...

Hello out there,
Does anyone have any idea where I should start looking for faults;
MAF ?
O2 sensor ?

Dunno where to start !

I have a leak in my power steering. My car is a Citroen Picasso 54 registration
Is it worth getting it repaired and any idea of the cost? Also are the leak stop repair solutions you can buy worth using?

Hi all, just recieved a PM about Lexia/DB usage & wondering if my kit will be able to do what's needed. The message reads-

Good evening, not sure if you can help I've refilled my dpf fluid tank Dispatch van 2013 and need somebody to help with resetting the ecu counter. Have tried with a snap on solus handset but it wouldnt communicate so Im...

Just wanted to add a feedback. A year ago I got Diagbox diagnostic kit . Quite happy with that, but a bit surprised it was somewhat sluggish and slow. It demanded a 32bit OS, according to the seller.

I recently bought a 2020 version of the software , and I'm pleased to say that layout is better, its alot more responsive, does not crash, and since...

Good afternoon all :-)

Just a quick question.

I have C4 Pic 2014 Exclusive (B87) and I'm going to give it a big birthday service soon.
I'm a capable mechanic type person, but I'm just wondering if there is a specific process in replacing the Coolant/Anti freeze.

Any help would be most appreciated

Cheers
Zane

Hi Guys

Can anyone supply me with details as to how to obtain Diagbox cleaner ?

Just posted this in the Pug area but thought it may be worth linking the question to the diag forum too.

Thanks for any help, Dan.

This version won't work in a standalone installation. It needs VMware and a laptop that has virtualisation technology and also enabled in the BIOS. If you want a dedicated install, you will need to buy that specific version / licence.

A friend of mine is looking to purchase a copy of Diagbox and the necessary cabling that goes with it.

Who is a supplier of the known good ones these days? There's so many on eBay at such a range of prices I'm unsure what to look for!

David.

Vin No. is VF7**************[VIN obfuscated, can be read by forum staff]************** .
To give some background, the engine light came on and the car goes to limp mode. A garage spent alot of time (£1300) getting nowhere and replacing stuff. I then replaced the MAF, fixed a connection issue with the air manifold and changed, for the second time a new Fuel Rail pressure sensor as i keep getting P0193...

Hi all, Hope everyone is well. It has been a while since I posted! I own a 2002 C5 and a 2004 Berlingo and just bought myself a Lexia 3 diagnostics kit from Easy Diagnostics.

Before it arrives, I thought I’d ask if a guide to using Lexia exists. I’m very much a newbie at this but quite computer savvy, so I’m hoping to learn quickly and get to...

i had a new torbo fitted back around 6 months now and as i am going up hill the car seems to lack power or the turbo is taking time to kick in
it sounds like it is slow picking up any answers on the ,is there some thing i can do myself or will it need a garage to test the turbo

just wondered if anyone might have any insight on a wierd issue I'm having with my xantia HDI 110.

auxiliary belt came off due to broken tensioner pulley. That was repaired and car was driving perfectly for a couple days. Then was driving on and off throughout the day, went out in the evening and the car wouldn't start. RAC guy says codes were...

Hi ,I am having trouble with my 59 plate C5 x7 ,in the morning I turns over for quite a while before it fire's up .it will turn over for about 10 to 20 seconds , sometimes it catches straight away,then stops ,but then starts when I turn the key again.its is all most like the fuel is draining back to the tank ,and needs to turn over for a while to...

Hello There,
I had a problem with my Lexia install and now wish to use the Diagbox uninstall cleaner v1.0a but it seems to be taking forever. Does anyone know roughly what sort of time this takes please?
Thanks
Darren

hi all i am new to this fourm and to diagbox. i have installed diagbox and updates up to v7.76 i am trying to run the update (8.18) v7.76 to v7.82 but its asking for a password the readme doc with the files says the password is Very Simple! but when i enter it its not accepted i have tried varations of the password.

anyone got any ideas or...