French Car Forum

Morning, I am new to this forum and would appreciate any assistance:

I have a Peugeot boxer van (2000). From what I can gather online the engine is 2.5 TD PSA THX (107 PS (79 kW; 106 hp) @ 4,000 rpm) - this engine appears to have been available between 1998 -1999, and then again in 2000. From what I can understand the engine code is DJ5TED -...

Hello everyone,

My car is a 406 with 1.8 16V LFY engine (Bosch MP7.3)

When I let off the throttle, the car jerks forward and this is somehow irritating for me and makes smooth driving through traffic impossible.

I fiddled with TPS and adjusted it at different voltages which decreased the effect but didn't eliminate it completely.

My IACV is...

Hello all.
Just wandering if anyone has had a lot to do with these vans? I've got a 2.5d that's on its last legs but I was going to give it a new lease of life with a 1.9TD engine.
Trouble is I don't know what bits are compatable between the engines - would I need mounts or the gearbox or everything?
I've never done much with the 2.5 but I've...

Hey guys just wondering what after market stuff you have added to your cars let me know

Can anyone tell me if the top engine mounts on a 307 are interchangeable? petrol diesel etc?

I don't have a spare key for my 307. I don't have the little card with the code either and I'd like a flip key into the bargain. Are those ebay keys any use? Is there any way I can get the code? Thanks

hi all, Swimbo's 206 packed up at lunch.. I just went to rescue it/her lol

the symptoms were a non starter on the key, complete with clock resetting to french days, and so on.. I dont know if the engine turned over or just clicked at the time.

I went to it, stricken near the Hop Farm for those that are local, and measured battery voltage, 12.4 -...

Hi all, does anyone have a small left hooker that they no longer love? I'm after anything, 106,206,306,ax, SAXO, zx,preferably uk registered, many thanks

Hi. Today I was goofing around in my car. I removed the ashtray from its place and I noticed a little diode. I tried everything to light it up - turning on ignition, pushing the lighter button, etc. Anyone knows what this diode is for? I'm just curious.

One of my estates has suddenly come over all weak. Very little throttle response until you get to around 2600 rpm then it takes off. Tried MAF as that's what it felt like but no improvement, also found the throttle cable slack, fixed that still no better. No smoke, tried an Italian tune up that didn't help either.

Any suggestions?

Thanks. Peter.

Hi all,

I have a 2007 Partner with a 9HX 1.6 HDi engine, 148000 km (92k miles). It has a tendency to idle slightly uneven when cold, but apart from that seems to be pretty solid. I bought it 6 months ago and at that point it needed a new EGR valve and glow plugs, which I have done. Also it developed a leak on one injector, so I pulled that one to...

chaps, I keep seeing a 607 for sale on a street.. it attracted a PCN today.. it's £600 and 2002.. a 2.2Hdi

I dont know what to make of them really.. it's a climb down from the X7, in every respect I would think.. it's not any more practical.. is there anything good or exceptional about them? or are they just a large barge with average economy...

Looking at either a 307 or 308 hdi

There seems to be a 1.6 and 2.0 in different bhps. Which have fap and do all have duel mass flywheel?

Seen a 2.0lt 90bhp which from Google has no duel mass or dpf and a 1.6lt 110bhp but not sure what it has, engine code DV6TED4(9HZ).

Thanks.

The lights on my clock display seemed to be getting duller so I took it out and changed all the bulbs now none of them works! Is there a fix or would using these do the job? . I also have power to my fog lights at the plug on the back of the light but no power to the bulbs on either side, how can this be possible?

Hi all, I'm interested in finding out if a spare set of injectors i have would fit in my van.
Not that i have a problem at the moment, but your never know,
I have a 2007 Peugeot Expert 2.0L RHK 110 hp, I think,
Siemens Injector number 9659337980
The other set is out of a 407 RHR 120hp engine Siemens Injector 9647247280.

I've tried local parts...

Was wondering if anyone here has a good knowledge of Peugeot keypad immobilisor systems fitted between 1992 - 1996, especially whether they can be removed completely (as opposed to disconnected).
 
I've noticed on a few occasions, which have became more frequent, my 405 petrol automatic wouldn't start unless you locked it with the plip, then...

Hello and good day, i have recently purchased a 61 plate Expert Tepee L2 WAV with low miles. I want to fit a tow bar, but the tow bar companies say it cannot be done. I have tried to get in touch with the original conversion company Constables . but it looks like they are no longer trading.
Does anyone have similar experience. / solutions

My peugeot 306 hdi coming up with a fault code P0380

Glow plug / Heater
Circuit A

So is this the glow plugs need changing or the heater relay for the glow plugs?

Does this show which one is circuit A?

The last time it was cold the car was misfiring a bit on startup harder to start also a bit of smoke then clears up. So I had an idea this was a...

I'm struggling to find this part brake servo booster to fit my car. I've had Peugeot say there 3 different types and had motor factors and online problems. The car sitting in the garage surely somebody must know where or has one.

The details

ATE
96 282 755 80
03.7752-0231.4

The model car 306 hdi with abs and bendix brakes

I even tried this one...

Hi,
Hope you can help me understand how to understand injector flow correction reading from PP2000.

the car is a peugeot 307 1.6hdi 110

reading idle as follow:

injec1: 1.63mg
injec2: -5.53mg
injec3: 0.03mg
injec4: 0.17mg

I have concern for number 1 and surely 2.

hi all recently my airbag warning light has appered so i plugged in my diagnostic tool and im getting back this error shown in the picture can anyone help me solve this as my mot is due next week. thanks

Lilpug is a little poorly. She is running slightly erractly, missing at times and backfiring. I have fitted new plugs, plus leads, air filter, fuel filter, oil and oil filter. It feels like the timing is out. However it has Bosch single point injection, electronic ignition and an ecu. So therfore I can't do anything about the timing. Anyone any...

The vans have been swapped round today.

I've found an empty 1L bottle of 10w40 A3/B4 part synthetic oil in the cab of the new one.
The turbo pipe is leaking oil which explains why.

Problem is that the Van is Euro5 with a particle filter.
It's recommended oil is 5w30 C3 low SAPS Synthetic.

The oil on the dipstick looks watery and very black....

The ignition lock on my 2000 Peugeot 306 has finally worn out ( lock still engages but haven't been able to remove the key for over two months now!)

Anyway, I've figured out how to remove it (quite easy actually) but all the replacements I can find which claim to be compatible with my car have 6 wires on 3 connectors but mine only has 4 wires on...

Hello.!
I must say that the automatic box works excellent, does not jerk, it does not go into protected mode.
After changing the heat exchanger, I went for a spin to try the car.
Now I have an error which is as follows:
PERMANENT DEFECT. CONVERTER BRIDGE. COHERENCE.
Anyone know what you mean?
regards

My daughters 307 blower motor has stopped I have changed the resistor in the blower cowling, The wiring and the plug looks OK and it still does not work
Im going to take the motor out and check it . Where does the wiring from the resistor go to. Is it easy to get at if i strip everything out in case I have to solder a new resistor loom on
I have...

Hello,
I´m rebuilding a 1.9 XUD9 Diesel and need some parts, anyone knows where can i get it?
I´m looking for the usual rebuild parts, pistons, rings, but i need specifically the turbulence chamber(Chambres de Turbulence). I´m living on South America, but i´m in Europe every 6 months, so it´s easy to me get some parts from Europe. Thanks for any...

Hi,

I have just changed the transmission in my Peugeot 407 1.6 sw, deisel, put it all back together.

Turned over first time , done 15 miles in it and whilst driving down a dual carriage way , the engine went off whilst fully accelerating and I rolled onto the hard shoulder.

I then tried to crank , nothing !!! Not even a relay click.

Spliced...

Wasn't someone looking for one of these the other day/

Hi

I am looking to download a workshop manual for my 4007.

Can anyone point me in the correct direction? Cheaper the better

Thanks

I've noticed that my 206 has problems with power steering. Right now it works like this: when I drive after a break (eg. in the morning), it's bearable. After only 10-15 minutes it just stops working. I know there can be a million and one reasons so I'm just asking for possible suspects. I refilled the fluid. When I bought it, the previous owner...

Done!

Another issue. I put the gear oil in the 307 and drove it a few yards and there's still a bearing rumble it's coming from the offside rear wheel. The bearing seems to be part of the disc, the Haynes manual details how to remove a rear brake disc but not this type. I'm pretty sure I can get the hub/disc off but my question is.... How does the ABS...

I have nearly completed my 405 XU10J4RS conversion (I'll maybe post a project thread) but I'm having a bit of trouble with the clutch and/or gearbox. Something makes a horrendous noise with the clutch engaged in neutral:

The original box and clutch on the 1.6 was a push type setup. I've rebuilt the 1.6 box with shafts and diff from a Xsara VTS...

I finally bought the Haynes manual for the 307 timing belt and reading through it the book says 75w80 GL5 gear oil. Doesn't say if synthetic semi synthetic or mineral. I had already bought a gallon of gear oil as recommended by my local motor factor it's 75W90 GL5 semi synthetic would it be ok? I looked at the misterauto website and they show 2...

Turbo not engaging at any point and it's become a nightmare up hills
Actuator not moving was first sign so put a silicone hose on it and did a basic test to see if it moved and held air and it held so realised that's ok. Pipe to the actuator is not getting any air going through it so i thought is the electrovalve dead on it. Replaced and blew...

Quick question for anyone in the know, what's the difference between standard 206 wishbones & GTi/CC wishbones? Is the balljoint a different size or is it the length of the arm/track width? We're due for new wishbones on the front of our (mildly modified) 1.4 HDi and was pondering the difference between the two.

If the GTi/CC wishbones have the...

Hoping for about of advice as I'm sick of local garages ripping me off!
Recently had my 2009 reg 207 Verve mot'd and an advisory was given for a radiator/coolant leak. There does appear to be a leak which I can't find but at the same time, even with the recent hot weather, the temperature gauge is staying low and only seems to rise after the car...

anyone got any thoughts on Febi / First Line / other make suspension bushes?

Am a little miffed that the rear bush on one of my front wishbones has play in it, having only replaced it in the last 2years (25,000miles). The front & rear bushes on both wishbones were done at much the same time: a time costly errror that was... not doing the lot all...

Please could one of you nice chaps with access to Peugeot parts info please aid me by getting a part number and price for the part in the pic?

It's part of the engine breather system and attaches to the rear cam cover and connects to the plenum in the centre and the air intake on the right as you look at the pic.

It's an 07 plate 207 1.4 petrol...

Hi
Does anyone know the correct grade oil for a Peugeot 107 (petrol, 2008 reg) manual gearbox ?
Thanks

Has anyone managed to rebuild one of these at home - including the shafts ?

We have done Xsara axles but we use our home-made press.

The 206 axle is reverse of the Citroen - looks like you need a hydraulic puller to get the shafts out - unless you can push one shaft into the tube and then push 2 out together ?

Cripes - the price of the 205 td has really climbed a lot here in France in the last 12 months.

We wanted to but one and put a 1.9td into it .

Could get one last year for 500-600 euros. Looking at 1500euros plus now.....

We have been thinking that a 3 door TD is a nice economical alternative to a GTi. Not the same power admittedly , but can be...

I can't remove one injector to change a seal and I don't have a puller, any suggestions on how to remove it? Peugeot 307 with a 1.4 HDi engine, thanks

I have a 4007 hdi with the engine light on. Have read the codes (snap on souls) and have the following faults.

Not to concerned about the egr code as I blanked it off.

Advice appreciated on the other codes

IMG_6933.JPG

Thanks

Lloyd

Well, the 1.4 engine has a reputation for leaking oil from the head gasket as we know. Mine has already had a head gasket replacement some time ago, but on 85k miles, was leaking oil again. I hadn't really inspected it, as I presumed it was the head gasket, and I would just keep putting oil in it rather than shelling out to get it fixed. Anyway,...

The Boxxer is rapidly going through os headlamp bulbs. I suspected a poor earth so I removed the entire headlamp to check. It doesn't appear to use body/chassis earth at all. Theres only one cable iI can't trace as I'd have to take the bumper off but i don't believe it is an Earth. Connections are both clean and secure.

Any ideas or should I just...

I've changed the discs, pads, calipers, hand brake cable managed to get everything working fine on 306 hdi.

Now there a hissing sound coming from the brake pedal area. You can drive and it will start hissing but when you press the pedal a bit it goes then either comes back or goes random. The pedal goes a bit spungy I have noticed at the back of...

Well, it's as per the title really. Comparing the 308 with our previous Xsara Estate it really doesn't match up. the ground clearance at the front (and middle) is terrible. We have to take it really easy over speed bumps and there's a hump in the road near our French place that we have approach at just the right angle otherwise we end up scrawping...

So where the cheapest place to buy a new brake booster servo for a 306 hdi year 2000.

It has abs brakes with bendix brakes.