French Car Forum

Hi, I am trying to REMOVE a wheel bearing with ABS RING, on my 04 plate 206 - I tried to PRESS this out using the old fashioned BOLT and WASHER extractor method, to no avail.
Is it POSSIBLE to REMOVE both the old bearing + ABS RING at the same time ? (to-gether).
The BEARING has a 52mm Outside DIAMETER and the ABS RING has an internal DIAMETER of...

Hello, may I ask for the RT6 head unit pinout for this VIN: VF3**************[VIN obfuscated, can be read by forum staff]? I found out that they are different in each version and I want to be sure.

Hello. Two weeks ago I had a problem with one injector (lean mixture in the cylinder). As it turned out, it was a problem with the piezo element closing to the injector housing. Since I had already done this and I have experience in this, I removed all the injectors myself and took them to the service for inspection and repair. I installed the...

Hello to you all!

I am new on this forum and I am hoping that I could find some help in order to solve the problem which I encountered on my Peugeot 508 RXH, 2017, BlueHdi 180hp.
I've read all the forums I could reach in searching for a solution, but so far no luck.

For almost two months I’ve been trying to figure out what happened with my...

Hi all. I'm new here hoping somebody can help me out. We did a battery change on our 3008 2012 diesel with auto gear change (manual box) without following the correct procedure
It wouldn't start, came up with engine fault, handbrake wouldnt go on and it says it's stuck in m-
It took me a while to get some advice. First I thought bsi and was all...

Hi everyone!

I desperately looking for any advice to find the problem with my car, because i'm out of ideas.

The car is a Peugeot 407 2.2HDi 170 which ran fine until one morning it simply doesn't start.
Diagbox indicated an intermittent P0341 camshaft sensor - signal absent error, so I thought an easy fix. I bought an ERA aftermarket sensor,...

Hi,
Firstly sorry if this is an obvious one, and I’m just being slow or not looking in the right places,
I’m based in Glasgow, currently about to get my first works van, a Peugeot partner and it doesn’t come with Apple car play, it is a 2020 plate and it has the infotainment touch screen.

I’ve seen online it’s not available to buy the upgrade...

Hi got peugeot boxer 3 with air bag fault,3 codes set
1 u0019 can fault
2 u 1703 comms with instrument panel
3 Bo100 ecu internal fault
No 3 I think is common fault ( ECU REPAIR) Let me know if you think different
What I would like if possible, a wiring diagram for air bag system please to help me check out unit
VIN No=VF3**************[VIN obfuscated, can be read by forum staff]
Thanks...

Help request – Timing timing / VVT pulley preload Peugeot 207 THP 150 (EP6DT)

Hello everyone,

I am in the process of replacing the timing chain on my Peugeot 207 1.6 THP 150hp (EP6DT), engine identical to the N14 Mini.

I used the shimming tools to lock the camshafts and crankshaft. Everything seems well aligned mechanically. Before the change,...

Hello,

I have 2021 Peugeot 508 SW Mk2 2.0 blue hdi VIN vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff].

I'm replacing the front and rear discs and pads and to do this you need to remove the disc caliper from the axle. Can anyone provide the tightening torque settings for the bolts which hold the calipers to the front and rear axles? Also the bolts for the pad retaining frame...

Hi all,

so suddenly my 508 (1.6 bluehdi 120hp) started making very loud knocking noise, which I assumed to be engine knock at first. The noise mostly happened during idling, but the car was really loud in general. Upon investigation, I narrowed it down to a loose flexplate. I assumed I'd only need to retighten and glue these bolts, but couldn't...

My Peugeot 806 suddenly died when driving and wont start.
I have tired/checked the following:
- Gasoline pump wont start when turning ignition on
- When cranking the starter motor will crank but there is no spark
- Replaced double relay, still the same
- Tried to connect 12V directly to the fuel pump (through double relay plug), the pump starts...

Hello.

I have a sunrooof drain leak into the cabin on my 309 which has the factory sliding sunroof with the vacuum seal.
On peeling the headlining back, I can see that the front corner drain tubes from the sunroof tray are quite corroded and weeping slightly.

It copes with normal rain ok, but not so good with washing the car when large volumes...

hi guys,
I'm hoping someone can help, I'm looking for the part no for a clutch kit for my peugeot expert, Its a 2005 2.0 hdi dw10ted4 with a solid flywheel, & ml5c gearbox been looking but all i can find are kits for dual mass flywheels or conversion kits, problem I'm having is the releaser keeps pulling out of the pressure plate, clutch was...

Is there an easy way to identify if my 2008 307SW Hdi has Bosch or Lucas/TRW front brake calipers?

Not sure yet if I need new calipers or just a service kit for the glide pins, front offside brake binds and only the fixed pad shows signs of excessive wear.

With Thanks

Alternator pulley disintegrated and was found lying on the sump guard, leaving just its innards still attached to the alternator 😢.

I have the M10 splined bit and associated nut required to remove the pulley and these do just fit with the alternator in situ, but I was just wondering before I invest in any more tools has anybody successfully...

I've posted elsewhere about rough running on my wife's 207cc, 1.6l petrol, 2008.
I am now getting a consistent Exhaust Camshaft Dephaser too far advanced. I've changed all the sensors, check static timing and I am now changing out the Dephaser sprockets. Feeling my way with this, not a job I've done before. Got the Ex. Dephaser off and it seemed...

hello everyone.
I have a 508 RXH hybrid4 that just won't stay running. If I clear all the code with diagbox(9.85) and I remove the traction battery cable from the hybrid battery itselfe ,the car starts for a few second then dies and a lot of errors pop up.After the small start I cannot start the car again if I don't cleare all the code again....

Hi, looking for some advice, I have a peugot 207cc 2010 that has an engine warning light and some error codes that I'm struggling to troubleshoot.

P2178 - mixture adjustment
P1336 - combustion misfiring
P1337 - misfire on cylinder 2
P1338 - misfire on cylinder 3

The car is juddering, pulling back and losing power. I replaced all sparks and...

Hello world, may I have a couple of minutes of your attention...

I bought an old relic: 407 2.0HDI 290000km with some problems registered 6months for 500€

The car had a dead turbine, but after I fixed some vaccum leaks it woke up, and started dying at higher RPM, so, after I cleaned the sensors on the intake side, and confirmed it got new turbo...

Hi I got peugeot boxer 2018 HDI 130 Ithink engine type DW10FUD get lot of conflict between 0w30 and 5w30 most oil sites state 5w30 on oil ref page on here it seems to be 0w30 psa 2312 vin code VF3**************[VIN obfuscated, can be read by forum staff]

Tim

Hi
You could always use the nylon string trick through the spark plug hole.

Hi Everyone, new to the forum and didn't really find this topic after seeing quite a lot posts in the forum.

I have a Peugeot 308 SW T9 1.6 BlueHDI 2015 model (Allure model). Recent trip to Morocco triggered an idea of driving my own car from UK to Africa. Knowing the awful ground clearance and load capacity, wondering what could be improvement...

Hi. My friend has a 2001 peugeot 206cc 1.6 petrol VIN: VF3**************[VIN obfuscated, can be read by forum staff], number in door jam 889288.

Theres a bunch of electrical problems with it:

Periodically it wont start, but then if you wait a few minutes it will. The engine just cranks but doesnt start.

There is no power to pin 16 (constant power) in the obd2 port in any positions on...

Hello everyone.

I use RT4 in my 207 vehicle.

Can I install an RT6 without changing cables or anything?

I apologize for the spelling errors.

Hoping somebody on here can help/ provide more details on this...

i was hoping to sell my car but when the dealer plugged his OBD reader in it was throwing up a fault - U1208 - communication on the CAN with the Engine Management ECU - Permanent

he took the car out for a drive and everything was fine, no issues with the car and everything in full...

Peugeot308 t9 P01434 P01435 codes came up on dash also countdown for ad blue i did not realise that both systems are fixed ie two tanks a elloys tank and a ad blue .I thought it was a adblue tank fault removed tank cleaned inspected oms test pump but ok oms test on wire voltage ok i didn't understand what was going on till I realised that I had...

Hi all,

I will do the introduction bit after I post this, while it’s all in my head!

A few weeks ago I bought a 2008 Peugeot Partner Tepee, and it’s been an utter clusterbomb of shenanigans and such like. Wiper failed the day after I bought it resulting in a replacement mechanism. Then the turbo quit, resulting in a whole heap of work from...

Hi, does anyone know the tightening torque for the injectors for this engine? Thank you

Hi all, I'm new to the forum and am looking for a bit of guidance.

I am considering buying a Peugeot Partner Tepee as my daily and, to then use occasionally as a micro camper, using 'a put in pull out' Boot Jump. I have scoured the market for vehicles in the £4-5,000 price range, with mileages varying from 65,000 to 130,000, in the year frame...

Hello,

I searched the forum but could not find any information on this. I need to change F + R discs and pads on my 2021 MK2 508 SW 2.0 blue Hdi. Does anyone know whether the caliper pistons are screw in or push in? I have the tool but do not want to damage the pistons unless I know whether they are clockwise/anti-clockwise or simple push in. Any...

Hi everyone. I’ve run into a problem: the car doesn’t start on the first try, but it always starts on the second. This happens at different times but not consistently. Has anyone had this issue? The fuel pressure has been checked, the spark plugs and coils have been replaced, the timing belt has been changed, and the fuel filter as well. I’m...

Hi

I have a 11 reg Peugeot 207 1.4 Diesel which has 98000 miles on the clock. Recently after filling up, the 'Fuel additive level too low' error appeared.
My question is - Is this something only Peugeot garages can change and reset the ECU or do you know if any other garages are able to do it?
My local Peugeot garage has quoted £250-£300 to...

Hi my van is pulling to left on acceleration
And also juddering , the steering wheel is jumping out my hand , it can drive for 40 miles perfect then starts pulling to left , any ideas please

Hi
Seriously need help,
I have a Citroen Xm with a Peugeot 2.0hdi RHR (siemens 803) engine from a 407.
The problem is that I can't start the engine before I've deleted the fault codes.
The fault code is P1169, something with the voltage to the injectors if I understand correctly. If I delete the code the car starts immediately and runs normally...

My 2007 Peugeot 207 has a clunk / knocking noise that seems to be most prevalent when the car goes through a pot hole or over a large bump in the road. Trying to get everything sorted prior to MOT next week. My current list of things to take a look at to see if they are the cause of the problem are:

Broken spring
Shock absorber
Worn bushes...

Hello peeps been searching around for an answer to this but havent had much luck so thought id ask it myself.

the rear mounting bushes on my 207 hdi GT have worn and as a result are knocking anytime you go over a bump.

i have the new bushes to replace and a pair of bolts that hold them into place as looking at my current rusty ones i think im...

Peugeot 308 sw 2009 ew10a 2.0 engine.

I recently upgraded from RD4 to RD45, got a new display also, i finally have bluetooth music and handsfree calls. But i cant seem to get TA (Traffic announcements to work). Using diagbox 7.40, i checked the region which was China, the only i could change to was:
China
Japan
South America
USA
Other Contries...

Hello everyone.

I have a 2011 Peugeot 508 with the 1.6 e-HDI engine.
The car starts and drives and the battery voltage is near 14V, but the diesel (resistance/glowplug) light stays on and power steering does not work.

Running a scan shows the following errors:

P0A1A - Alternator. -> Alternator communication fault
U1401 - Alternator LIN network...

hiya all, I just want some general advice on getting a 1.6hdi remapped

my main question is, if I have a stage 1 remap will the car use more or less fuel than stock when driven normally?

I do have other questions but lets get a general opinion of that one first, ideally from those of you who have actually had a remap on one of those engines....

Hello.

Some time ago, I bought a lightly damaged Peugeot 508 e-HDI (SW) from the year 2011.

Unfortunately, some time after the accident someone stole the engine ECU from the car.

Now I need to get the car running. What are my best options? I have a used engine ECU I got from a junkyard with matching part number. What is the best way to code...

Hi all

I have a 2008 Peugeot 207 1.4 8v with a steady drip of oil from the area where the rear crankshaft oil seal is located. I am just about to whip the gearbox and flywheel off to have a look but it would be great if any of you have any tips to share before I get started with this. I have already identified to stay clear of the PTFE...

Hi there I am new to the group,
Would anyone be able to help? I have a peugeot rcz 1.6 petrol turbo 2011
I need to know the correct timing settings, with more information could anyone help please?

Many Thanks,
Mike.

Hi to all, new member here looking for help.
I have a 4 year 207 been a good little car ,but lately im getting water in the drivers footwell after heavy rain, i've been told there are drain holes under the bonnet in the region of the windscreen that may be blocked, had agood look around but cant find them,
any help would be appreciated.
Thanks

My daughter has an Peugeot 307 1.6 petrol from 2005
With the TU5JP4, this winter it has not been very much used and last time it was droven was the 26th of December, she drove it and parked it, some days before january i decided to put a charger on the battery and left it until the 5th of january, she tried to start it but it would not start,...

Shortly after purchasing this car, I needed to replace the visual display unit that sits on the top of the dashboard. Mine was faded so badly that it couldn’t be read.

Once I had found a good replacement unit, I found that the seller also had a later model of the radio which had Bluetooth! Hands free phone calls, and streaming music were too good...

Peugeot 207 -06 1.4 KFU (ET3J4)
The brake pedal is soft and the onboard computer reports the following faults: ABS system faulty, Anti?theft system faulty, and Antipollution fault.
The ABS unit was replaced with another one from a scrapyard, but the fault did not go away. The error code is still U0121.
Does anyone have experience on where to start...

Hello all,

I need some advice on how to continue.

I bought a SH Peugeot 5008 1.5 BlueHDI with EAT8 a few days ago as my C4 EGS let me down (in very cold days).
I drove it around 500km back home in 2 different days (starting at -14 in the morning) and no issues.
Yesterday morning (-4 deg) I started and tried driving to work, but after 2 min...

0Leaving for work this morning and the car cut out a mile up the road. orange EML light, but I dont recall a beep or a message. Not even a cough when I turned the key - it wound over OK though.
Towed it home and had to try to use the starter and 1st gear to haul it onto the drive, and it coughed and fired up. Antipollution message on the display,...

Hi I have a Peugeot 3008 1.5 hdi 2019 with adblue fault last week I replaced the urea injector as it was open circuit and leaking adblue, that fault I was then able to clear and now this week I have a different fault with adblue system fault code P20EE 92 and depollution of the deNox system effectiveness fault the system pressuring ok 5 bar and...