French Car Forum

Hi!
Long story short: I had my injectors replaced. The first run after that was super good. Smooth and steady. Then they were coded with Texa. Now when cold the car loses power, there is white-grey-ish smoke (more smell that visual) and you can clearly hear the injectors. This happens up to 40-50C and then all runs ok. The injectors are audible...

Hi wonder if you could help, I have a Peugeot 3008 2L diesel hybrid 4 2013 and I have gearbox oil coming out of the breather pipe on the reduction gear, it has the correct oil Total 75w-80 and the correct amount 0.7 of a Litter after a run I get droplets of oil coming out of the breather pipe on the reduction gear, there are no faults in any...

Hello everyone.

For my Peugeot Boxer from 2008 with PUMA engine and FIAT technology ( VIN VF3**************[VIN obfuscated, can be read by forum staff] ) I would like to buy from tools4car Lexia 3 with the newest Diagbox to be able to use DiagBox for further troubleshooting. The eLEARN software that I use from Fiat is great, but is not helping me with my problem at the moment.

A BSI...

Peugeot Boxer, 2.0 HDi DW10TD. Production year 2005. Vin VF3**************[VIN obfuscated, can be read by forum staff]
Hi, any help, advice would be very much appreciated. Since last week my van developed some strange noise. I dont have any problems with starting it or any power loss, goes well as always. Doesnt matter if the engine is cold or warm, if i press or depress clutch. Noise goes...

So I have just done an engine swap and it sounds like it's down a cylinder.

Injectors 1 and 4 were remanufactured units from PFJ injectors 2 and 3 were tested and passed but it looks like number 2 might now be dead. Flow correction is constantly 15mm3

Screenshot of data. Am I right?

After battery going flat speedo now shows kph, how to change back to mph
thanks Joe

It looks like the old parts number lookup service is no longer functioning. I have been using a website called partsouq.com/ . It has well-detailed drawings and lists part codes for all the things on the drawings. Using those codes I have been able to track down almost all the parts I need.
Today I find that I can't enter the site without setting...

Hi all,
I recently did some work on driveshaft so needed to drain gearbox oil. Refilling it through breeder valve at top of the box. Long story short I took battery out for 2 days. After connecting it noticed that my folding mirrors stopped folding when locking the car. Didn’t bother me much at the time but then noticed that even when cold start...

Just a short post on my experience with Febi parts on a 2012 208 1.4d.

Two and a half years ago, when replacing the clutch, I did some 'while you're in there' jobs and purchased the following parts from Febi Bilstein.

Track rod ends x2
Lower arms X2
Drive shaft seals x2

The car has covered 20k miles since and I've just noticed one of the lower...

bonjour
j aurai besoin de trouver le lien official pour une installation d'un firmware pour mon rt6 2.86 B
je veux vendre la voiture et je ne veux pas mettre un prix énorme pour les réparations
merci pour votre aide

Hello,
I need to find the official link to install firmware for my RT6 2.86 B.
I want to sell the car and don't want to spend a...

Ok,

I have persistent brake squeal on our 309 DTurbo. This only occurs on very light braking.

To rewind a bit we replaced front pads and discs mainly because the front right pad set had significantly more wear than the left. The calliper sliders on right were binding.

Car uses Girling callipers

On fitting the parts, I freed up (or I thought I...

First thing, I'm not sure where to put this, so it is here in the Peugeot forum because the problem is with my 307. I'm sure that it will be moved to the correct forum by an ever-vigilant moderator.

Neither the driver's side exterior mirror nor the heated rear window of my 307SW are heating. The passenger side exterior mirror is heating. Tracing...

I have not been successful in repairing the radiator of my 205 td.

The price of new ones are crazy.
The original rad is 55mm thick.
I can buy an aluminium rad at a great price but it is 42mm thick, whereas an alu one of 55mm runs to 300€ plus

Would the fact that it is alu and new maybe mitigate against the fact that it is slimmer ?

Hi all,

Hoping someone can help clear up a genuine mix-up on my oil spec.

Car: Peugeot 2008 Estate 1.2 PureTech 130 GT, EAT8, engine code EB2ADTS
Reg: Year 2022, first registered 13/01/2023
Bought from a Peugeot dealer in Birmingham 3 months ago at 9k miles, now at 15k.

Low oil level warning came on, dipstick confirmed it was at minimum. Trying...

Hi

I was told 2021, use B71.2290 which I did.
2023 timing belt too wide > replaced.
2024 use only B71.2010
2025... now use FPW9.55535/03

Could you please crosscheck with my VIN?
vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff]

Do you recommend testing the belt throughout the year with a belt width tool? In addition to the yearly service.

Thank you!

Hello guys
I can not find any topics or advices around AC expansion valve.
Has anybody dealt with expansion valve replacement?
Do you have any manuals?
My car is Peugeot 508 2.0hdi 163hp from 2012
Thank you in advance

Hi,

I'm new here, I live in the Netherlands and I own a 2018 peugeot expert 2.0 blue hdi 180hp. I work as a mechanic on classic cars and yes als classic French cars :-)
My problem is that my engine has failed, it had an oilpump issue and this caused severe damage inside the engine. Now I have decided to install a new engine.
Found a 2023 engine...

Hi everyone.

Hope someone can help please? I am rebuilding dv6fcu in peugeot expert. I have followed torque specs when placing bearing caps on. At 10nm on the bearing bolts crank rotates freely. When the 15 m6 bolts are tightened to 8nm and the bearing bolts are backed off 180 degrees and then tightened to 30nm the crank will no longer rotate....

I have no qualifications in engineering,but I KNOW that the Prince Engine in my RCZ 1.6 is designed to run too hot.It might help with emissions and aid direct injection,but it thins the oil,aiding and abetting the terrible oil consumption of that engine,and bakes the plastic components.
I saw a post on the site whereby a member ran a wire from the...

Hi, my Peugeot Partner 2017 keeps showing left front door open which mean I aren't able to lock central locking.
I checked all wires from driver's door to connector on the pillar. I tried disconnect connector on pillar but display still showing opened door.
Can someone help me? I need wiring diagrams from driver's door to BSI. VF3**************[VIN obfuscated, can be read by forum staff]...

Hi,

Have problem with a 407 1.6hdi.
The code is p0069 and I have checked the map sensor and its fine. The fault pop up direct when the ignition is turned on, without starting the engine.

Turbo boost pressure seems correct against the actual real atmospheric pressure (976mbar) with the engine off. Checked this value with another car that also...

Hi
Think I need a new coolant temperature sensor on my 2015 308SW 1.6 BlueHdi, engine code DV6FC
Dash gauge reads 90c even when cold and dash lights up like a Christmas tree and warns me to STOP the car. Had a fun 800 mile trip back from France in limp mode the whole way!!

Anyone know where the sensor is located on these cars or is it a permanent...

Can anyone recommend a suitable adhesive to stick the cover back on the outer rear light of my Peugeot 307cc, This seems to be a common problem, they appear to be heat welded at the factory but it wasn't very successful. I tried clear silicon adhesive sealer but it caused the lenses to crack and eventually crumbled and lens fell off again. I've...

I need to replace the front suspension roll bar links on my 307CC and doing a search for the parts I see a vast number of the correct part available by different manufacturers. For instance:Ridex, Monroe, Delphi, First Line, QH, SKF, TRW, FAI, Borg & Beck Febest, etc. The prices vary from about €9 to €22. There are loads more makers names that I...

Not sure if anyone has come across this fault before. 2020 Peugeot expert central locking will lock all doors with the transponder fine. However it only unlocks the ns sliding door with the transponder. All other doors need to ge opened with the key in each lock. I have checked all fuses and selective door locking options all OK.

Hi all, my friend has an issue with his 407sw 2.0HDi
The engine management light comes on after 3 cycles of starting the engine. The engine loom was replaced at some point but from what I have heard it's come from a coupe model. I don't know where to go from here as we've tried 2 MAF sensors so I'm sure it's wiring. Anyone know what the pin out is...

Hello everyone,

My car has 44,000 km on it, and I was about 1,000 km late for the oil service. Afterwards, I started hearing a rattling-like noise when I press the accelerator, similar to the sound in the video.

Does anyone know what might be causing this issue?

Hello, I have a Peugeot 306 1.9D 1998 and I need a scheme for the pins between the front doors and the car. I need to know which pin is for what.
Thank you for help.

Hello to all from a very scorched Morbihan.

Re-visiting my Peugeot 306 with the DW8.

The previous owner was a bodge the builder but the body and interior are in nice condition.

I have fitted a replacement cyllnder head and injection pump. set the valves correctly and fitted a new timing belt kit.

It starts easily, no smoke, correct amount of...

Hi can anyone tell me what engine code my 2018 2.0 hdi blue 130 would be
Thanks
Tim

Hi folks, New here; thank you for having me. I have tried another forum, without success.

. Basically the ASR light is on the above vehicle. No mil or ABS light on.

The ABS is working and all the wheels are reporting the same speed. On diagnosis it is showing a fault brake pedal incoherence (i have loaned my unit to a friend so cannot remember...

on a similar year car

can I put in a 308CC steering wheel into a normal 308? both steering wheels are just the regular airbag ones, not the later ones with controls on.

I suspect yes, just want confirmation.

ta

Changed timing chain on ep6 engine. There is a tolerance gap up to 2.5mm between the intake and exhaust locking tools on the instructions. Should the intake tool be bolted down or not? as this makes a big difference to the gap

Hi can anyone help me 2.0L Peugeot 2015 508 hybrid ? So my wife started the car in the morning and stop car engine fault popped up in the dashboard, she stopped the car and since then won't start . I checked fuses and I found a 5amp fuse blown on top of the battery on the bpga I belive its called I changed it and notthing . I checked bpga and...

Hi everyone,
I have a Peugeot 607, 2007 model, and I'm having an issue with the trunk/boot:
When I first try to open it, it starts vibrating/shaking.
Then it only opens a small amount (not fully).
After that, it vibrates again and doesn't complete opening.
Has anyone experienced this before? Could this be related to the trunk motor/actuator, the...

Hello guys.

I have a 2003 2.2 HDi Peugeot boxer (244 shape) on 102k that seems to pressurize the coolant, this results in a catch bottle (from coolant bottle over flow pipe) being filled and the low coolant light coming on anywhere from 50-250 miles, usually lasts longer if constantly rpm on motorway. Sometimes the light will come on when idle...

A year ago I bought a Peugeot 5008 manufactured in 2010, 2.0HDi, RHE engine, completely flooded, which had been in the water for about three days, with 85% of the electrical part being compromised. It was flooded in 2022 and since then the car has been stationary, the owner wanting to sell it entirely for spare parts and remove it from...

Peugeot 3008 1.6 active HDI 2016
Water coolant leak at the back of the engine towards the right side (battery side)
Started small now having to top up every time I use the car
I think its coming from the pipe in the photo ,if not is just above it but really difficult to access
I thought it might be the thermostat housing?
If anyone can tell me...

Hello everybody,

The AC on cooling have a fault, its only work for few seconds every 10minutes, blowing warm air.
If the car is parked in the shade, work more often, maybe every 5min for couple of seconds.

Car is currently in a limp/safe mode, have a check engine info.
Engine fault and safe mode is about dpf probably, but it is possible that...

Hi, I am currently having issues with a hard brake pedal a low revs, enough so that it has come up as an mot fail. At higher revs it seems to produce enough vacuum to keep the pedal soft.

I was wondering if anyone had any experience in replacing the diaphragm of the vacuum pump vs the whole pump as these are available at about half the price ?...

Hello everyone,
I am hoping a kind member with Service Box access could help me pull the official factory build sheet for my Peugeot 508 Fastback. It is a UK launch model with the badge Number 35 out of 200 and the 225 BHP petrol engine (VIN contains F35). I am trying to verify the exact factory interior configuration, specifically relating to the...

I changed a cam belt on a 2017 Peugeot 2008 1.2 turbo, the EB2DT engine (HNZ code)

Now i have it back together the engine seems to be running fine but i have the EML light on and its saying P0011 - inlet camshaft dephaser locking.

I used the correct locking tools and paid for to download the official manual from servicebox. The sump was...

Hi everyone,

I recently bought a 2021 Peugeot 308 GT Hybrid from a professional dealership, and I would like to know the full factory equipment list using the VIN: vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff].

I am especially trying to confirm if my car has Blind Spot Monitoring. From what I understand, it should be standard on Allure and above. I have the two small LED...

My Hdi alternator has developed a voltage drop issue after a long run. Voltage is normally around 14.5 volts but after a long run (say 100kms), it will drop to 12 volts and continue downwards, suggesting its has stopped charging.

If I spray the alternator with a hose or even a water bottle, it jumps back up to 14.5 volts and will run fine for a...

Good evening, I have a 2010 Peugeot RCZ with the 2.0 HDi 160 hp engine (engine code RHH). While dismantling components to access the valve lifters (which I needed to replace), I accidentally disconnected the hoses from the turbo control solenoid valves. I reassembled the engine and the car runs, but it’s throwing a fault because the turbo is...

Hi

My intercooler air hose 03845J2 is fine but the seal to the air intake resonator 163614 is perished / has a few splits in it

It appears you can't buy the seal by itself, only the complete hose.

Has anyone found a replacement seal that works ? It seems it 54.5MM diameter

There are seals available for the 1.6L part 1434C8 but I assume they...

Hi everyone,

I have a Peugeot 207 1.4 Semi-Auto with the KFU engine, and I’m experiencing an issue where it idles at around 1500–1600 RPM. I purchased the car with a gearbox problem, which initially prevented the engine from starting. Since then, I have replaced the clutch, clutch actuator, and serviced the vehicle, including replacing the cam...

Hello everyone,

I’m currently searching for scrapyards in the North West of England where I can personally remove parts from Peugeot vehicles. Specifically, I’m interested in self-service scrapyards.

If anyone has recommendations or knows of any suitable scrapyards in the region, I’d greatly appreciate your input.

Hi everyone,

I'm looking for some technical insight from people familiar with PSA electrical systems.

I have a **Peugeot 308 T7 THP** (Brazilian market, manufactured in Argentina).

My original **Delphi BSM R05 (ending in 8480)** failed after the A/C fuse overheated and melted the fuse holder. It also left the low beam relay permanently ON.

I...

Hello,
I am in need of changing the timing chain for the first time since i got my rcz, i would like to ask why is there a timing chain kit from febi one with 138 links and other one with 144 links and which one to get. We are talking about 2012 rcz 1.6thp 200hp.

Cheers