French Car Forum

I made the stupid mistake of buying a 2019 peugeot boxer with a knocking engine thinking I could either put new shells in it or buy a good engine.

Life took a turn (I got a full time job) which left me with vey little time so I contacte an engine rebuild company who said they could do it but didn't know when as they already had a huge queue of...

Hi guys,

I've recently replaced intake manifold gasket with Victor Reinz one (0348.V7 catalogue part) along with injector seals. Still having some smoking from that part so I suspect 0348.V7 O-ring might be the culprint. I didn't know about it before I started so I left the old one.

My confusion is that Victor Reinz supplies only the seal...

Hello all

Any tips on how to remove these from a Peugeot 308cc? No bolt but not sliding out.

Thanks
Justin
PXL_20251210_194248614.jpg PXL_20251210_194250482.jpg

Hello everyone,
I’m Have on a Peugeot 508 SW II from 2020 (BlueHDi 163, VIN: vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff]******76) that recently lost multiple functions at the same time — high beams, horn, washers, mirror indicators, interior dome light, and several HVAC functions stopped working.

A technician scanned the vehicle using SMOK and Xtool, and it looks like the BSI...

Hi, I have the issue in my 2016 508 1.6 Diesel where intermittently, I get ABS, ESP, Anti Rollback and parking brake alarms coming on. When I switch off the car for a little while, the faults are gone. I had some other intermittent faults with doors and Electrical Fault service car or something similar. I bought the car last October and this...

Hi, can someone point me why i have this errors i am worried about Permanent and what can i do about it?

Peugeot_308(T9)_2014_VF3L35FVGES029395_1765209151467_56773069.pdf

Now that the car is secured by means of the windows having gone back up, I can turn attention to the reason why the car was towed instead of driven home. It doesn’t start. And it doesn’t even crank. There is nothing that comes out of the engine.

In the other thread, I posted some pictures from Diagbox that I believe show something other than the...

Good morning, I own a Peugeot 207 cc 1.6 vti, I am writing to you from Spain.

Hi all,
All advise appreciated on this issue. I have a 2012 2.0 hdi 163bhp that when fully warmed up will sit with a high idle of around 1300RPM. This reduces to normal idle (800rpm) when the brake pedal is pressed but goes back to 1300rpm when released. It will also drive at this rpm when the accelerator pedal is not pressed i.e. 50mph in 6th...

Hi All,
I recently purchased a new Peugeot Expert 1.5 diesel van. It's my first van that requires adblue. At about 6,000 klm I got a dashboard notice that adblue was required so I topped it up. After a short drive the adblue dash light went out so all ok. As I approached 10,000 klm I was presented with a count down informing me how many kilometers...

Hi Guys,
I am new here and have this PEUGEOT BOXER 335 L3 H2 2.2 BLUE HDI 140 VAN.
I installed a cruise control lever as the VAN did not have it before.
I am looking for any app/tool for enabling/programming the new lever to the vehicle.
Any idea?
Thanks a million

Hello all,
Oddly I didn't find much on the Puretech engine here. Probably didn't search properly. ;)
I own a 2018 5008 with the 130hp 1.2 and as someone who purchased her only a year ago, am fully aware of the history of issues with this engine. As such, I change the oil every 10k km and check the belt. This time when checking the width of the...

Hi Everyone

First post.

I've got a 2.0 bluehdi 180 Traveller. I'm running lowering springs but the dampers are not firm enough.

I've noticed that the Bilstein 47-329485 is listed for the
Expert 2.0 Bluehdi 180
Traveller 1.5 Bluehdi 100

But not the 180 Traveller. I find this strange. The expert must be in the same ballpark for weight. The...

Hello,
I'm in the middle of doing the timing belt on my 2018 5008 and while taking the crank sprocket off, the oil pump sprocket tried to follow it and when I pushed it back on the crankshaft I noticed that the chain is quite loose. I almost thought it came of the pump sprocket, but that's fine.

I can't find specs anywhere. The chain looks fine....

Im having an issue where the boot thinks its permanently open so wont lock but also I have none of the interior lights working when opening doors. All reading, sun visor lights work just not main ones.

Its a 2014 peugeot 3008

Its bsi04 ev k01-00 071113

Can provide the vin if needed. Ideally looking for some guidance to where to look on the bsi...

2014 5008 1.6 hdi

The radio and the pop up multimedia screen have stopped working in my wife’s 5008. Also the parking sensors have stopped working too. The radio is also now making a noise like it is trying to eject a CD, but there is no CD actually in the CD slot. There is no SD card slot on the radio. I have checked the fuse F8, which was fine...

I'm currently battling yet another problem with my 2006 Pug 307cc, 2litre 16v (143hp). Once again it won't start and I have explained all in the Diagnostics section. I would like to top up the battery but vaguely remember reading something about having to reset something (or everything) if the battery is disconnected. This would probably compound...

Car is a 2008 Peugeot 207cc 1.6 l petrol. It starts easily enough but can idle rough. It can stall when coming down from high revs, or even down from a steady rev. The Engine Management error message comes on at changes in engine speed, with the warning orange triangle. The triangle can dissappear if steady revs are held, like on a motorway.
No...

Hello dear all,
I found the EP3 guide, is it also the same guide for EP6?
Do I need to bleed air outside with cap open or not? not sure, also some friend of mine not sure, he's not a mechanic but it's his hobby

I also found the guide of 207, which states opened cap, in the EP3 guide, closed cap

Thanks,
Golden

Hello, I have a fuel problem with my vehicle and I haven't solved it yet. The car is burning too much fuel. The Maf sensor, upper Lambda sensor, VVTI valve, and PCV valve (upper cover) have been recently replaced. The High Pressure pump has been recently overhauled. Injector corrections have been flawless. I used Rislone additive for catalytic...

Hi I have a 2024 Boxer (from new) with 10k miles.

yesterday the engine management light came on. Didn’t real like it went into limp mode but did notice loss of power up hill….

Light was on again this morning. Moved the van (was in the way) and the light has gone out again 🤷🏻???

Peugeot can’t look ant it until Jan 8th

The error code is (was)...

Hello all

I have been searching high and low for help to wire in an RCC and so far found very little help. So I did my own research and have come up with this:

Screenshot 2025-11-09 at 23.48.05.png

pins blacked out are unused. I hope this might be of help to someone. Please let me know!

Hi all.

I'm hoping someone can help me as I'm at my wits end with my peugeot 3008!

I've recently had my alternator completely die on me and left me with a dead battery. I have had a mechanic replace the alternator and had a brand new battery fitted.

The car now has on the dash ESP/ASR system faulty and the engine fault: repair needed. It's...

Hi
I need to find the route of the LIN wire that comes from the 1 pin connector on the alternator and goes either to the PSF/1 or the BSI on my 2010 3008 1.6HDI engine code DVC6 9HR VIN No VF3**************[VIN obfuscated, can be read by forum staff] , the alternator will not charge unless I pull out and then reinsert the F3 fuse on the battery fusebox.
I've changed the alternator, BSM and...

Hello!

Recently I have noticed that my car does not accelerate like it should in D but when i switch to M it goes like it should, so i hooked up DiagBox and did some measurements on the gearbox, the results are in the attachments.

1. D only -> It slips like hell the torque converter almost never locks up.
2. M only -> The torque converter is...

I changed the upstream nox sensor of my peugeot 3008 bluehdi 1.5 2018 vehicle due to dreaded P02EE error code.
However ,after driving the car around to get the nox heated up to optimum range ,i still notice the upstream sensor live data didnt deviate from 0 value regardless of speed just like the previous one.However downstream shows activities...

Good day everyone

I have a 2025 bus with a 2.2 HDI engine.
Before restyling, there were also 2.2 engines with the code DW12 (RUE, RUD, RUC)

New engines code:
B22LUF(46356294) - 2.2 HDI 88KW
B22LUE(46356294) - 2.2 HDI 103KW
B22LU?(46356294) - 2.2 HDI 132KW

Question: What kind of engines are these? Because I couldn't find any information.
There...

Not sure if anyone has come across this fault before. 2019 Peugeot expert central locking will lock all doors with the transponder fine. However it only unlocks the ns sliding door with the transponder. All other doors need to ge opened with the key in each lock. I have checked all fuses and selective door locking options all OK. Would anybody...

Hi. I had timing belt, drive belt and water pump exchanged on my 206 SW Petrol Year 2005 one week ago in a garage.
Before the exchange the watertemp gauge went up to about half of the scale, as it should do.
The engine works fine but one problem has occured after the job.
The watertemp gauge is not showing correct temperature. In fact it doesn't...

Hi, first post here. Name is Logan, from Sweden. Bought this charming Peugeot 106 XR HDZ year model 1992. The paint is quite faded and I thought that I could at least try and touch it up some. I can't really find the color code for it, I looked at the driver's side shock absorber and I can see faint faded letters that I cannot make out. Neither in...

I have a 508 SW 1.6 e-HDi 2013 6-Speed Robotised Manual Gearbox. Its about to reach 270000kms and while it still works alright It has been showing its wear i believe. Such as when it downshifts sometimes it has a hard time shifting to a higher gear. Not necessarily slipping big time because the spedometer still goes up but not as much as it should...

Sup everyone.

Im very interested in buying a 406 Coupe 3.0 V6 and the one thats out there is pretty much in mint condition. Only done 160k kms. Seller states that hes changed the trans oil twice which is not bad in my eyes. My only concern is how good the price is alongside sellers eagerness to wanting to sell it to me rather than the guy coming...

My wife’s 2011 year model 3008 is in a state of not starting. (Cause is as yet unknown.)

But the immediate problem is that both front windows are open and the car is in Economy Mode.

I know that the battery is in good condition. Well, I replaced it earlier this year, so I’m presuming that it’s fine.

Thanks for any help you can offer me.
Andrew

Hi,

I have posted in the past about my Citroen Xantia but need help with my Daily driver a Peugeot 807,

Friday just past I drove far too fast through flood water and ripped off the (what I have researched to be the fuel cooler) under below the passenger seat.

Got out tied it up and started to drive home, Almost made it before it cut out. Toed...

Hi everyone hoping someone can point me in the right direction. 5008 1.5hdi headgasket went replaced the gasket. Car wouldn’t start then found out the timing chain had stretched, replaced the chain and cams. Still can’t get the car to start only fault codes coming up are starting monitoring anyone else had this issue

Hello!

I believe that my cars are conspiring against me. I had a stinking cold and haven't been able to have another look at the issues with the RCZ, now the 308 seems to have joined in.

It has decided that as we are in the coldest part of the year that it would be fun if no heat came out of the blower in the cabin. As I also found a relatively...

Got rid of most faults from before just 1 left p2565 fixed geometry turbo position measurement short circuit to positive or open circuit any ideas thanks in advance.

Can anyone advise on options when installing a replacement (used) BSM.

58 plate 307cc (2.0 hdi)
I've got a few faults on scanning that are persistent and seem to point towards a failing BSM so was considering a cheap replacement off ebay as a lazy way of avoiding checking through the spaghetti of wires. Obvs risking buying a faulty unit if used...

Hi!

We have a Peugeot Expert 2007 with a DW10UTED4 / RHK engine and a Siemens VDO ECU SID803A. VIN: VF3**************[VIN obfuscated, can be read by forum staff].

An engine swap was performed. Only the block and the head were replaced; all the electrics, fuel system (except the pump), and other components were retained from the original engine. The reason for the swap was a failed...

Purchased a Peugeot 206 1.4 a little while ago and I am currently trying to fix it up back to near factory quality. I have found that the previous owners swapped the engine to the 1.6 engine with ought changing the throttle body, coil pack and a few other components. I have got my hands on a new and correct throttle body and coil pack, however the...

Hi,
I decided to renew the X2 full length, rear wheel Brake Pipes on my 1.4 SE after discovering that my Hand held flaring tool could not FLARE the original High Carbon Steel, PSA pipes.
My idea was to take the easy route and simply use a pipe JOINER piece between the original STEEL and the new COPPER repair section.
My trusty SUPRA hand-held...

Hi have a peugeot 307 estate i have a 2 button key was trying to find out if I can upgrade to a 3 button key my car has electric boot and would like to have the choice on my key has anyone done this before ?

Hello all,

Starting issue with our Bipper van hoping someone could advise.

Not starting with key in third position, makes no effort at all, no clicks. Everything else, dash/lights etc. are working and battery has been charged. Thinking something with the wiring but struggling to get any diagrams etc with where to check and the weather/location...

We are giving some TLC to a 2009 207 1.4 that has been off the road for a while. It has 80k on the clock, it had an emissions light on and idled like it wanted to stall.

Live data revealed a dead post cat sensor. We changed that, told the ECU it had a new sensor and took it for a good drive. It now runs sweet as a nut when warm. However, when it...

WhatsApp Görsel 2025-11-21 saat 19.35.14_ca4275fb.jpg WhatsApp Görsel 2025-11-21 saat 19.35.14_a3a1d9f0.jpg The roof control button of the car I bought a week ago is broken. I want to repair it, but it didn’t fit properly in its place. I want to produce a new button with my 3D printer, but I couldn’t find an STL file. Do you have one, or how can I...

I drive a Peugeot 308 1.6 HDI with a DV6C engine. I'm tired of cleaning my car's particulate filter. I live in a city with heavy traffic, and driving at high speeds isn't feasible. When I'm on the intercity, even if I'm constantly cruising at high speed, it doesn't seem to work. I remove the particulate filter and wash it with pressure wash and...

What is the latest version of Diagbox currently used in authorized service centers? Which VCI is it used with, and how can we access the VCI and the program? Does anyone know? Thank you.

2009 partner teepee 1.6hdi
Heater. Blower stopped working checked fuses. Powered Motor manually al? working. Nothing ?on speed control switch. Resistor replaced four months ago. Now not working again even on speed 4. Should there be power in the resistor plug coming into the resistor as thhere is not.. Could it be a fuse. I haven't located or...

2005 307 2.0hdi 136.

New starter motor and fuel filter fitted today.
During the process a broken clip was found on the fuel line at the filter, however it refitted with the piece in place, holds in position and doesn't leak.
After the job was done, when air was purged from the lines and it started as it should .
Now it turns over for 3 or4...

Hey all, im new here so I hope that I put this in the right subject. Sorry for my English btw. Don't expect it to be the best.

I have a question about the car I drive, I'ts a Peugeot 508 SW 2.2L Diesel from 2011.

I wanna install a module so I can use carplay in my car. Is not like a complete new radio but just a module so i can use the original...