French Car Forum

Good evening everyone

I have issue with my hybrid system, the clutch on electric engine is not engaging so I have replaced the whole engine and diff with another working one but it’s still throwing this code P1ABF. I don’t know where else can I look so if someone can help me I would very appreciate that. Thanks...

I have just had my MOT done and when I was leaving the ESP /ASR warning light came on when I started the car it is a Peugeot 207 cc. I can still drive without any problems but needs sorting. I took it back to the garage where I had my MOT done straight away but he said it was alright after the test but it wasn't. They did a diagnostic test for...

Hi all,
My unit lost satellite connection and my navigation is dead. I have had this problem since I bought it back in 2023. Now I found identical replacement unit matching all numbers but it needs VIN to be entered. From this forum I learnt that only Diagbox could do this but still hoping that some other third party tool could do it as I have no...

There is a grille at the bottom corners of my 307 SW windscreen.
They have split and the the edge that sits against the glass is curling up and not sealing.
I have searched and not been able to find any parts diagram that shows them except for the one posted below. It came from another forum but has no link to its origin.
The parts are NOT circled...

Hi everyone. Iam new to the forum. I have search ed everywhere but cant find which eolys fluid i should use for my car. I have a peugeot 407 from 2004. The eolys fluid tank CAP is White and My vin nr is VF3**************[VIN obfuscated, can be read by forum staff].
Thanks you!

Hi
I've got some trouble with my '08 308 1.6HDi. The other day it refused to start- it just turned over sluggishly, classic dead battery sort of behaviour. I had left a trailer plugged in overnight but there were no lights on. I wondered if maybe that had upset it.
Anyway, I'm in troubleshooting mode now and have deduced the following:
- the Pug's...

My 406 1.8L LFY is going to limp mode without indicate check engine. ODO is at 98000miles.
Scanned with lounch scanner tool and unable to find any issues.
Specialy if I floored the accelerator and jut after reaching 3000rpm i feel like a loss of power. And after turn off car for around 15 seconds car works normally until it reachs 3000rpm and...

I have a Peugeot expert tepee 2.0 16v from 2008.
Vin is VF3**************[VIN obfuscated, can be read by forum staff] so it should be an ew10a RFH engine. Considering the high mileage that the van has got I am thinking of doing a swap. Only thing is, there seem to be a million RFJ engines but not a single RFH in all of Europe. Does anybody know what the differences between the 2 are, if any?

Hiya! I purchased a 2008 2017 plate allure today and trying to use the sat nav function, can someone help me to make it work? I don't mind if I have to pay for the functionality but i feel like there's something I'm missing here

I have tried connecting via Bluetooth (works fine and music works and calls etc but cannot get the sat nav to work)...

Hello guys.
I have just bought my self a Road Angel Halo Play 4K Dual Dash Cam to put in my 2008 (manual 2025) and i am looking at doing it my self, But i am hoping you guys are able to help me with a few things i am unsure of.
1: I attempted to access the fuse box inside the glove box but it takes a considerable amount of force and i am concerned...

Hello,

Just a quick question, do anyone know what kind of oil should I use as replacement for Peugeot 508 Hybrid 4 for rear differential and gearbox? I heard from local dealership that this is lifetime oil, they don't recommend replacing. As I understand I should wait till gearbox end it's life ;) Every oil degrades. Additionally where can I...

Hello

After I did interior cleaning on my VTS, neither of my heated seats work. I didn't kneel on the seat, I just reclined and slid them a lot. Fuse is OK, light on heater control works.
What to check next?

Hi!
If anyone would be willing and able to, I need two wiring diagrams. The ones from the offline Sedre I have are not complete and also seem incorrect.
I need the wiring diagram for the COM2003 unit, Peugeot 407, build year 06, OPR10938
And the diagram for another 407, but with the COM2008 unit, unfortunately don’t have VIN/OPR.
Any help will be...

I am having difficulty programming the transmission after a clutch change on Peugeot 3008 1.6 HDI 2013 model.
Using an Autel scanner in won’t complete the clutch biting point phase of the task.
The car has no fault codes and can't see a reason why it won’t complete the program.
The picture shows the message I get.

IMG_3694.jpeg

I have tried...

Back in August 2025 I purchased a Peugeot 3008 PHEV Hybrid AWD or so i thought. It is the petrol 1.6 PHEV automatic. Fantastic car but recently developed a creaking noise audible at low speed from the front and felt through steering wheel. Garage couldn’t find anything so I started looking around. One online forum suggested sometimes the 4 wheel...

Finally got the door cards etc from the rears, and yes you guessed it mo speakers but luckily wiring there. bought new speakers to fir that come with tails. one end obviously goes to the speaker the other are just bare ends. The vehicle has connectors, can i buy the bits that plug in or should i cut and splice. Have googled but cannot find the...

Hi all,

Thanks for the add. I have an issue with my Peugeot partner hdi van stereo, model RNEG2 CEM00 after i added a new stop start battery to my it. The stereo head unit has stopped working. the laser disc inside keeps spinning around but doesn't boot up. Is there any way i can buy a boot disk for usb or boot cd to overwrite the sd card in the...

Sometimes when I’m driving in low speed the car just turns off i put it in N and it just turns on again, yesterday I tried to turn it on in the morning and it was just cranking with no start, after several attempts it started i drove for like an hour, parked for like 10 minutes and then tried to turn it on again and didn’t start after so many...

Can anyone advise if my unit would be a plug and play swop or need programming/coding.
What info do you need. Car is 2015 1.6 hdi 120
308sw

Thanksc

Hello everyone,
I have a problem with my 508 HDI 163 Keyless. The problem is it won’t start. I can open and close the car with both of the keys. Battery has been charged, key batteries has been changed but pressing the start button makes no change. Putting the key in the key holder doesn’t help. I have disconnected the battery twice - all the...

Hello!

Is it possible to remove the gearbox without removing the chassis frame, or does it have to be removed?
Thanks in advance for your help!

Can anyone please help? I can not understand why this error keep coming up! I have changed the BPGA, changed negative terminal on battery, brand new battery programed with diagbox, cleaned everything and every connector to the bsi and ecu(no corrosion present), all fuses are good, I keep getting P0685 intermitent most times, but sometimes it shows...

Dear All
My recently acquired Peugeot Partner Horizon 2007 wheelchair access truck, had been behaving itself recently, once all the myriad of post purchase gremlins were addressed.
I thought all was well until an unnerving amount of understeer forced me to the kerb and bent (not too badly) the OSF wheel. I put the spare on and went on my way, and...

I do not have a service book of the car, can performed service be found from VIN. number?

Hello,

And greetings from Finland! :wave2: This will be my first post, and unfortunately a long one. I'll try to include as much information as possible, in case anyone would be able to help me in this matter. I'm getting quite desperate... :(

I recently bought facelift Peugeot 607 2006 2.2 petrol (produced in july 2005, older model) and it's...

Here's a question that I should know the answer to - but I don't. Hence why I'm asking.

Every query I put into a search engine comes up with this kind of picture showing the BPGA that's fitted to the Mk2 Peugeot 308.

308 T9 BPGA-1.jpg

But I don't have one of those in front of the battery. There's just an empty space there. Now it does make...

Hi,

Peugeot 508 RXH Hybrid4 2012

I had a leaking valve cover gasket which was spitting oil on the firewall side (car's right hand side). Changed the gasket without fully removing the cover as it has hard to reach rubber pipes at the firewall side. No more oil spitting but my fuel consumption is now 8.0+l/100km and have faint smoke from the...

Here we go again.
I live in the wettest area of France and have no garage. As a result I am trying to find out why or where the rain is getting into the boot lid. Every time I open it water pours out of the lid hits the cill and splashes into the boot. The carpet is alway soggy and is eventually going to rot out the boot floor. I can not work out...

Hello, can I find out what extras my car came with when it left the factory?
vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff]

Both front windows stopped working. 2015 Peugeot 2008. Rears are manual. Where is fuse please and where next if fuse ok. Thanks

Hello Good people.

I am planning to buy a used car from a dealer.
It is a Peugeot e 3008 GT With GT-Pack and much more.
The car is imported, and the dealer has no Build Sheet on it.
The dealer's system in Denmark can not pull a Build Sheet before it is registered to a buyer, me.
But the car is listed with everything and I would like to be sure...

Hi, I am trying to REMOVE a wheel bearing with ABS RING, on my 04 plate 206 - I tried to PRESS this out using the old fashioned BOLT and WASHER extractor method, to no avail.
Is it POSSIBLE to REMOVE both the old bearing + ABS RING at the same time ? (to-gether).
The BEARING has a 52mm Outside DIAMETER and the ABS RING has an internal DIAMETER of...

Hello, may I ask for the RT6 head unit pinout for this VIN: VF3**************[VIN obfuscated, can be read by forum staff]? I found out that they are different in each version and I want to be sure.

Hello. Two weeks ago I had a problem with one injector (lean mixture in the cylinder). As it turned out, it was a problem with the piezo element closing to the injector housing. Since I had already done this and I have experience in this, I removed all the injectors myself and took them to the service for inspection and repair. I installed the...

Hello to you all!

I am new on this forum and I am hoping that I could find some help in order to solve the problem which I encountered on my Peugeot 508 RXH, 2017, BlueHdi 180hp.
I've read all the forums I could reach in searching for a solution, but so far no luck.

For almost two months I’ve been trying to figure out what happened with my...

Hi all. I'm new here hoping somebody can help me out. We did a battery change on our 3008 2012 diesel with auto gear change (manual box) without following the correct procedure
It wouldn't start, came up with engine fault, handbrake wouldnt go on and it says it's stuck in m-
It took me a while to get some advice. First I thought bsi and was all...

Hi everyone!

I desperately looking for any advice to find the problem with my car, because i'm out of ideas.

The car is a Peugeot 407 2.2HDi 170 which ran fine until one morning it simply doesn't start.
Diagbox indicated an intermittent P0341 camshaft sensor - signal absent error, so I thought an easy fix. I bought an ERA aftermarket sensor,...

Hi,
Firstly sorry if this is an obvious one, and I’m just being slow or not looking in the right places,
I’m based in Glasgow, currently about to get my first works van, a Peugeot partner and it doesn’t come with Apple car play, it is a 2020 plate and it has the infotainment touch screen.

I’ve seen online it’s not available to buy the upgrade...

Hi got peugeot boxer 3 with air bag fault,3 codes set
1 u0019 can fault
2 u 1703 comms with instrument panel
3 Bo100 ecu internal fault
No 3 I think is common fault ( ECU REPAIR) Let me know if you think different
What I would like if possible, a wiring diagram for air bag system please to help me check out unit
VIN No=VF3**************[VIN obfuscated, can be read by forum staff]
Thanks...

Help request – Timing timing / VVT pulley preload Peugeot 207 THP 150 (EP6DT)

Hello everyone,

I am in the process of replacing the timing chain on my Peugeot 207 1.6 THP 150hp (EP6DT), engine identical to the N14 Mini.

I used the shimming tools to lock the camshafts and crankshaft. Everything seems well aligned mechanically. Before the change,...

Hello,

I have 2021 Peugeot 508 SW Mk2 2.0 blue hdi VIN vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff].

I'm replacing the front and rear discs and pads and to do this you need to remove the disc caliper from the axle. Can anyone provide the tightening torque settings for the bolts which hold the calipers to the front and rear axles? Also the bolts for the pad retaining frame...

Hi all,

so suddenly my 508 (1.6 bluehdi 120hp) started making very loud knocking noise, which I assumed to be engine knock at first. The noise mostly happened during idling, but the car was really loud in general. Upon investigation, I narrowed it down to a loose flexplate. I assumed I'd only need to retighten and glue these bolts, but couldn't...

My Peugeot 806 suddenly died when driving and wont start.
I have tired/checked the following:
- Gasoline pump wont start when turning ignition on
- When cranking the starter motor will crank but there is no spark
- Replaced double relay, still the same
- Tried to connect 12V directly to the fuel pump (through double relay plug), the pump starts...

Hello.

I have a sunrooof drain leak into the cabin on my 309 which has the factory sliding sunroof with the vacuum seal.
On peeling the headlining back, I can see that the front corner drain tubes from the sunroof tray are quite corroded and weeping slightly.

It copes with normal rain ok, but not so good with washing the car when large volumes...

hi guys,
I'm hoping someone can help, I'm looking for the part no for a clutch kit for my peugeot expert, Its a 2005 2.0 hdi dw10ted4 with a solid flywheel, & ml5c gearbox been looking but all i can find are kits for dual mass flywheels or conversion kits, problem I'm having is the releaser keeps pulling out of the pressure plate, clutch was...

Is there an easy way to identify if my 2008 307SW Hdi has Bosch or Lucas/TRW front brake calipers?

Not sure yet if I need new calipers or just a service kit for the glide pins, front offside brake binds and only the fixed pad shows signs of excessive wear.

With Thanks

Alternator pulley disintegrated and was found lying on the sump guard, leaving just its innards still attached to the alternator 😢.

I have the M10 splined bit and associated nut required to remove the pulley and these do just fit with the alternator in situ, but I was just wondering before I invest in any more tools has anybody successfully...

I've posted elsewhere about rough running on my wife's 207cc, 1.6l petrol, 2008.
I am now getting a consistent Exhaust Camshaft Dephaser too far advanced. I've changed all the sensors, check static timing and I am now changing out the Dephaser sprockets. Feeling my way with this, not a job I've done before. Got the Ex. Dephaser off and it seemed...

hello everyone.
I have a 508 RXH hybrid4 that just won't stay running. If I clear all the code with diagbox(9.85) and I remove the traction battery cable from the hybrid battery itselfe ,the car starts for a few second then dies and a lot of errors pop up.After the small start I cannot start the car again if I don't cleare all the code again....

Hi, looking for some advice, I have a peugot 207cc 2010 that has an engine warning light and some error codes that I'm struggling to troubleshoot.

P2178 - mixture adjustment
P1336 - combustion misfiring
P1337 - misfire on cylinder 2
P1338 - misfire on cylinder 3

The car is juddering, pulling back and losing power. I replaced all sparks and...