French Car Forum

Good Morning,

Trying to track down a gearbox for the above - my issue is that when it was swapped out in 2015, a 1.6 gearbox was mated to the DV4TD engine but I dont know what gearbox code it is.

Does anyone know what gearbox code(s) for a 1.6 HDI fit a 1.4 HDI engine, its starting to drive me bananas as no one is willing to help very much as...

I have a 1996 406 with the 2.1 engine, it had the lucas epic pump but had a few issues with idle, random unintended acceleration, random spluttering and fuel leaks. So i have removed that setup and fitted a bosch from a 405 1.9 TD that i removed back in 2017.

The 406 is starting now on the bosch pump but is quite smokey and doesnt seem to want to...

Thanks for the acceptance.

Had a problem with the roof last year with it not going up properly. At first it raised about quarter of the way and just stopped, put it back down and tried again, this time it raised a bit further. To cut a longs story I had a guy test it with his diagnostic whilst I operated the roof. It folded down ok and whilst...

508sw front coil spring broken, all i know is colour code which is 2 white and 1 blue, would like to know part number for late 2017 facelift model, any help would be great because all i got are the dealerships saying they can quote me for some but wont give out the part number, thanks to all that may be able to help me out.

Hi my Peugeot 308cc 1.6 vti 5fs engine has gave up so planning to replace engine . The price of a 5fs is to much for me but I've come across a 5fw with low miles . Would it be possible to fit the 5fw in my 308. Thanks

Hello friends.

Around 20 000 km before, I had a problem on my AL4. The gearbox was sometime dis-engage on the fly and went to downgrade mode. Hence, I surfed the info from the internet. Finally, I did replacement of 2 pressure regulator valves on the hydraulice valve body. But I did not update any firmware as recommend on the sites because...

Hello All,

I’m looking for a bit of advice after drawing a blank trawling the net. My wife’s 2010 207 vti started to be difficult to unlock at times with the fob, you often had to be fairly close to the car. So, I changed the battery and now it doesn’t work at all! I followed the resync procedure in the handbook and nothing. I have also tried a...

Hi,

I have a 2008 Peugeot Boxer, Puma 2.2hdi engine, Denso injection.
The engine was replaced (complete, including injectors) however the new injectors were not recoded into the van's ECU programming.

The original codes that are programmed are 16 characters long, however current injectors only have an 8 character code that the diagnostic program...

Hi guys, just wondering if anyone has a fuse/relay diagram for a Peugeot 508 2015 2.2. I’ve looked and looked on the net but can’t seem to find anything. Just wanted to know what fuse and relay did what that’s all.

Thank you

When i drive over 130kmh for while and then press the break to slow down the vehicle the transmission not working.
If i drived on a speed less than 130kmh there is no problem
VIN

VF3**************[VIN obfuscated, can be read by forum staff]

Hello everyone - Peugeot 308 Hdi 2010

I recently replaced my abs pump and now my brake pedals have zero resistance and are floppy. Could anyone point me in the right direction, what is the cause?

I have bled the brakes twice and bled the ABS pump using a scanner. I am also getting a new fault code - C 1389 brake fluid level too low (the brake...

The power steering pump stopped working while i was driving and when i turned of the engine and then turned it on again the problem solved. But the problem keeps recurring. I need to know why?

I did these actions:
I checked the fuse box
reconnected the earth wire.
I used a tie rap to fix the plug of the pump.

I still have the same problem

Hi guys,

I'm desperate with my Boxer 2.2 hdi, she does not start with a fault in communication with the Injection ECU. The immobilizer stays On, she cranks but no start.

I checked the C Can lines L & H, and the resistance between both is 120ohm.

Can L & H are showing no resistance to battery 12v, and if I measure the Can line to battery...

Hi guys,

Unfortunately one of my locking wheel nuts snapped a year ago so i got a new set from Peugeot last year. Annoyingly, possibly the second time i used the key on one of the wheels, another locking nut broke on me. Does anyone recommend a good set to buy that will fit my Peugeot 508 19 wheel please? maybe tempted to buy just 4 normal bolts...

So my 2011 1.6 hdi Peugeot 3008 had a diesel smell coming into car when driving. On inspection seen a large build up of carbon around the injectors so figured there could be one leaking, also noticed a leak from the egr where it bolts onto to back of the cylinder head. So took off the egr valve and found a missing gasket, replaced that and cleaned...

Hi to all.

When i turn on side lights de horn turn on too.

Hi guys, thanks for letting use this forum. I just wanted a little advice if I may. Cut a long story short I had some discs and pads fitted to my Peugeot 508gt 2.2 last year that was very poor performance, handbrake struggling to hold, brake fade was terrible so i replaced them the other day. I took the electronic handbrake off, jacked the car up,...

Hello everyone,i'm the owner of a 508 RXH Hybrid4 and the nightmares never ends whit this car.
while taking of from an intersection,like I normally do,the car completly went crazy going into limp mode and giving me the message(Parking brake fault,stop the veicle immediatly). Car is dead and i can't start it in any mode so I take it home whit a...

The old Hdi has been running well until yesterday.

I took it for a spin up the coast 200kms to burn off the cobwebs on the freeway and ran fine. Stopped over night and next day all well (eg no oil stains on the driveway)

Went for a short drive (10 kms) at low speed and stopped at some shops. Came out an saw a wet patch under the car (auto...

Any ideas anyone?
I put Diagbox on my car, 2006 Peugeot 307SW, 2.0HDi 138, as I needed to programme a new key. In doing a faults test it tells me there is no communication with the additive ECU. The car isn't actually showing any faults at present.
The additive is the bag type and I have changed the bag.
Any clues as to how to start diagnosing...

Hi guys,

I have, what is sounding uncomfortably familiar on this forum, EPB issues. I'm not going to go into detail on the fault just yet as there are a lot of other great posts here that I want to work through first, but can somebody tell me please where the parking brake module is located please, like the one pictured here:

Sorry I know...

Where can I find the RPO number on my 207cc?
ServiceBox says it should be on a sticker on the left door but there's no sticker.
There is a sticker in the left door jamb. (see attached)
VIN is VF3**************[VIN obfuscated, can be read by forum staff]

At the weekend I disconnected my battery to route a power cable for a small amplifier. I followed the reset procedure noted on the site but had a horrendous experience when i connected it all back up. Hand brake failure alarm, engine fault warning, service flashing, window shut itself and wouldn't open locking was half working, when I tried to...

Hi all,

VIN: VF3**************[VIN obfuscated, can be read by forum staff]

New guy here desperately looking for a solution to a repeating issue.

Car got into a limp mode. When checking codes via Diagbox noticed two errors in the Hybrid control ECU 1 occurring simultaneously. I've noticed that the ancillary belt tensioner was very wobbly so it got changed together with the belt. Hope was...

Hello, for about 2 years, yes, you read correctly, 2 years... What bothers me is the malfunctioning ESP or Semi-functional. It works until I pass a corner at a minimum speed of 60 km/h until then everything behaves fine and ESP works. Then when I turn off the car and start it again the error is gone and it repeats itself every time I drive. Lexia...

Hi,

I have installed OEM tow bar and electric kit on 208 II from 2021. After installation and connection to the trailer the lights of course didn't work.
I hooked up Lexia to the car, bought a token, used oficial Diagbox, and activated the trailer unit. Yuhuuu, trailer works! (wasn't really able to test the fog light as it was missing on the...

I've recently bought a used Peugeot 2008 GT Line (2020) with a 1.5 diesel engine and ATN8 automatic transmission.
It's equipped with 12 parking sensors, blind spot monitoring, radar under the bumper, lane assistance, and safety brake, along with a camera for signs.
What my car missing is active cruise control, automatic parking, highway drive...

Hi guys.

My expert is.... Causing me hell. She has 205k miles so have to be lenient.

So.
Symptoms of this latest issue.

Doesn't start. Just CLICK.
Bump start backwards down hill.

Drive to next job.
Park on hill forwards. Try. Lazy turn over.

11.98Vdc

Assumed it were the LION battery I fitted from ECP in December.

Changed battery for...

hi all,

not sure if this is the right place but i have just purchased a 2015 3008 and was wondering if there is a way to avoide motorways on the system as i cannot seem to find it? i like having the display in car and would rather not just use my phone for navigation if possible. thanks in advance

Hi All,

I have a Peugeot 308, 2015 model (1.2 Litre Petrol, Manual).
It suddenly stopped working (cranks but won't start).
I called the breakdown support and the AA did some diagnostics and gave the following error codes:

Patrol found the following fault code/s:System : Engine control 1 - 9E4 / Engine management Valeo VD46 Status :P1B40 - Engine...

Hi,
I have the cylinder head of on my 208 (EB2 engine). It started with a new timing belt and then I realised it wasn´t that much more job to change the valve steam seals because the car use about 1 litre oil per 1000 km (thought this maybe would help a bit?).

Then I had to take the top of because I accidently damaged a valve when taking one seal...

Hiya my Peugeot partner combi 20hdi 2004 had a new cambelt fitted after a short while about twenty miles it broke down eventually started to get me home then won't start again had a garage look at it they said the timing belt snapped so they fetched it back i went to start it and it started ran perfectly but when hot it would not start again so...

Hi all,

Apologies for the trivial question but I'd like to replace the spark plugs on a 1997 2.0 Turbo (XU10J2TE) and the layout is slightly different to what I've found online for (presumably later) petrol engines. Instead of a plastic engine cover and a single ignition coil pack for all four plugs, I seem to have individual ignition coils (see...

Hey all,
I've searched and searched and I just can't find the info I need, I'm happy to pay for it if someone has it.
I've got a 2021 plate boxer, I've removed the double passenger and fitted a single and therefore the pretensioner wiring doesn't fit, throwing an airbag fault code.
I'm told I can fit a resistor into the wiring to fool the circuit...

Hello,

I have a 2015 Peugeot Expert 2.0 hdi that has started to idle at about 1250 rpm, but if I press the brake pedal, the revs drop back to normal. Also if I switch the engine off for a minute or 2 it seems to reset itself. Sometimes I can drive for about half an hour before it starts doing it again or sometimes it will only go for 10 minutes...

Just looking to see would it be possible for part number DSF - Shock absorber.

Vin: VF3**************[VIN obfuscated, can be read by forum staff]

Kind regards.

I have an oil leak from the oil cooler/filter housing, car has over 200000 on the clock. So I will replace the gaskets on it.

I'm also replacing the Turbo. As I am getting an intermittent error on the Turbo P2566 and it has to come off anyway to get to the cooler. I think it may be coming to the end of its life.

1.6 partner teepee (BHY) 2018,...

Hi all,
All advise appreciated on this issue. I have a 2012 2.0 hdi 163bhp that when fully warmed up will sit with a high idle of around 1300RPM. This reduces to normal idle (800rpm) when the brake pedal is pressed but goes back to 1300rpm when released. It will also drive at this rpm when the accelerator pedal is not pressed i.e. 50mph in 6th...

Hi

I have a 11 reg Peugeot 207 1.4 Diesel which has 98000 miles on the clock. Recently after filling up, the 'Fuel additive level too low' error appeared.
My question is - Is this something only Peugeot garages can change and reset the ECU or do you know if any other garages are able to do it?
My local Peugeot garage has quoted £250-£300 to...

I bought this car here in the motherland, France (my first Peugeot) about a month ago and have finally sorted the maintenance receipts (I'm the 4th owner, it would seem) and I have a few questions about service intervals and oils. The car has 193k km on it.

1) Peugeot recommends a ridiculous 120K km/10 year interval for a timing belt change. This...

Just carried out a monthly scan of my 2017 3008 1.6 HDI with 90k miles and it had B1811:96 for a fault in diesel fuel additive pump showing as intermittent, which I haven't seen before.

I did have the orange spanner symbol illuminate a few weeks ago but it had disappeared by the next start and it wasn't accompanied by a message relating to low...

Can any one help me. I have looked around the Internet but can't seem to find want I am looking for. I have a Peugeot Partner B9 and looking for a replacement catch for the rear seat, the one that locks into the floor holding the seat down. I can't seem to find a replacement or a part number can anybody help.

Morning all,

Struggling to find much regarding the specific problem I am having, and as I'm now running out of things to check, I thought it was time to ask here.

My 1.9 XUD n/a engine in my N reg 306 has refused to start via the key for some time now. I left it stored for a while over winter after discovering this due to a lack of time more...

Hi All.

I have had my 2017 308 GT Line 2.0 blue HDI in at my local Peugeot dealer.

I had pluming white steam consistent with an AdBlue injector fault.

Peugeot put it on the computer and diagnosed a failed AdBlue injector and this was replaced. This in turn had shown up a blocked DPF. I have previously had no issues with the DPF (67,000 miles),...

Hello, I own a Peugeot 308 GTI from 2018 with the 1.6l 193 kw. Yesterday the engine light and the service light came on the car also lost power. This afternoon I went to my local mechanic and the fault code P0235 popped up. This has something to do with the turbo pressure sensor. Did anyone had the same issue or can you help me to locate the...

My wife's 207 is running lovely with the exception of a very random burning smell that is really strong and comes and goes.

It smells like a burning clutch but the clutch is not slipping at all and was changed about 40k miles ago with an LUK one. The burning smell seems to have started since my wife drove through some deep flood water at the end...

Guys

Got a car from Copart, its a P5 Peugeot 308 2022 ex police. However i have couple of questions;

1 - do i need to program a replacement ballast? Spoke to stellenios & you , they reccomend a new ballast to be programmed. But its a sales guy.. i have the headlight

2 - I have some cables and a connector. Can someone please help me to figure...

Hi,

After replacing the original but faulty advance solenoid (coded) with a non coded LUCAS solenoid, I can't start the car.
The new solenoid receives +12V correctly after I start the car with the key.

A diagnostic with PP2000, shows this Default :

ECU Engine / Permanent Fault. Pump Module locked.

Tried to remove F2 fuse : issue is still...

Hi everyone, I am new to the forum and I have a few issues that I would be so grateful for any help with!

After spending hours searching forums and watching videos I am not getting anywhere!

The car is a 2012 207 1.4 vti. It starts and runs although lumpy on idle.

The fault codes I have are:

P1062 variable valve lift system position regulation...

After some advice if possible.

Trying to recalibrate the steering angle sensor on a Peugeot 5008 2012. I'm getting the following codes. I have made sure the wheels are dead ahead. But it keeps failing and illuminating the ESP light. Does it sound like the Angle sensor/ Clock spring I purchased is faulty or could it just need reinstalling? Thanks...