French Car Forum

Hello from Sweden

Our friends work car started to run on 3 cylinders and was producing a lot of smoke.
Fault code on cylinder 3, missfire.
BUT.
What cylinder is 1?
And Id be very thankfull if someome could tell me what ECU it has and what type of injectors.
VIN:
VF3**************[VIN obfuscated, can be read by forum staff]

I have SnapOn and Autocom. Do not have Peugeot specific OBD - only...

I am considering buying 508 with 1.6 Blue HDI engine. Year 2016, around 50 k miles, serviced regularly. There are horror stories about injector, cambelt and turbo all over internet. I wonder if I should pass, or go for it, as car looks good and according to internet, drives really well. I would appreciate more reading on the topic.
So far I found...

Hi
I tried to slove this problem for a while now, with no success in either finding solution online or fixing it myself.
I bought this car with 250k km on the clock
It now has 260k km
I serviced the car when I bought it at 250k (all filters + Total oil) and now recently at 260k (air filter, oil filter, cabin filter + Total oil)
So here is where my...

I have got a 2007 Peugeot 207 SW and some low life has smashed my driver side rear door window, i have went to a scrap yard today and found a 2013 207 SW and the man is willing to give me the back window for cheaper than anything on the internet but i was just wondering before i buy it do the window sizes differ in size from the 2007 model to the...

Hi, as the title suggest, can anyone let me know how to remove the rear spring out of the electrically controlled damper? Please see photo. Thanks.

Hi,

I am wondering if any one have replaced the 407's rear hub bearing only: What I mean is pressing the old bearing out of the wheel flange and mounting a new one in. It seems that Peugeot have only the flange, bearing, nut, and cover as an assembly to sell to the public. I believe the bearing assembly is made by SNR. If anyone have only pressed...

I've been forced to take the gearbox off, due to a slipping clutch (new clutch fitted less than a year ago). Exterior of the bell housing is wet with oil so looks like a seal has gone. The preparation is all done, and what a job that was! Everything is sitting on jacks at the moment. I am looking for a bolting diagram for the bell-house to engine...

Hi! Got this message on my dashboard . My van has done about 72,000 miles but still under warranty. Booked with the dealer on 1/3/2021. Is this serious problem? Can I use my van for 2 weeks or will it lead to more serious problems?. Its Peugeot Expert 1.6 Blue Hdi 115HP, 2018 year.
Thanks in advance.

I just bought a 2007 Peugeot 407 1.6 HDi with 160.000km as my first car. I love how the car looks, how it drives and how comfortable it is and so I´d like to keep it running well. It has a couple of problems and I wanted to ask if any of them need urgent care.

1. EGR Valve stuck open, code P1462 (I took it to a mechanic before buying it and he...

G'evening all

In the days when I had a series of Citroens I frequented this site a lot and then I went to the dark side, Toyota and Lexus Hybrids, my tools have grown rusty and scattered and the brain equally atrophied, Now I have discovered the Peugeot 508 SW RXH I wonder if before I do something silly does anybody have experience of these? what...

Hi does anyone know where the cooling fan relay is located on a Peugeot 5008 2010 please

Hey guys thank you for welcoming me here. My pug 307 1.6v 2007 auto has now reached 106k miles and Ive had the fluid changed, what was put in was Dexron 6 (I know the recommended is Esso or Mobil LT71141). But I have found contrasting threads on here. Some have tried Dexron 3 before and it lasted. Just want to ask, anyone had any experience with...

Hi guys. Have an issue with a 307SW that is doing my head in!

Started out as sidelight not working properly when the indicator or brake light is on, L/H rear light unit. Took the bulb unit out and as suspected the earth pin terminal is a bit burnt, but still serviceable, and after cleaning the contacts I have good continuity between the earth...

A post on the Peugeot board I replied to yesterday has gone missing?
No trace of the original post anymore?

Hello Good people,

I was wondering could someone help me out here, clutch in my 2010 Peugeot 3008 died yesterday...

I was quoted that the new clutch kit will cost me 735 euro and an additional 200 for the work.

I spend some time online and I found Clutch kits that are much much cheaper than what shop quoted me. I managed to narrow down my...

My car is a Peugeot 306, 1.6, gasoline, year 2000.
My car doesn't start and after checking everyting else we came to a conclussion it's something related with my ECU.

I remember I had problems with my battery a few months ago so apparently that could damage the ECU.
I already located my ECU, the problem is that I can't change that to a new one or...

Morning all,
I was having trouble with black smoke and accompanying knock on my 1.9td engine (2002).
I managed to to turn the injector pump a millimetre or two (after a struggle with the bottom of the three fixing bolts!)
This has cured the black smoke problem .....but it still has a slight knock to it...the engine only has about 24,000 miles on...

Hello Guys!

I am new here and I would like to get some help if possible.
I just bought my new van few weeks ago would love it as my baby but always get some check engine light
The usual codes are: P0113 and P0426, but I got already P0428 and P2084 as well but the last two just only once
P0113 Intake air temp sensor
P0426 Catalyst temp sensor

I...

Hi Guys, new to the site and have seen the wealth of info on here which is great. This is my 3rd attempt at owning a Jiffy food van and I think this one is a keeper as its in great condition for it's year 2007/57 2.0 HDI MK1. It has all the equipment fitted to run a food round and l would like to be up and running come Easter with current...

Where in the world can I get a body height sensor that is below £200 for my 2010 boxer?
Found the part number
Continental 1351042080

Hi all, just wondering if one of the electronics gurus could help with a question that's arisen.

When replacing an ECU set it's usual to try and get the matching part number, but I believe that some differences are OK.

Is there any easy way to check if our ECU kit (complete with BSI/BSM and keys etc) with ECU p/n 9644157380 is a viable swap for...

Following on from my minor inccident with my 807 coil springs, i thought i would go ahead and change both front wishbones, a reasonably safe job compared to nasty coil springs.
£197 + vat each from peugeot so thats a no go for me. I started doing an online search for cheaper options, and WOW such a large price variation £70 to £300 a pair.
I'm...

Advice please on changing the ECU and BSI modules on 1.4 petrol 207 2008.
Original ECU/BSI aren't communicating to fault code reader anymore.
Thinking of cutting my losses and changing ECU/BSI and key as a set.
Current ECU is a Valeo unit.
Question is....can I install a replacement Valeo second hand ECU, BSI and key (of a similar vintage) as set...

Hi All,

Having some issues diagnosing a fault with a Partner van and would value some additional thoughts / experience.

The van doesn't start, the dash lights up when the ignition is turned on, but doesn't crank when the key is turned to the start position, the relays in under the dash click, starter, battery and all earths are fine.

A scan...

Hi all a timely WARNING in this extremly cold weather.
I hav'nt been on here for a long time about my 807, touch wood it has been reliable so no complaints really.
Cold weather seems to bring about coil spring failure, well my O/S spring broke (recent break as the metal was still very clean and very little rust) right at the bottom about first 5...

Just fitted a forge dump valve to my 207 gti, it is an atmospheric valve so should make a sound when coming off the gas but doesn’t.
I do have the dreaded depollution system faulty message occasionally but when I reset everything the turbo is working but still no sound from the valve.
Does anyone know if the depollution system thing could be...

Hi, my wife s 306 meridian, the accelerator keeps revving after my wife takes her foot of the pedal, it seems to be sticking , somewhere, any ideas anyone, cheers Terry.

Hi guys. I have a '08 Peugeot 207cc and I am getting a misfire on one cylinder, EML and anti-pollution warnings and the car keeps going into limp mode. I have recently had a new timing chain, injectors, plugs and coils fitted along with a repaired ECU but the problem is still there. The garage cannot figure out what the problem is. I have been...

I've been getting this annoying message everytime i start the 607 about automatic headlight adjustment. I've pull the codes and tried everything i could think off. The sensor is working i've used an multimeter and between pins is changes ohms when i move the arm, check every cable i could see. With peugeot planet i can see it is not registering...

Can someone remind me how to reset the average mpg display to zero please?

I've done it before, just can't remember now how I did it, and the handbook index is very sparse.

The car is a 2007 Peugeot 207CC VTi petrol automatic engine EP6/5FW. In addition to variable valve timing on both camshafts it has variable valve lift on the intake cam. It suffered a descended valve seat on no. 1 exhaust valve (gearbox end), which my engine reconditioner is having a look at. Luckily it didn't fall out completely, although it...

I'm trying to fit cruise control to a 2007 1.4 16v KFU engine non vvt..

I can access the engine ecu with diagbox.. Pp2000 won't access it.. I've switched cruise on in the bsi but when I change the engine ecu to cruise present it won't program and says programming failed. The clutch switch is present. Am I missing something or will it not do it....

Hi all I have a 207cc and when the roof is operated it folds into the boot and then stops and then says roof fault and unable to move it in any direction unless i shut it manually .The boot lid stays up and does not close ontop of the roof nor does the parcel tray cover come out .I have attatched some pics of data reading from p planet third pic...

i have the 308 1.6 s hdi in diesel 2009 , turbo seems to be long time kicking in or it is loeseing power as i and changing gear up hill
feels like the car is strugeling for power .
took a look under the bonet today and seen that there was oil on the top of the actuator and some oil coming from the bottom or underneath of it so at a loss here can...

Hello everyone,
I have little problem with my Peugeot
Gearbox fault snowflake , S ESP light , for no reason in drive. I stop and turned off car, and after starting again, everything normal. (I have car 2 years and that's happened 2 times.
Gearbox work fine.
Yesterday I went to check gearbox and change oil, and diagnostic shows
- Engine - P0336...

Hello!

I have a Peugeot 206 2002 2.0 petrol engine

Altnernator with 1 big + and 1 connector with 2 smaller cables

The Problem

Alternator dont charge, I have 12v if I mesure the small connector.
No battery warning light and peugeot planet software says temporary error databus to cluster but everything in the cluster works.

Are the alternator...

Hello I’m sort of a newbie here.
I have a 308 HDI and I was looking for the turbo pressure valve.

Basically I have loss of power and a dpf has been changed, injectors done, air mass is ok.

Only thing I could find in the forums is the filter gets clogged in the boost pressure valve.

Now I can’t find the location of this part. What I thought was...

Hello!
I have a 2004 Peugeot 406 with a 2.0 HDi engine with a destroyed body and I found at the auction a Peugeot 406 with 1.8 engine and gas installation from 2003. The problem is that in the latter one has a faulty head gasket. So I have two questions. First: what are the approximate cost of head reconditioning and gasket replacement? Second: is...

Anyone know what the bar circled is please?
I'm getting a creaking from the front n/s of the car when I turn with full lock on, had a look to see if I could see anything loose or worn, couldn't, but saw that was missing, and I can't for the life of me remember what it is :)

Thanks very much

Hello all,
I've put a 'new' 1.9TD engine into my van.
I have an outstanding lead coming from the flywheel sensor and can't for the life of me find out where it plugs in. :oops: :oops: :oops:
It's brown/orange with three pins inside....it's on quite a long cable.
Does anyone have an idea where it goes?
Thanks
Moo

Hi
I have had a new Fap tank fitted,which has been reconfigured i was still showing a fault and engine warning light and engine management light was coming on and off. Warning light was always on.
I went back and got the pipe from the fap tank from the fuel tank replaced also now.
All done today but still showing warning light and the engine...

hi all , can any one tell me or say how i am to remove the long black molding on the front as i am going to be spraying it the same as the car
any info on this will help greatfully

My peugeot 207 1.4 hdi 2011 had fault code P1490 keeps coming up randomly sometimes nothing for weeks and other times 3 or 4 times on a 25 mile run.

I've changed the particle filter fluid under the car my car has a pouch of 1100ml and the scan is just showing short of that.

I have not reset any counters as i am not sure how that is done if...

Hello,

did anyone mount the cover in the attached picture on a 156THP engine? if so, did it work well?

in this cover, the diagfram is replaceable (not like in the original version).

Restoring a forklift that uses a XUD 7 or 9 engine.

I see there are 2 pin and 3 pin variants of the oil level sensor and I understand that it also provides Oil Temp as well.

So which version of this sensor has the temperature ability ?

Hi All,
I have a loved Peugeot 205 1.7 Diesel MkII from 1995 and after sucking in some air through a leak in the fuel filter housing developed a small drip on the fuel injector pump.

Does anyone know if I can just unscrew this bolt on the bottom of the injector pump from where I see the drip coming and replace the seal on it, and would that work...

Hello,

I have a Peugeot 308 2012 e-hdi 112hp, and in the last few weeks - since the temperatures outside dropped, i have a EML showing up on the dash.

I took the car to Peugeot main dealer, it showed p2173 air metering valve, throttle body position too open i think. Since the new part was gonna cost 250 euros at the dealer, i ordered a second...

Hi All

Just fitting a timing belt to a mates 406 estate, I noticed when I started it it doesnt turn over very fast, He says it has always been like that.
The starter doesn't look original and I am just wondering if it is the correct number of teeth on the pinion.

It has 12 teeth and I would like to know what the original one was.
Vin...

Hello all !

Can someone please help me with this issue :
Engine management goes on , service says its P3035 (1 injector faulty ) .
In the meantime the van drive , until 2 days a go the DPF comes on , the van its not making the complete process off DPF regeneration . (Probably because of engine management still on ) .
Service is changing...

Hi just new to this but used my 1.9 D berlingo to jump start a small tractor now my van just keeps blowing the 20amp ecu fuse can anyone advise r help me thanks