French Car Forum

With you. Diagbox won't connect to the seat. How do I turn on the seat heating? The seat mat doesn't heat, but the backrest does. Has anyone had this problem and knows where to look for the problem?

Good morning Everyone,

Please can you help me with my daughters 2014 Peugeot 208 1.2

I changed the lower wishbones yesterday and lost some gearbox oil, not a lot but I would like to drain and refill.

How do I do this?

I think I’ve found the drain, but how do I refill?

Also what oil do I need?

Hello,

I have a problem to get timing belt correctly assembled to my peugeot 308 T9 1.2l 96kw puretech. I have used locking pin, locking parts to camshafts. I started engine, I have a p0011 and p0014. When I record parameters, inlet camshaft has value 9, required 40 and exhaust has -15 required is -15. What has went wrong?

VTT wheel preparing...

9th of June 2025 a thud from 5 down to 3rd no clutch ....bye bye c3 picasso. So many hours of Internet searching and a numb brain and giving up a friend emails me and sends me a link for this little car , so off I went on Wednesday arrived at the garage at 4.30 had a look over the car plugged it into the diagnostic 3 codes ( which later turn out...

About to do the rubber band procedure on my 2011 508. It has the 9HR lump, a DV6C mated to the MCP box.

I took a quote for the parts at the dealers, but wasn't entirely impressed by the pricing. They did advice me though, that the crank pinion should be changed. I'm pretty sure the car has this done at a recall about ten years ago, but it's a 50€...

2009 207cc 1.6thp
Any hints on this one greatly appreciated, as this is currently kicking my arse!!
Little bit of history:
Car had a death rattle on startup, if left to warm up rattle went away. I suspected the hydraulic tensioner on it's way out. But seemed fine once warm, so she drove it locally while I got round to doing it. Next it wouldn't...

I have just rebuilt the engine on my 2019 2.0 Blue Boxer.

When I started the rebuild the engine did run but bottom end was shot.
Sice fitting the engine it wont start, it fires and will run for about 5 seconds then stalls, interstingly whilst it is running the throttle pedal has no effect on the revs.
I am using a Launch 129X diagnostic machine...

Hi dear forum members,

Does anyone have removal procedure for the sunroof on a Peugeot 5008 MK2?

I have rust building up under the paint nearly all the way along the gasket of the sunroof, so I need to get it removed so I can tackle the paint repair.

The procedure might be the same on a 3008 MK2.

If anyone has done anything similiar I would...

I am in the need of upgrading the alternator on my Peugeot 205 (TU3MC 1.4L) in order to have enough current to support two 100W rally lights as well as fans from a 205 diesel. Now I was looking into other cars with TU blocks that mightve come with a larger alternator but so far have not found anything that could easily be put on my engine. The...

Hi guys, ive had the check engine light come on my Peugeot Partner mk3 2019 1.6hdi, Ive had 2 mobile mechanics look at it with no joy, it seems it could be related to the stop start system, which is weird because its never actually worked before, but now i've got this problem, the stop\start has started working.
I am hoping someone has experienced...

OK, my recently bought 2021 Expert Van has a steering wheel that looks like it has been attacked by a rabid dog.
I bought a leather bound wheel from EBay and took van an wheel to my friendly mechanic.
He found the wheel and the van are incompatible. Obvious once pointed out the airbags are different shapes D'oh!
The fitted wheel is 98088708ZD I...

Hi all,

I have a 2010 308 cc 1.6 vti allure, and my driver side window is having issues. It has been broken for 2 years now and i havent been able to move it. At first the window started having issues winding up and down, at one point it only winded an inch up and down, then altogether stopped winding up at all. This of course resulted in the...

Good day everyone i have a Peugeot 508 1.6vti ep6c engine which is after my sanity i recently have this multiple codes, the car does not move at all when I start the car it doesn't rev pass 2000-300rpm and it doesn’t move at all despite flooring the accelerator
These are the codes it is showing
1.P101C Variable Valve Lift Relay Control...

Trying to identify this, it fits in the alloy housing pictured which is above the HP pump on the 1.5HDI where the fuel filter used to be sited..check valve? Been googling all afternoon.. #-o

20260528_114401.jpg 20260528_114401.jpg

Good day everon lately I have been getting oil pressure light on my dashboard I ran a diagnosis and I was hit multiple codes which one f them was oil pump solenoid valve which I tested the resistance with a multimeter and it was reading 20-30ohms which was very high I swapped it with a new one which it resistance was around 12ohms, then I tried to...

i have a 2008 Peugeot expert 2.0 hdi that wont start. code p1351, pre/post heating relay circuit. plugs never supplied and code p1350, pre/post heating relay circuit. open circuit or short circuit to earth. i have replaced the glow plugs, glow plug relay and put a new battery in and still wont start. also there is no power getting to the high...

Hello, could someone please help me get the build sheet/equipment list for a e-3008 VIN: vr3**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff]
This is a vehicle advertised since May 2024, with approximately 10,000 km, for sale at a dealership in Portugal and listed as imported from another country. Any relevant history information that could help before I decide to buy it would be...

I know this is a long drawn out post so TLDR : aircon made weird noise now cycles on and off on its own.

I wonder if anyone can point to what is going on here, I have a 2020 Peugeot Expert 2.0 HDI and at first the air con was absolutely fine, last winter the van started making a kind of hooting noise periodically, I traced it to when the AC was...

Hello does anyone know or has anyone come across this fault on an aisin am6 gearbox. The code comes on after 5 minutes of driving with an s and a snowflake flashing by the gear selection screen

Hi All,

I love driving my Peugeot 207cc (2007 model) with the roof down.
My roof always worked like a charm: no noises, quickly etc.)

Suddenly the following was the case:
I tried to open the roof:
Pressed switch down, windows lowered all four, roof procedure started as normal (boot lid opened, roof folded in).
After my roof was folded in, the...

got this to do, have done one before on an MG ZR so I have an idea, but on the 207 is it a difficult job?

any tips welcome

Hi all once again.
Just had a bit of calamity on my sons 308 1.6hdi (110hp) - so double camshaft with chain between them.
He broke down, AA claimed timing belt. Got it home, timing top cover taken off to check and belt is intact. Rotated engine by hand, put timing pins in Crank pulley and Camshaft pulley and they lined up perfectly (and not...

Hello all,

Is there a particular tow bar harness required for the following car:

2010/11 Peugeot 207 1.6 HDI sport. Does anyone have a link and drawings etc. :?: [-o<

Kind Regards

Jason Clatworthy

Hello, May anyone provide location of Peugeot 508 (2016) 2.0 HDI - Gear Box Filler plug & Drain plug location ?

{Setup: 508 (2016) 2.0 e-HDI Start/Stop {DiagBox 9.68 via VMWare). Using: Best Lexia 3 Diagbox V9.129 Full Chip 921815C Golden Edge Diagnostic Tool V7.83 PP2000 Lexia3 }

Hey everyone,

I have a Peugeot 508 2.2 HDi automatic, and I’m trying to understand an ESP / steering angle sensor issue that started after replacing the steering rack.

Here’s the full situation.

A while ago I replaced:

steering rack
tie rod ends
timing belt
coolant
battery (brand new Bosch battery)
AC system repair
wheel alignment

After the...

So,
I joined up the forum as it appears we've been sold a pup, 2019 Partner 1.5Blue.....Was told that it 'sometimes loses power going up hills...' So far replaced the complete wiper assy, the radio as the touch wasnt working, found there arent any front parking sensors fitted due no doubt to an earlier smash...Just invested in a DIAGBOX/LEXIA and...

I have a 2020 1.5 bluehdi 130 gt line Automatic. It wont start and displayed electronic immobiliser fault . I put new batteries in the key fobs and checked the main car battery. It has now gone into eco mode and just displays the 3 warning symbols for parking brake fault and a beep when pressing stop/start. No other dash lights come on.
Pressing...

Good evening all.

My 2011 mk1 5008 2.0 hdi Automatic (Aisin Transmission ) has a tear in left inner CV joint boot .
I was hoping I could expand a cv boot abd slip it over the tripod but that didn't work ,tripod is press fitted and splines staked to stop it coming off.

My next attempt is to remove the wheel side CV joint and fit the boot from...

The engine fires readily, but stops after a couple of seconds. This is completely repeatable it fires every time and the amount of time it runs for does not vary much. The van was running fine and has been parked for a few weeks. The fuel filter is not blocked - plenty of flow with the outlet pipe off and the low pressure pump running. Fuel...

So the coolant has got transmission fluid in it, and my transmission fluid (AM6) has got coolant in it.

I have drained the transmission and coolant from the car (2008 Peugeot 407 2.0hdi) and removed the heat exchanger from the front of the transmission. I expect at least I will need to replace that and seals?

What would be the best approach to...

2001 Peugeot 406 HDI90 estate.
I had all the windows open yesterday to stop the seats melting (it was 35c) and when I tried to close them again the left rear would not raise on the button. Of course then we had a thunderstorm that appeared out of a clear sky and I had to scramble to cover the open window space. Today I am trying to fix the problem...

Hello everyone,
Maybe i dont know how to search but never found an answer.
PSA seems to have 2 types of piloted manual gearboxes in all the 2000-x cars - either 6 speed with hydraulic actuators (called EGS6 or ETG6 or BVMP6) fitted with 1.6HDI and bigger engines or 5 speed with electric motor operated actuators (BVMP5) fitted to 1.4HDI engines...

Hi everyone, I have a Peugeot Expert 2.0 BlueHDi (2018) that cranks but won't start. I've scanned the car with an Autel tool and found a persistent immobiliser issue.
VIN: VF3**************[VIN obfuscated, can be read by forum staff]

Main Fault: B1808(87) - Immobiliser unlocking fault by the engine control ECU (Status: Present).

Immobiliser Status:

Engine ECU locked: YES

Number of keys...

how does the rad come out of a 308?, I have removed the top two brackets, I can just about pull the rad back but it doesnt seem to want to pull up and out of the way, are there two more brackets to undo at the bottom of it? I thought it just had a couple of pins that go through rubber mounts at the bottom and it should just pull up, I dont want to...

Hi Everyone,
I am new to this forum so pardon my mistakes If I do.
I have a 2014 Peugeot 308 2.0 hdi.
Background: It has been to one of the garages here when it had non-start issue. The garage replaced some fuse box (god know which one) and the car worked for a week and then came back on a flat bed.
I got the starter motor replaced and they still...

Hi I have peugeot rifter 2022 model with 8 speed automatic gearbox, mechanic took it in for gearbox issue, as far as i am aware he did work on valve body, then car goes into P and doesn't not come out from park. hope someone can help.

I've just replaced the front driver-side wheel bearing, hub, lower control arm, anti-sway bar bushing, and sway bar link (both sides). The droning noise that I previously experienced with the old wheel hub is no longer happening, but I've now got a new noise/issue...

When driving the vehicle, any uneven road surface causes the van to make a...

Hello everyone

At the beginning of this year I've bought a Peugeot boxer 2.0 2018 with snapped timing.
I was planing to use it as a campervan base and because I never did anything like this before it seemed to be a good idea, as I was hoping I'll get away with only the rocker arms, camshafts and tapets. It was cheap and straight body.
It wasn't...

I'm hoping this might ring a bell with someone. The vehicle is seemingly in good health, no fault codes, runs ok, clean exhaust under start up and usual driving. That is until the van starts an active regen at which point great clouds of billowing white smoke are emitted from the exhaust during acceleration. Once you get up to a steady speed on...

I have read that my car can have fuel filter either by the side of the tank or in the in-tank fuel pump assembly.
I tried looking on the side of the tank but cant see any filter.

Any body know the location and know if there ant service schedule on these?

The start of the story is that i have issues with the car that suggests bad low pressure...

Tengo un peugeot 407 v6
No tiene comunicación la ecu con el Bsi
Codigo f015
Que puede ser? O cual es el pin de cable q debo revisar

Hi all,
Apologies in advance if this has been already discussed.
It is Peugeot 3008 2019 2.0l bluehdi 130kW.
I had warning message on the dashboard engine fault together with adblue light. On Diagbox I can se 3 faults- P208E 71, P20A2 21, P20E8 21.
1st one refers to jammed injector ( see attached pictures) and the other 2 to pressure of the...

Hi
I have a PEUGEOT 2017 Expert III (V) 2.0 BlueHDi 122hk
3 months ago the engine indicator light up and the car went in limp mode. I reset the fault codes and i could drive again. The fault repeated and now it comes every day when i start the car in the morning when its cold the fault code appears after 10.20 seconds. As soon its warm i can drive...

Hello all, this is my first time on here also a new driver so if what I say about my car doesn’t make sense bear with me. Basically my Peugeot 207 2012 would not start you turn the key no response, all fuses and battery have been checked nothing wrong with them. There is no power even to the obd port so I can’t use a scanner. The only things that...

Hi all, my trusty 406 (HDi 90) has had a coolant leak for several years now. I love the car and it's taken me and my family everywhere, so I want to get this addressed.

I've identified the source of the leak at the thermostat housing. The housing itself looks fine (from the angle I've looked at) and the leak seems to be coming from where a pipe...

Surfed all over the internet, contacted TomTom, Peugeot dealers in my city and all over. Nobody can give me information. Why there are not new maps update for NAC wave 2 (for 308SW T9 Allure from 2017)? Last update was in Dec 2024.
Anibody here do you know something about this?

Hi all -

I've got a 2017 Peugeot Boxer with the 2.0 Euro 6 engine - new to me, that I purchased as a non-runner and had a rebuilt engine fitted. It's now running, but has a bit of 'hesitation' when accelerating - most notably around 1800-2000rpm, and also gives off black smoke from the exhaust when accelerating or under load.

I've checked/done...

Hi, new to the forum and in desperate need for advice/help..

I have a Peugeot 207 with the AL4 automatic gearbox. It's triggering a 'Gearbox Fault' with a thud during motorway deceleration. The local garage stuck some diagnostics on it and it showed a solonoid fault. A gearbox oil change was done which helped, but the fault remains - even though...

is it possible to disable stop start fully

Peugeot 2019 3008 GT p84 1.6 THP 164 EP6FDTM 6 speed automatic girpox
The car was involved in an accident on the front right bumper, and since then these errors have appeared and cannot be erased

UF100

B1225

B1226

B1251

B1245

B1210