CitroJim's AX, C3 Picasso, Cycling and Running Tales

[mickthemaverick]

Yeh, you can't see it but it has a corner misssing that I used on the C5.
Well worth adding the extra layer on the inside by clamping it in place, then staple from the other side and bend ends over to hold the tarp. A coat of glue will strengthen it even more!!

[CitroJim]

Have you got a hot staple gun Jim? I can't remember. If not you could bring it here and we-ll sort it.

No, have never felt the need for one as yet. So I'll take you up on that offer Mick. Thank you

Cambelt will be a piece of cake for you with small hands, Jim! You might need some more heft to get the crank bolt out - but they are not that tight. Supposed to be replaced - decent kits come with a new bolt. No real gotchas on these, unlike the 2.0 HDi with the hidden, different sized, bolt down the back!! It's a bit tricky to rotate the crank and wiggle the locking pin (for holding the crank for bolt undoing / tightening only) in over the exhaust single handedly... I've never managed to get the belt back on over the tensioner, but it's easy enough to fit the belt first, then bolt on the tensioner afterwards.

Thanks Richard, that's good to know and some valuable information Yes, my kit has come with a new crank bolt and I'm sure the old one will give up the fight under the ministrations of my rattle gun

I'm almost looking forward to this job!

On my first C5 I had them splitting and no hot staples back then. I actually 'Wallpapered' the inside of the liners with good old blue tarpaulin and spray on upholstery glue, Copydex I believe I used. Repaired and reinforced at the same time!

That's a good thought Mick... I absolutely hate the smell of Copydex. Makes me feel sick

[mickthemaverick]

Ok The only day I cannot do is tomorrow, so any other day including today is fine Jim. Up to you.

[Huskyxantia]

Fibre glassed a wheel arch liner when I was in my 20s that was fun , messy , but fun . Rubbed down primed and sprayed black. My mates poked fun at me saying it was the newest thing on the car a waste of time because no one sees it . I knew it was there . I was very proud of the whole thing .

[CitroJim]

Ok The only day I cannot do is tomorrow, so any other day including today is fine Jim. Up to you.

I'm busy installing a new cooker for the youngsters today Mick, the long weekend is fully booked and really, there's absolutely no rush and whilst the bathroom is being rebuilt there's no space around here due to big white vans being present!

Yesterday, they completed the plastering, got most of the new floor down and are all good to crack on next week. With any luck I should have a nice new functional bathroom by the weekend and then I'll not need to visit friends and family for a shower

[CitroJim]

The Picasso did me proud yesterday - loaded up to the gunwales with an old cooker and much other random detritus that had accumulated in the youngsters' garage... You'd have been proud Matt

Makes me pleased I did not get rid of said vehicle a few weeks back. She still has her uses

The new cooker is a bit posh. First time I've seen an induction hob in action - it's as quick, or quicker perhaps, than gas. I was impressed!

[MattBLancs]

The Picasso did me proud yesterday - loaded up to the gunwales with an old cooker and much other random detritus that had accumulated in the youngsters' garage... You'd have been proud Matt

Brilliant, it's always nice when you are "getting your money's worth" isn't it!

Makes me pleased I did not get rid of said vehicle a few weeks back. She still has her uses

The new cooker is a bit posh. First time I've seen an induction hob in action - it's as quick, or quicker perhaps, than gas. I was impressed!

Yes, we've got one too, it's great. I find that as the hob doesn't really get hot (only by conducted heat back down from contact with the pan) that the glass top is easy to keep clean. Most spillages just wipe off and an occasional (maybe yearly? Not often at all) a quick run over with a scraper blade takes anything more stubborn off.

[mickthemaverick]

.................... a quick run over with a scraper blade takes anything more stubborn off.

I was married for 23 years and used the scraper blade frequently, but she was still there at the end!