Issue in a hurry Peugeot 3008 hybrid

[trollkarlen]

It is probable (but not certain) that your car doesn't have the extra wiring for the additional seat functionality. This would leave you with a seat that cannot be adjusted.

Thx will check tomorrow how it looks in the wiring loom under the seat.

[trollkarlen]

I have an issue with one of the plate lights I thin its the the wireing harness. The right one only get 2.5v and not 12 volts so its shining but very dim. The other one gets 12v as it should. Are these powered direct by the ecu/bsi or they have a fuse ? Anyone with a wiring diagram for the P84E Peugeot 3008 ?

Any hints is welcome

[trollkarlen]

I got the real codes but my diagbox was too old so it could not decode it 9.68

Could someone assist?

ECU
P105904
P16AB07

EAT8
P140605
P17E049

Parking assistance
U1F0000
B124497
B125192

ADAS
B1004 96
U1F00 00

BSI
B120D 86
B120A ?? Warning collision, permanent

Service module
8D93

Which version of diagbox for at least 2020 models?

The main issue now is the collision detect and lane assist warnings.

Found some info on error codes:
ECU
P1059 04 - Ancillaries battery 2 switch : Fault not clear
P16AB 07 - Ancillary drive belt : Mechanic malfunction(This is set when not changed after a certain distance 6000km?)

EAT8
U1406 05 - CAN Flexray : Internal fault
P17E0 49 - Hybrid automatic gearbox input speed sensor signal : Internal electronics fault

Parking assistance
U1F00 00 - Event not recorded fault
B1244 97 - Rear left lateral parking assistance sensor fault : Obstruction or blocking of operation of the system and / or component
B1251 92 - Front right lateral parking assistance sensor fault : Operation or performance incorrect

ADAS
B1004 96 - Multifunction video camera : Internal fault

U1F00 00 - Fault event not stored in the faults log

BSI
B120A 62 Collision risk alert function fault : Signal coherence fault 6
B120A 68 Collision risk alert function fault : Detection of an impact 7
B120A 86 Collision risk alert function fault : Invalid signal 6

Service module
8D93 - Error in communication between the telematic unit and the independent telematic unit : Not characterised

[trollkarlen]

It is probable (but not certain) that your car doesn't have the extra wiring for the additional seat functionality. This would leave you with a seat that cannot be adjusted.

Thx will check tomorrow how it looks in the wiring loom under the seat.

It looks from the wire diagram that is should work(Will count the cables later), maybe the massage can only be controlled with the button and not with the multidisplay cluster.
Will write back if i do the switch.

[trollkarlen]

Change oil in the rear reduction gearbox hybrid

The filling and draining hole is on the backside in the above image.
Two plugs with flat head and hex/square socket(Will update when i know the size).
They can be accessed trough a hole in the plate underneath the rear axel reduction gearbox.
The top plug is for filling and the bottom is for draining.
The capacity is 0.5L, dont over fill.

The oil:
The Electric Reduction Gear Oil (2) is BOT 448, part: 1656247880, £51.92 (1 Lt).

reduction gear for hybrid vehicles
All countries
1656247880 BOT448 oil CASTROL Spec SAE 75W80 1 litre container
Original "Huile BID BOT 448"

[halfoeu]

Ok, but just for future reference, please direct all parts requests to the official members parts thread here:

Citroen, DS Automobiles and Peugeot Official Part Number Requests

That thread is only for parts requests, not technical queries and ensures that they get prioritised as staff may not pick up requests outside of that thread.



(1) Front Suspension Spring, 1 Purple, + 1 Yellow + 1 Green, part: 9815469280, £148.33

This is correct ?
https://xdelar.se/bildelar/product/KYB/RA1559/