Repairing battery clamps
Moderator: RichardW
- CitroenCrazy
- (Donor 2020)
- Posts: 125
- Joined: 20 Mar 2005, 18:17
- Location: Leicestershire
- My Cars: 2000 Xantia Estate Exclusive, HDi
1999 Xantia Estate Exclusive, HDi,
C6 2.2 Manual
They're the modern ones..... - x 63
Repairing battery clamps
I've just changed this loom on my recently acquired Xantia because part of the battery clamp has been damaged. It's the bit from the positive terminal on the battery to the alternator, starter motor and underbonnet fuses.
They seem prone to this type of failure. On the previous Xantia I bought, both terminals had been broken. Fortunately, I had spares to to replace them properly, but now I have none left
In theory, the lead could be melted off the end and a new terminal cast in place. I just wondered, has anyone has ever enccountered a way of repairing something like this that retains the OEM look ?- CitroJim
- A very naughty boy
- Posts: 49620
- Joined: 30 Apr 2005, 23:33
- Location: Paggers
- My Cars: Bluebell the AX, Polly the C3 Picasso, Pix the Nissan Pixo, Propel the duathlon bike, TCR Pro the road bike and Fuji the TT bike...
- x 6182
- Contact:
Re: Repairing battery clamps
Casting a new one should be very possible...
It should be possible to sand cast one if you have a decent example as a template...
I always used to cast my own lead sea fishing weights when I was a youngster...
Maybe plain lead will not be hard enough... It may need to be a lead alloy...
It should be possible to sand cast one if you have a decent example as a template...
I always used to cast my own lead sea fishing weights when I was a youngster...
Maybe plain lead will not be hard enough... It may need to be a lead alloy...
Jim
Runner, cyclist, time triallist, duathlete, Citroen AX fan and the CCC Citroenian 'From A to Z' Columnist...
Runner, cyclist, time triallist, duathlete, Citroen AX fan and the CCC Citroenian 'From A to Z' Columnist...
- white exec
- Moderating Team
- Posts: 7445
- Joined: 21 Dec 2015, 12:46
- Location: Sayalonga, Malaga, Spain
- My Cars: 1996 XM 2.5TD Exclusive hatch RHD
1992 BX19D Millesime hatch LHD
previously 1989 BX19RD, 1998 ZX 1.9D auto, 2001 Xantia 1.8i auto
and lots of Rovers before that: 1935 Ten, 1947 Sixteen, 1960 P5 3-litre, 1966 P6 2000, 1972 P6 2000TC, and 1975 P6B 3500S - x 1752
Re: Repairing battery clamps
The original lead clamps are crimped on to the cable strands, and do lose their grip over time. They're not air-tight, and the strands also oxidise (blacken), and a resistance builds up. Symptom is poor starting, and the clamps getting warm/hot when cranking.
Personally, I'd go for bolt-down brass clamps as replacements. Always possible to paint them grey (or anodize?) for an OE look.
Personally, I'd go for bolt-down brass clamps as replacements. Always possible to paint them grey (or anodize?) for an OE look.
Chris
-
- Donor 2024
- Posts: 464
- Joined: 25 Oct 2019, 07:20
- Location: SW France
- My Cars: C5 Aircross 2021 VR7**************[VIN obfuscated, can be read by forum staff]**************[VIN obfuscated, can be read by forum staff]
Kawasaki ZR1100 1994
C4 Hatchback
Yamaha XVS650A 2001 - x 364
Re: Repairing battery clamps
Thanx to Marc and all the admins & knowledgeable people that make this the best forum on the interweb.