Xsara 2litre HDI crankshaft Pulley
Moderator: RichardW
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Xsara 2litre HDI crankshaft Pulley
Hi have what believe is crankshaft pulley failing starting little noise now clack clacking away like an old diesel!
Did notice while back it looks bit up n down wonky! Did think about other bits like idler,Alternator,Aircon but rev sound isn't quite right as they revolve at different speeds?
Garage/Tyre gaff went to other day to balance wheels said Pulley and Mechanic mate that works on PSA Vehicles said yep when said noise and don't go too far as can take cam belt out!
Now looked at so many pulleys could see them in me sleep!. found ones for Pug 206 diesel £20 yet wanted £36 of xsara but when looked through a list fits either can more!
Are they all the same if162mm extrernal 6 rib?
Did notice while back it looks bit up n down wonky! Did think about other bits like idler,Alternator,Aircon but rev sound isn't quite right as they revolve at different speeds?
Garage/Tyre gaff went to other day to balance wheels said Pulley and Mechanic mate that works on PSA Vehicles said yep when said noise and don't go too far as can take cam belt out!
Now looked at so many pulleys could see them in me sleep!. found ones for Pug 206 diesel £20 yet wanted £36 of xsara but when looked through a list fits either can more!
Are they all the same if162mm extrernal 6 rib?
Re: Xsara 2litre HDI crankshaft Pulley
He's correct that if the pulley completely fails it can take out the timing belt but "don't go too far" is bad advice as it can totally fail without any warning whether you drive half a mile or 500 miles. I would stop using it straight away until it has been replaced.
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
So are they all the same for 2 litre HDI as one item says for x yet others list one for many models from 1.9-2.0-2.2 pug/Citroen/fiatwheeler wrote: ↑31 May 2020, 20:51He's correct that if the pulley completely fails it can take out the timing belt but "don't go too far" is bad advice as it can totally fail without any warning whether you drive half a mile or 500 miles. I would stop using it straight away until it has been replaced.
Re: Xsara 2litre HDI crankshaft Pulley
Better to get a quality one . Dayco, Corteco, Gates etc. Can understand you wanting to cross reference one from Ebay etc but some of them are just cheapos.
Citroen C5 1.6 HDI 110bhp Estate 06 plate
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
One i got is a Febi one(red&white box)looks same as one onit already! but was wondering about rib count this one has 5.Belt looks like 7 but guess have one either side on outside of pulley ribs so makes sense?
They sure don't make it easy esp atmo with things trying to get help/info from them!
Seller is a spares place not in there Bedroom!
Re: Xsara 2litre HDI crankshaft Pulley
Yes, one belt rib hanging over each side of pulley. Febi is decent. Last Febi thing I bought for C5, had Dayco stamped on it, so all good stuff.oscar wrote: ↑05 Jun 2020, 23:10One i got is a Febi one(red&white box)looks same as one onit already! but was wondering about rib count this one has 5.Belt looks like 7 but guess have one either side on outside of pulley ribs so makes sense?
They sure don't make it easy esp atmo with things trying to get help/info from them!
Seller is a spares place not in there Bedroom!
Citroen C5 1.6 HDI 110bhp Estate 06 plate
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
- Huskyxantia
- Donor 2023
- Posts: 2040
- Joined: 30 Jul 2018, 22:11
- Location: Surrey Kent sussex border
- My Cars: Past cars
Xsara Picasso 2019 to 2022 r.i.p
Xantia mk1&2 1.9D & 2.0Hdi
Peugeot 206 sw 1.4hdi
Other models
Skoda fabia,escort van,ford ka,Vauxhall astra g car & estate, Vauxhall corsa b, Suzuki swift
Escorts mk 1,2,3,4,5 fiestas mk 1,2, Sierra diesel mk1 Mondeo mk1 diesel .
Peugeot 207 , 307sw
Now cars
Picasso 2.0Hdi now gone to scrappie
Citroen zx estate 1.9D the cherished one
Peugeot 206cc raised from the dead & saved from the crusher traded up to a 308cc
307sw traded for the 207 .
Wish list.
Peugeot 405 diesel
106 or 206
Mondeo Mk1 diesel once owned 1.8tdi was real nice. - x 423
Re: Xsara 2litre HDI crankshaft Pulley
Time for the impact wrench ?
Different car but 4 years ago my pug had same issue , common fault , paid £25 eBay took a morning todo did the cam belt and water pump as well when you see what these are made of your see why they fail , sold my pug 2/3 years later still running much better but knew the same issue would return in another few years plus I needed a bigger car, good luck with yours , make sure you undo the bolt the correct way, and don't chance the quick turn the engine over trick with long bar wedged on ground.....
Different car but 4 years ago my pug had same issue , common fault , paid £25 eBay took a morning todo did the cam belt and water pump as well when you see what these are made of your see why they fail , sold my pug 2/3 years later still running much better but knew the same issue would return in another few years plus I needed a bigger car, good luck with yours , make sure you undo the bolt the correct way, and don't chance the quick turn the engine over trick with long bar wedged on ground.....
Husky.
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
Huskyxantia wrote: ↑06 Jun 2020, 09:45 Time for the impact wrench ?
Different car but 4 years ago my pug had same issue , common fault , paid £25 eBay took a morning todo did the cam belt and water pump as well when you see what these are made of your see why they fail , sold my pug 2/3 years later still running much better but knew the same issue would return in another few years plus I needed a bigger car, good luck with yours , make sure you undo the bolt the correct way, and don't chance the quick turn the engine over trick with long bar wedged on ground.....
400nm impact wrench! have a large group of people one to use wrench rest to hold car down!
- Huskyxantia
- Donor 2023
- Posts: 2040
- Joined: 30 Jul 2018, 22:11
- Location: Surrey Kent sussex border
- My Cars: Past cars
Xsara Picasso 2019 to 2022 r.i.p
Xantia mk1&2 1.9D & 2.0Hdi
Peugeot 206 sw 1.4hdi
Other models
Skoda fabia,escort van,ford ka,Vauxhall astra g car & estate, Vauxhall corsa b, Suzuki swift
Escorts mk 1,2,3,4,5 fiestas mk 1,2, Sierra diesel mk1 Mondeo mk1 diesel .
Peugeot 207 , 307sw
Now cars
Picasso 2.0Hdi now gone to scrappie
Citroen zx estate 1.9D the cherished one
Peugeot 206cc raised from the dead & saved from the crusher traded up to a 308cc
307sw traded for the 207 .
Wish list.
Peugeot 405 diesel
106 or 206
Mondeo Mk1 diesel once owned 1.8tdi was real nice. - x 423
-
- Donor 2023
- Posts: 13743
- Joined: 01 Apr 2012, 09:47
- Location: Reading
- My Cars: C5 Mk2 VTX+ estate.
- x 3007
Re: Xsara 2litre HDI crankshaft Pulley
James
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
Reading the "BOL" There are two types? Early and late! Early less NM's and DEG.Late which has "Green mark" more NM's & Deg but say's need to lock crank and cam as Cam belt cog is moveable!?
Yet no one/where else mentions that! is that more BS from BOL?
Yet no one/where else mentions that! is that more BS from BOL?
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
Found a deal on a decent Impact wrench that takes my batteries if needed? Mind i guess if using Rattler won't need to lock drive up as best can where as if using long bar will need to pin through disc/in high gear etc?
My impact driver (hex head goes upto around 120nm's?
My impact driver (hex head goes upto around 120nm's?
Re: Xsara 2litre HDI crankshaft Pulley
You are best to put the pin through the flywheel. On a c5 you can get to it from front of car. I made a pin and welded it to a long rod, so I could slip it in. For belt and braces I made a toothed cog to lock the ring gear as well. Do that and nothing will move no matter what force you put on it. I had 5ft scaffy pole and me on end of it.
Citroen C5 1.6 HDI 110bhp Estate 06 plate
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
-
- Posts: 371
- Joined: 29 May 2012, 21:37
- Location: London near that big building with the flashing light!
- My Cars: 2001 Xsara Picasso 2.0 HDi
- x 8
Re: Xsara 2litre HDI crankshaft Pulley
took most of it apart after jacking it up on my old Japan made Yankee 2ton trolley jack.Makita DTW285 impact Wrench made short work of bolt! Lined new one up zapped it on soft setting then torqued it did 50deg odd.lexi wrote: ↑09 Jun 2020, 19:17 You are best to put the pin through the flywheel. On a c5 you can get to it from front of car. I made a pin and welded it to a long rod, so I could slip it in. For belt and braces I made a toothed cog to lock the ring gear as well. Do that and nothing will move no matter what force you put on it. I had 5ft scaffy pole and me on end of it.
got belt back on started it up and........................................silence! pulley wasnt hanging to bits but loose inside was the one that has three slots that looks like has adjustable square bits.
Aircon pulley bearings not great!
Total well more or less as yanked heat shield out from front part as rattling away catching on things
Re: Xsara 2litre HDI crankshaft Pulley
Nice one with the rattle gun! Have that same jack...........25years now.
Citroen C5 1.6 HDI 110bhp Estate 06 plate
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2
French Mistresses gone.
Citroen C5 HDI Mk 1 hatchback
Vel Satis 3.5 v6
ZX 1.9D Est.
ZX 1.9DHatch
Xantia 1.9td est.
Xantia 2.0 hdi Est.
Xantia V6 MK1
Xantia V6 MK 2