Hi
I have removed a faulty fuel injector from my 2014 3008 1.6HDi and now have to replace it with a new one. I have an online manual but unfortunately I cannot find the torque setting for the injector clamp. The injector is a Continental and I found the following post on this site relative to another Peugeot which says it should be 7Nm plus 90 deg. Will it be the same for my car?
viewtopic.php?t=61954
During re assembly is there anything I should be particularly careful about.
Thanks in advance for any info
Graham
Fuel injector replacement Peugeot 3008
Moderator: RichardW
-
OnlineGiveMeABreak
- Forum Admin Team
- Posts: 37331
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5721
Re: Fuel injector replacement Peugeot 3008
Torque settings are specific to each engine Graham and that info I put up was specific to the DV6TED as fitted to that vehicle. But there's no mention in my link of 90° - only 80° for the Bolts (Diesel Injector Fixing Flange).
I may have the info you need, but you'll need to put your VIN up.
I may have the info you need, but you'll need to put your VIN up.
Please Don't PM Me For Technical Help
Marc
Marc
-
- Posts: 20
- Joined: 15 May 2020, 19:16
- Location: Somerset
- My Cars: 2014 Peugeot 3008 1.6HDi
2009 Renault Megane 1.5DCi - x 1
Re: Fuel injector replacement Peugeot 3008
Hi Marc
Thanks for the reply
The VIN is VF3**************[VIN obfuscated, can be read by forum staff]
I have a couple of other questions. I bought a new injector and have measured the thickness of the copper crush washer as 2.1mm thick and 15.00mm in diameter using a caliper. I also removed a second injector for comparison and I have to replace the crush washer for this. I have two new crush washers that I could use with this injector however I have just discovered that one is 2.00mm thick and 15.6mm in diameter and the other is 2.2mm thick and 13.5mm in diameter. Can I use one of these? Or is the 2.1mm thickness and 15mm diameter critical?
The other question is the clamp bolts. They look quite robust (M8) do I need to replace them as I understand they are stretch bolts?
Thanks for your assistance
Graham
Thanks for the reply
The VIN is VF3**************[VIN obfuscated, can be read by forum staff]
I have a couple of other questions. I bought a new injector and have measured the thickness of the copper crush washer as 2.1mm thick and 15.00mm in diameter using a caliper. I also removed a second injector for comparison and I have to replace the crush washer for this. I have two new crush washers that I could use with this injector however I have just discovered that one is 2.00mm thick and 15.6mm in diameter and the other is 2.2mm thick and 13.5mm in diameter. Can I use one of these? Or is the 2.1mm thickness and 15mm diameter critical?
The other question is the clamp bolts. They look quite robust (M8) do I need to replace them as I understand they are stretch bolts?
Thanks for your assistance
Graham
-
OnlineGiveMeABreak
- Forum Admin Team
- Posts: 37331
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5721
Re: Fuel injector replacement Peugeot 3008
Ok, so here are the injection torque settings for your 3008 (DV6C) engine below.
|
Last edited by GiveMeABreak on 17 May 2020, 16:28, edited 1 time in total.
Please Don't PM Me For Technical Help
Marc
Marc
-
- Posts: 20
- Joined: 15 May 2020, 19:16
- Location: Somerset
- My Cars: 2014 Peugeot 3008 1.6HDi
2009 Renault Megane 1.5DCi - x 1
Re: Fuel injector replacement Peugeot 3008
Hi Marc
Thanks for taking the time to look into this.
Am I missing something because I can't see the injector bolt torque. The torque settings above seem to be for the sump and oil pump etc.
All the best
Graham
Thanks for taking the time to look into this.
Am I missing something because I can't see the injector bolt torque. The torque settings above seem to be for the sump and oil pump etc.
All the best
Graham
-
OnlineGiveMeABreak
- Forum Admin Team
- Posts: 37331
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5721
Re: Fuel injector replacement Peugeot 3008
No, it's not you it's me being a numpty - I was doing something else and put up the torque settings for the oil as you say
Leave it with me and I'll sort it - apologies for that....
Edit: I've replaced the image and the Torque data for the Injection system now.
Leave it with me and I'll sort it - apologies for that....
Edit: I've replaced the image and the Torque data for the Injection system now.
Please Don't PM Me For Technical Help
Marc
Marc
-
- Posts: 20
- Joined: 15 May 2020, 19:16
- Location: Somerset
- My Cars: 2014 Peugeot 3008 1.6HDi
2009 Renault Megane 1.5DCi - x 1
Re: Fuel injector replacement Peugeot 3008
Thanks Marc.
This is very useful information.
Have a good week
This is very useful information.
Have a good week