Front wheel bearing

Dedicated to owners of Citroen GS and GSA models.

Moderator: RichardW

macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Front wheel bearing

Post by macplaxton »

Hi,

Had a bash at this on the way home from work yesterday as I've had to start using the GS again and it's grumbly-rumbly.

a) I was on the way home and not heavily tooled-up.
b) I haven't done one before, and hadn't read up on it before hand :oops:

So with that in mind, got the hub nut undone, removed the two bolts holding the top balljoint in place, removed the two bolts holding the bottom balljoint in place, quick strike with a hammer and split the track rod end taper. Wandered over to the bench with the hub assembly. Spent some time picking the rubber seal out. Then discovered the lock ring. Ahh. Gaahh. Decide not to proceed further to prevent immobilising the car and went home in disgust! :x

So I understand I need to buy/make a tool out of a huge socket with a bar slotted into it to engage with the two slots in this ring. I also understand that this ring is 'king tight. I also understand that I might need something tapered to push the hub itself out of the inner race. What is the plastic reducer bush all about in the new bearing? Is it surplus to requirements in this application? Do I need anything fancy to get it all back together.

Your thoughts please.... (calling Malcolm! 8-[ )

Cheers,
Rich
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Re: Front wheel bearing

Post by citronut »

i havent done one for many moons Max,

but a few years back i made a tool for undoing the ring nut on a dersh ( 2cv ),

i used a heavy length of probably 1/4 thick X 2inch wide steel bar, with a length cut from it to weld in a T format onto the face of the longer section,
to be used like a large hefty key which the T blade slots into the two slots in the locking ring,

before you try to undo it mind you drill the two peened points at the edge of the locking ring out,

i use a socket of as close to the outer diameter of the drive flange to drift this out,

hope this helps

regards malcolm
Regards, malcolm.

current ride a BX 1.7 TZD estate
1986 MK1 BX 1.9na D Auto(in Mothman Andy's stable )
layed up roppy 1.9TD XANT estate, now gone to meet her maker
purple and lilac metalic 2CV(VIOLET)registered to her in doors
1972 DS special been layed up aprox 31 years
macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Re: Front wheel bearing

Post by macplaxton »

Thanks Malcolm, that helps a bit.

My understanding is that the two-'orse is similar in design, although has a slightly smaller lockring (or at least smaller slots in the lockring).

How long was the effective length of your special tool handle (including scaffy pole?). How big was your hammer to shock the ring for starters?

Having had a chat with Graeme Seed (who I found out no longer makes tools, but was still very helpful), I've got some plans in my head for something along the lines of the Citroen workshop tool. Rather than make a special one-off for a GS, it might actually get some use if it had the ability to be used on other Citroens of the same design. I don't have any here at the moment and don't intend to, but you never know!
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Re: Front wheel bearing

Post by citronut »

the length of my tool ( oou la la ) is about 15 to 18 inch's and the T blade welded on about half way along the length,

the size/weight of limp hammer depends on the size/holding power of your vice
Regards, malcolm.

current ride a BX 1.7 TZD estate
1986 MK1 BX 1.9na D Auto(in Mothman Andy's stable )
layed up roppy 1.9TD XANT estate, now gone to meet her maker
purple and lilac metalic 2CV(VIOLET)registered to her in doors
1972 DS special been layed up aprox 31 years
macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Re: Front wheel bearing

Post by macplaxton »

Cheers. I'll report back when I've made something.
User avatar
uhn113x
Posts: 1161
Joined: 06 Jan 2004, 22:06
Location: Near Leeds, United Kingdom
My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension.
x 1

Re: Front wheel bearing

Post by uhn113x »

Apologies for hijacking your thread, M, but have you managed to find a standard bearing that will fit?

My OS one (later type on GSA so might be different from the GS) is making a slight noise on right hand corners; I did strip and wash it which made it quieter but think I'll have to replace it maybe next year. There was no apparent corrosion or wear marks on races or balls.

How are you going to get the inside inner race out? One for Malcolm probably!
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Re: Front wheel bearing

Post by macplaxton »

No problem about hijacking the thread Mr Phelan. ;)

I haven't really looked for a standard bearing. I got a NOS one in a Motaquip box that is a SKF. I don't know either if the GSA is different. What may be different is there was some resizing of things in the driveshaft department around 1978.

The inside inner race I assume will come out with the outer. Not really looked that closely at the bearing yet. I have my tool plans in my mind though.
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Re: Front wheel bearing

Post by citronut »

once you have pressed/bashed :yikes: :-D :wink: the drive flange out the inner inner race should almost fall out,

i dont think there is any difference between GS and GSA front bearings,

check ebay link below

http://tinyurl.com/q9qpq35" onclick="window.open(this.href);return false;

Motorquip is part of the PSA group so as good as OE
Regards, malcolm.

current ride a BX 1.7 TZD estate
1986 MK1 BX 1.9na D Auto(in Mothman Andy's stable )
layed up roppy 1.9TD XANT estate, now gone to meet her maker
purple and lilac metalic 2CV(VIOLET)registered to her in doors
1972 DS special been layed up aprox 31 years
macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Re: Front wheel bearing

Post by macplaxton »

citronut wrote:i dont think there is any difference between GS and GSA front bearings,
There is, or at least the kit numbers are different. That is VBK 125. The kit I have is VBK132.
User avatar
uhn113x
Posts: 1161
Joined: 06 Jan 2004, 22:06
Location: Near Leeds, United Kingdom
My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension.
x 1

Re: Front wheel bearing

Post by uhn113x »

citronut wrote:once you have pressed/bashed :yikes: :-D :wink: the drive flange out the inner inner race should almost fall out,
The problem I found with that was that both parts of the bearing come out easily, except the inner race of the inner bearing - the part that is attached to the shaft. That remains there and there's no clearance to get any sort of a puller between the flange on the shaft and the inner race.
i don't think there is any difference between GS and GSA front bearings,

check ebay link below

http://tinyurl.com/q9qpq35" onclick="window.open(this.href);return false;

Motorquip is part of the PSA group so as good as OE
Price is good but I'm a bit wary buying one when he's saying "CITROEN GS 1.3 4/1981 - 1985" !
Also I came across a complete stub axle for an early GSA (1978-ish?) which is different to mine (1982) as the driveshaft is smaller and the hub nut fits the wheel flange is recessed more on the shaft.

'Twould be good if I knew what the exact spec of the bearings are on mine without pulling it to bits.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Re: Front wheel bearing

Post by citronut »

[quote="uhn113x"]
The problem I found with that was that both parts of the bearing come out easily, except the inner race of the inner bearing - the part that is attached to the shaft. That remains there and there's no clearance to get any sort of a puller between the flange on the shaft and the inner race.
[quote]


the bit the shaft goes through is the drive flange not the inner inner race,

as i said above press or drift the drive flange out, then the only thing holding the inner inner race will be the ball bearings
Regards, malcolm.

current ride a BX 1.7 TZD estate
1986 MK1 BX 1.9na D Auto(in Mothman Andy's stable )
layed up roppy 1.9TD XANT estate, now gone to meet her maker
purple and lilac metalic 2CV(VIOLET)registered to her in doors
1972 DS special been layed up aprox 31 years
macplaxton
Posts: 168
Joined: 08 Jun 2011, 18:09
Location: Ireland
My Cars: 1978 GS X2

Re: Front wheel bearing

Post by macplaxton »

uhn113x wrote:Price is good but I'm a bit wary buying one when he's saying "CITROEN GS 1.3 4/1981 - 1985" !
Well it's just the catalogue application reference as a guide.

The one from the GKN / Spidan catalogue is:

GS 70 -> 03/81
GSA 79 -> 03/81
GSA 04/81 -> 86

Now they all have the same rear wheel bearing reference, but the from April 1981, something must have been changed. Having looked up the numbers and trying to get some detail I've found:

Early front wheel bearings are:
OD = 80mm, ID = 40mm, W = 32.5mm

Later front wheel bearings are:
OD = 82mm, ID = 40mm, W = 32.5mm

Now obviously I'm going to add a disclaimer that I don't have the bearings in front of me to make a direct measurement, nor can I confirm for sure the changeover date. I'll throw them GS numbers I have up here later when I've had a look/measure.

Back to the wheel flange that is pressed inside the inner races. Once pressed out, the innermost/inner race should drop out. The outermost/inner race looks from the diagrams to remain in place until the outer race is extracted as the casting holds it in.

EDIT TO ADD SOME PICS:
This is the manual diagram showing a cross-section of the swivel assembly:
Image
GX.41-1.jpg by macplaxton, on Flickr

and here is the manual references highlighted to the 82mm OD bearing
Image
GX.413-3_Reconditioning_a_swivel_hub.jpg by macplaxton, on Flickr

which notes the change to an 82mm OD bearing from R.P. No 1667 (June 1981).

Any help their Mike?
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Re: Front wheel bearing

Post by citronut »

the double outer race'ies can be pressed out with or without the inner raci'ies in place,

on fitting the new bearing you fit it as one lump/unit complete,
then whilst fitting the drive flange into the new bearing, mind you have something ( an old inner race ) or the likes against the new inner inner race inner face, to stop the inner inner race being pushed out as the drive flange goes through both inner race'ies

i know theres lots of inners inner there :shock: :-D :wink:
Regards, malcolm.

current ride a BX 1.7 TZD estate
1986 MK1 BX 1.9na D Auto(in Mothman Andy's stable )
layed up roppy 1.9TD XANT estate, now gone to meet her maker
purple and lilac metalic 2CV(VIOLET)registered to her in doors
1972 DS special been layed up aprox 31 years
User avatar
uhn113x
Posts: 1161
Joined: 06 Jan 2004, 22:06
Location: Near Leeds, United Kingdom
My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension.
x 1

Re: Front wheel bearing

Post by uhn113x »

I was probably looking at it after mid-day and my brain starts to pack up by then!

That's a great help, Mac. I can see what Malcolm means as well.
That said, I think I'll wait till next spring before I swap the bearing as I have quite a few non-car things to do at the moment; there's a pile of car and radio stuff to sort.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
User avatar
CitroenCrazy
(Donor 2020)
Posts: 125
Joined: 20 Mar 2005, 18:17
Location: Leicestershire
My Cars: 2000 Xantia Estate Exclusive, HDi
1999 Xantia Estate Exclusive, HDi,
C6 2.2 Manual
They're the modern ones.....
x 63

Re: Front wheel bearing

Post by CitroenCrazy »

I think I have the proper tool. Where are you based ?

Andrew
Post Reply