​DS 7 Crossback (2019, 2.0 BlueHDi) – "Limit speed to 90 km/h" suspension fault at ignition, DTCs C1174 11 & C1176 11

This is the place for all your Diagnostic related questions or advice.
Myster X
Posts: 1
Joined: Today, 16:08

​DS 7 Crossback (2019, 2.0 BlueHDi) – "Limit speed to 90 km/h" suspension fault at ignition, DTCs C1174 11 & C1176 11

Unread post by Myster X »

​Hi all, on my 2019 DS 7 Crossback 2.0 BlueHDi (~158,900 km) with Active Scan Suspension, switching ignition ON / starting triggers a suspension fault with "limit speed to 90 km/h", and DTCs C1174 11 and C1176 11 (short to ground, linked to the rear dampers) return immediately after clearing. It never happens while driving.
​We already fitted a new AGM battery, telecoded AGM in BSI, reset BECB, and ran calibration in DiagBox, and we haven't opened suspension ECU 7758 yet. Could this be rear wiring/connectors or an internal output driver fault in module 7758? Any pinout or test tips would be appreciated.
User avatar
mickthemaverick
Forum Admin Team
Posts: 21406
Joined: 11 May 2019, 17:56
x 8166

Re: ​DS 7 Crossback (2019, 2.0 BlueHDi) – "Limit speed to 90 km/h" suspension fault at ignition, DTCs C1174 11 & C1176 1

Unread post by mickthemaverick »

I have moved your post here as you have a better chance of assistance :)
I used to be indecisive, now I'm not so sure!
I used to ride on two wheels, but now I need all four!
User avatar
Huskyxantia
(Donor 2025)
Posts: 3954
Joined: 30 Jul 2018, 22:11
x 929

Re: ​DS 7 Crossback (2019, 2.0 BlueHDi) – "Limit speed to 90 km/h" suspension fault at ignition, DTCs C1174 11 & C1176 1

Unread post by Huskyxantia »

Ive run this through Gemini here's the reply

Given that the codes return immediately upon turning the key/ignition ON (prior to driving), this points directly to an electrical circuit check / startup diagnostic test failure executed by ECU 7758 (AMVAR / Active Scan Suspension Module).
​In PSA fault code logic:
​C1174 11: Rear Left Damper Solenoid / Actuator Valve — Circuit short to ground.
​C1176 11: Rear Right Damper Solenoid / Actuator Valve — Circuit short to ground.
​Because both rear damper codes appear simultaneously at ignition turn-on (and never while driving), the issue is almost certainly shared external hardware or power distribution, rather than two individual shock absorber solenoids failing at the exact same moment.
​Key Areas to Investigate & Test
​1. Wiring Harness & Rear Connectors (Most Likely external cause)
​The rear variable damping solenoid valves are exposed to subframe movement, moisture, and road debris.
​Common Ground / Shared Harness: Check the rear subframe harness where the left and right shock absorber harness branches merge. Look for chafing along the rear subframe, control arms, or body heat shields.
​Connector Water Ingress: Unplug both rear shock absorber solenoid connectors. Inspect the pins for green oxidation or water intrusion. A water bridge between the signal pin and shield/chassis ground inside the socket will trigger code 11 instantly on power-up test.
​Resistance Measurement at Damper:
​Unplug the connector at each rear damper.
​Measure resistance across the 2 solenoid pins on the shock absorber itself: typically 2.0 to 5.0 ohms (varies slightly by coil specification, but must not be 0 ohms or open).
​Measure insulation resistance from either solenoid pin to the outer shock absorber metal casing / chassis: must be infinite (Open Circuit). If there is low resistance to the body of the shock, the solenoid internal coil isolation has degraded.
​2. Wiring Checks directly from ECU 7758 Connector
​Before condemning ECU 7758, perform a continuity and short-to-ground test directly at the ECU harness connector with the ignition OFF and module disconnected:
​ECU Location: Variable Damping ECU (7758) is usually located in the luggage compartment (behind the left or right rear side boot trim panel) or under the rear seating area.
​Isolation Test:
​1. Unplug the main harness connector from ECU 7758.
​2. Unplug both rear damper solenoids.
​3. Measure resistance from the rear damper supply/control pins at the ECU harness plug to Chassis Ground. It should show an absolute open circuit (\infty\ \Omega). If you get near 0\ \Omega, the harness is pinched against the body or shorted in a loom flex point.
​4. Measure pin-to-pin resistance between the positive line and ground return line of each damper pair to ensure they aren't shorted to each other.
​3. ECU 7758 Internal Output Driver Fault
​If the external wiring harness and dampers test perfectly to ground, the fault lies inside ECU 7758:
​Shared High-Side / Low-Side Driver IC Failure: Variable damping ECUs use solid-state H-bridge or MOSFET output drivers with internal current-sensing shunt resistors.
​Internal Short: When ignition turns on, the ECU runs a quick low-voltage continuity and pin voltage check. If an internal MOSFET, protective TVS diode, or sense circuit on the rear output channel has failed shorted to the module's ground plane (heat sink/ground pin), the diagnostic MCU detects standard high-side current leakage or zero-voltage drop and immediately flags DTCs C1174 11 and C1176 11.
​Testing ECU internal stage: With the ECU disconnected from the harness, set your multimeter to Diode / Resistance mode and measure between the rear output pins (pinout marked on module board/schematic) and the main ground pin(s) of ECU 7758. Compare the resistance reading of the Front output channel pins vs. the Rear channel pins. A significantly lower resistance reading to ground on the rear pins confirms a blown internal driver IC inside 7758.
Husky. :? Thinking outside of the box is better than sitting in a dark one.
:-D
User avatar
Huskyxantia
(Donor 2025)
Posts: 3954
Joined: 30 Jul 2018, 22:11
x 929

Re: ​DS 7 Crossback (2019, 2.0 BlueHDi) – "Limit speed to 90 km/h" suspension fault at ignition, DTCs C1174 11 & C1176 1

Unread post by Huskyxantia »

More ....

​Diagnostic Summary Table

Expected Reading Fault Condition
Damper Coil Resistance At Rear Shock Solenoid Pins \sim 2.0 - 5.0\ \Omega 0\ \Omega (Internal Solenoid Short)
Solenoid Isolation Solenoid Pin to Shock Body \infty\ \Omega (Open) Low resistance (Shorted to Earth)
Harness Short Test ECU Plug Pin to Body Ground \infty\ \Omega (With dampers unplugged) Low resistance (Pinched wire in subframe)
ECU Output Stage ECU Pins to ECU Ground Pin High resistance / Diode drop (Match front channels) Near 0\ \Omega (Blown driver stage inside 7758)


Hope this might be of some help it made for a good read .. good luck
Husky. :? Thinking outside of the box is better than sitting in a dark one.
:-D