Tales from beyond the grave AKA Dan & Emma's Black Xantia, pug 206HDi, Daniel's 206 Verve 1.4i, GTi180 plus XUD9TE 206!!
-
CitroJim
- A very naughty boy
- Posts: 55172
- Joined: 30 Apr 2005, 23:33
- x 8437
Re: Tales from beyond the grave AKA Dan & Emma's Black Xantia, pug 206HDi, Daniel's 206 Verve 1.4i, GTi180 plus XUD9TE 2
That's superb news Dan 
Jim
A bit of a Citroen AX fan...
A bit of a Citroen AX fan...
-
ekjdm14
- (Donor 2020)
- Posts: 2043
- Joined: 19 Jan 2015, 17:42
- x 270
Re: Tales from beyond the grave AKA Dan & Emma's Black Xantia, pug 206HDi, Daniel's 206 Verve 1.4i, GTi180 plus XUD9TE 2
Well pleased to once again be "back in Black" 
Heater isn't all I remember it being, although I think that's to do with the foam being missing off the blend door & recirc door judging by the click/knock they make on closing rather than the soft thud one normally hears. Other than that all's well so far & nice & comfy once again (spits on Focus seat)
EDIT-: just popped out and swapped the bodged positive battery cable to a better bodge as the body electrics were getting iffy & starter didn't engage 100% Got a nice quick-connect terminal on there now too.
Heater isn't all I remember it being, although I think that's to do with the foam being missing off the blend door & recirc door judging by the click/knock they make on closing rather than the soft thud one normally hears. Other than that all's well so far & nice & comfy once again (spits on Focus seat)
EDIT-: just popped out and swapped the bodged positive battery cable to a better bodge as the body electrics were getting iffy & starter didn't engage 100% Got a nice quick-connect terminal on there now too.
'95 Xantia LX 1.9D-auto, Black, 123k
'97 306 XS 1.6i, Blaze Yellow, 29k
'96 ZX SX 1.9TD, White, 90k
'98 306 1.9D, Cherry Red, 180?k
'05 "Fraud Fuco" Focus stopgap/beater
'12 Mini freebie project
'97 306 XS 1.6i, Blaze Yellow, 29k
'96 ZX SX 1.9TD, White, 90k
'98 306 1.9D, Cherry Red, 180?k
'05 "Fraud Fuco" Focus stopgap/beater
'12 Mini freebie project
-
ekjdm14
- (Donor 2020)
- Posts: 2043
- Joined: 19 Jan 2015, 17:42
- x 270
Re: Tales from beyond the grave AKA Dan & Emma's Black Xantia, pug 206HDi, Daniel's 206 Verve 1.4i, GTi180 plus XUD9TE 2
With Black now pronounced "reliable" once more, I took the opportunity to drop the sump off the Bin-i this afternoon. As predicted the failure was again on #3, although not nearly as bad this time. Bearing hasn't spun this go around, and has basically just eaten the upper shell leaving the lower one with light scarring.
From the wear pattern (very even across the upper shell, probably taken over 10 thou off it though as it's to the copper already but *not quite* as bad close to the parting lines & lower shell same pattern and almost run-able if it hadn't had bits of the upper pick up on it), taken along with the previous failure on that cylinder, I'm hopeful that the rod itself isn't deformed (ovality in the rod bore would tend to pinch worse at the parting line and from what I've read this pattern is almost textbook injector failure symptoms.
Why I didn't hear it "nailing" at idle/free revving (and why it lasted fine on the driveway and died after only a couple of pulls under boost) would be thanks to the ECU having the ability to correct slightly for individual injectors at idle for "smooth running" and rail pressure being lower too... So basically I think with the crank cleaned up and the one shell replaced again (it's having one of the good used ones this time!) it'll need the injectors taken in and tested/refurbed/replaced and maybe will manage to make it more than a mile down the road finally. Be pretty nice as it's got MoT to take us through till end of Feb. so can keep the salt away from Black!
From the wear pattern (very even across the upper shell, probably taken over 10 thou off it though as it's to the copper already but *not quite* as bad close to the parting lines & lower shell same pattern and almost run-able if it hadn't had bits of the upper pick up on it), taken along with the previous failure on that cylinder, I'm hopeful that the rod itself isn't deformed (ovality in the rod bore would tend to pinch worse at the parting line and from what I've read this pattern is almost textbook injector failure symptoms.
Why I didn't hear it "nailing" at idle/free revving (and why it lasted fine on the driveway and died after only a couple of pulls under boost) would be thanks to the ECU having the ability to correct slightly for individual injectors at idle for "smooth running" and rail pressure being lower too... So basically I think with the crank cleaned up and the one shell replaced again (it's having one of the good used ones this time!) it'll need the injectors taken in and tested/refurbed/replaced and maybe will manage to make it more than a mile down the road finally. Be pretty nice as it's got MoT to take us through till end of Feb. so can keep the salt away from Black!
'95 Xantia LX 1.9D-auto, Black, 123k
'97 306 XS 1.6i, Blaze Yellow, 29k
'96 ZX SX 1.9TD, White, 90k
'98 306 1.9D, Cherry Red, 180?k
'05 "Fraud Fuco" Focus stopgap/beater
'12 Mini freebie project
'97 306 XS 1.6i, Blaze Yellow, 29k
'96 ZX SX 1.9TD, White, 90k
'98 306 1.9D, Cherry Red, 180?k
'05 "Fraud Fuco" Focus stopgap/beater
'12 Mini freebie project