pressure relief on system

This is the Forum for all your Citroen Technical Questions, Problems or Advice.
Mark_Lancaster2026
Posts: 18
Joined: 15 May 2026, 16:04
x 1

pressure relief on system

Post by Mark_Lancaster2026 »

Hi
I am sorry if this has been previously covered but I am thinking about servicing the hydraulic system my self and was looking for some advice.
I want the replace the hydraulic pump and my Xantia and the front accumulator. I know that I have to lower the car to remove pressure from the system and then release the pressure plug to release all the pressure.
But I am uncertain where it is , on the pump its self or on the accumulator ?
are there any other pitfalls I should be aware of

thanks in advance
User avatar
mickthemaverick
Forum Admin Team
Posts: 21255
Joined: 11 May 2019, 17:56
x 8134

Re: pressure relief on system

Post by mickthemaverick »

I think you will be able to find the Repair Procedure for that starting at: https://szervizdoksi.hu/citroen/sb.html#/v?ldp=1C2X :)

I got to this page as an example but not using your car's details : https://szervizdoksi.hu/citroen/sb.html ... CT0337&t=2
I used to be indecisive, now I'm not so sure!
I used to ride on two wheels, but now I need all four!
RichardW
Forum Treasurer
Posts: 12600
Joined: 07 Aug 2002, 17:12
x 1491

Re: pressure relief on system

Post by RichardW »

The pressure release screw is on the regulator (that the accumulator is attached to). Only needs to be undone a couple of turns.
Richard W
User avatar
Stickyfinger
(Donor 2016)
Posts: 11838
Joined: 28 Mar 2013, 21:05
x 1996

Re: pressure relief on system

Post by Stickyfinger »

on the pressure accumulator....No need for more than a single turn ( DO NOT REMOVE the Bolt!as there is a spring and ball bearing in there) , low on the front of the engine (13mm ?)
Alasdair
Activa, the Moose Dodger
ekjdm14
(Donor 2020)
Posts: 2000
Joined: 19 Jan 2015, 17:42
x 265

Re: pressure relief on system

Post by ekjdm14 »

Stickyfinger wrote: Yesterday, 12:38 on the pressure accumulator....No need for more than a single turn ( DO NOT REMOVE the Bolt!as there is a spring and ball bearing in there) , low on the front of the engine (13mm ?)
12mm IIRC but the main take-away from the above, which I second, is the DO NOT REMOVE!

Also (for future reference if needed) when planning to replace the rear corner spheres, do remember to "crack" them loose maybe 1/8turn with the suspension on high (body supported for safety) before going through the depressurising. Try and loosen them with the pressure off & you'll just twist off the return lines from the cylinder boot & possibly damage the high pressure line too. Not that I speak from bitter experience or anything... :twisted:
'95 Xantia LX 1.9D-auto, Black, 118k
'97 306 XS 1.6i, Blaze Yellow, 29k
'96 ZX SX 1.9TD, White, 88k
'98 306 1.9D, Cherry Red, 180?k
'05 "Fraud Fuco" Focus stopgap/beater
'12 Mini freebie project
Mark_Lancaster2026
Posts: 18
Joined: 15 May 2026, 16:04
x 1

Re: pressure relief on system

Post by Mark_Lancaster2026 »

mickthemaverick wrote: Yesterday, 12:03 I think you will be able to find the Repair Procedure for that starting at: https://szervizdoksi.hu/citroen/sb.html#/v?ldp=1C2X :)

I got to this page as an example but not using your car's details : https://szervizdoksi.hu/citroen/sb.html ... CT0337&t=2
wow thats the best information I have been able to find with part numbers

thanks for the link