No umph! C5 mk 2 2004 2.0 hdi manual
Moderator: RichardW
No umph! C5 mk 2 2004 2.0 hdi manual
After moving in the shadows of the forum for years, I am stumped.
My C5 is lacking power. Hardly no acceleration in lower gears and really loses speed when going up hill.
If I unplug the connector to the mass air flow sensor, a pollution fault light comes (to be expected!) BUT the car runs perfectly like a rocket.
So, I go away and order a brand new mass air flow sensor.... plug it in, clear the fault with Lexia and.... same as before.. sluggish.. disconnect the connector and it works ok! (But fault light comes on).
I borrowed another Mass air flow sensor from my other. C5, same problem.
Any ideas?
Worth noting that at no time did I ever get a service light come on, only after restarting the car when the MAF is unplugged.
Anyone experience anything similar?
Egr valve was replaced in the last year, also the throttle body.
My C5 is lacking power. Hardly no acceleration in lower gears and really loses speed when going up hill.
If I unplug the connector to the mass air flow sensor, a pollution fault light comes (to be expected!) BUT the car runs perfectly like a rocket.
So, I go away and order a brand new mass air flow sensor.... plug it in, clear the fault with Lexia and.... same as before.. sluggish.. disconnect the connector and it works ok! (But fault light comes on).
I borrowed another Mass air flow sensor from my other. C5, same problem.
Any ideas?
Worth noting that at no time did I ever get a service light come on, only after restarting the car when the MAF is unplugged.
Anyone experience anything similar?
Egr valve was replaced in the last year, also the throttle body.
-
- Donor 2023
- Posts: 2625
- Joined: 24 May 2007, 10:11
- Location: poole dorset uk
- Lexia Available: Yes
- My Cars: C5 X7 2009 2.0 HDI VF7**************[VIN obfuscated, can be read by forum staff]
C4 2010 2.0 HDi Exclusive VF7**************[VIN obfuscated, can be read by forum staff] - x 378
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Going out on a limb as i have a bee in my bonnet about this but if it has a turbo solenoid valve i reckon the filter will not have been changed, may not throw faults up but think back to how long it has been sluggish, just recently or has it been getting slowly worse and only now you are noticing it ?
Happy to be shot down but it was something i overlooked in the Devil Car
Happy to be shot down but it was something i overlooked in the Devil Car
Re: No umph! C5 mk 2 2004 2.0 hdi manual
It happened from one day to the next. No warning,,
I’ll check that filter tomorrow....
Thanks for your reply
I’ll check that filter tomorrow....
Thanks for your reply
- moizeau
- Donor 2024
- Posts: 1590
- Joined: 12 Jan 2015, 16:08
- Location: France 36
- My Cars: 91 BX TZD Estate. Dead but loved
407 HDI 136 auto
C4 2l petrol coupé
2010 Dispatch III HDI 90
AND a 1980 Z1000ST
AND a 1983 GPz1100 inj
AND a 1995 Zephyr 1100
AND a 1980 Z650 (my moped) - x 317
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Have you got, or have access to a Lexia diag tool, if it's happened that quickly it should show something.
Pete
Notice the BX is still top the list but sadly gone
Notice the BX is still top the list but sadly gone
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Filter in turbo solenoid valve cleaned...still the same.
Yes..have Lexia..no faults shown..
Frustrating!
Yes..have Lexia..no faults shown..
Frustrating!
-
Online
- (Donor 2020)
- Posts: 7221
- Joined: 08 Jun 2011, 18:04
- Location: GL15***
- My Cars: 2006 C5 2.0 Litre HDI VTR Automatic Estate.(now sold on)
Currently Renault Zoe 2014 ZE - x 2520
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Careful examination of all the vacuum pipes (the thin rubber ones) might be an idea, they crack and the vacuum is lost so no turbo operation. tiniest of cracks is enough to spoil the performance.
I think Marc put up an image before of the offending stuff and where it's located. (Mostly near the bulkhead on the same side as the battery)
I think Marc put up an image before of the offending stuff and where it's located. (Mostly near the bulkhead on the same side as the battery)
Man is, by nature, a lazy beast, he does not need twice encouraging to do nothing.
- Paul-R
- Donor 2023
- Posts: 6946
- Joined: 07 May 2009, 16:24
- Location: Wirral, NW England; Vaucluse 84, France
- Lexia Available: Yes
- My Cars: 2015 1.6 Blue HDi 120 Peugeot 308 Active SW
2013 2.0 HDi 163 C5 Exclusive Tourer
2003 2.0 HDi 110 C5 Exclusive Estate (Gone)
2001 2.0 HDi 90 Xsara Estate (Gone) - x 1381
Re: No umph! C5 mk 2 2004 2.0 hdi manual
It might also be the MAP sensor. This measures the pressure in the manifold and if it misreports a higher pressure than is actually there then the turbo will back off the amount of puff it blows. On my old Mark 1 (the Mark 2 may be different), and standing in front of the car, the MAP is a small cube device screwed to the RH corner of the radiator surround. It's then connected by a hose backwards to the manifold.
As I get older I think a lot about the hereafter - I go into a room and then wonder what I'm here after.
Inside every old person is a young person wondering what the hell happened.
"Trying is the first step towards failure" ~ Homer J Simpson
Inside every old person is a young person wondering what the hell happened.
"Trying is the first step towards failure" ~ Homer J Simpson
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Thanks for the suggestions..
Checked all pipes.. no cracks or breaks and secure tight connections. Checked pipes from inter cooler. All ok.
Running the car with the mass air flow sensor unplugged from the connector causes car to run flawlessly with plenty of power.
So have replaced the sensor and still have a problem. I have even tried another new sensor and still the same..
So,I am running it unplugged but the depollution fault message is flashing.. but car running ok.
Don’t know what to try next...
Checked all pipes.. no cracks or breaks and secure tight connections. Checked pipes from inter cooler. All ok.
Running the car with the mass air flow sensor unplugged from the connector causes car to run flawlessly with plenty of power.
So have replaced the sensor and still have a problem. I have even tried another new sensor and still the same..
So,I am running it unplugged but the depollution fault message is flashing.. but car running ok.
Don’t know what to try next...
- mickthemaverick
- Donor 2024
- Posts: 13669
- Joined: 11 May 2019, 17:56
- Location: Hertford
- My Cars: 70+ former cars (list available) including 11 Citroens, 3 Renaults
Current cars: 2004 Subaru Legacy 2.5 SEn, 1994 Mazda MX3 - x 6066
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Thinking through your symptoms and observations the fact that it runs perfectly with the MAF disconnected and you have tried more than 1 MAF then I would suggest that maybe the MAF to ECU wiring has a problem. When connected any fault detected by the ecu may be from the loom returning a signal which is false and result in a command to reduce power which will not happen if the MAF is disconnected. So maybe the fault is in the MAF wiring thus breaking the fault condition from the return wire. In other words if a feed wire to the MAF has a faulty voltage on it, it may be reflected to the ecu when the MAF is connected. Break that connection and the return path for the faulty voltage is removed so all runs well (PM me your RPO number and I'll have a look at your wiring diagram and see if I can identify a potential culprit.)
I used to be indecisive, now I'm not so sure!
I used to ride on two wheels, but now I need all four!
I used to ride on two wheels, but now I need all four!
- GiveMeABreak
- Forum Admin Team
- Posts: 37433
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5742
Re: No umph! C5 mk 2 2004 2.0 hdi manual
To be honest this will be mostly all guesswork - you really need to get it diagnosed first and check if there are any fault codes. No point in replacing parts without getting to the bottom of it. It is a well-known fact that cheap aftermarket MAFs are more than useless. There are a multitude of fault codes relating to the MAF and I would expect one of these to come up if there was a fault.
If you've checked the obvious including the air hoses for leaks then get it on a Lexia preferably or on an OBD code reader if you don't have access to one (not that these may always be able to read all the ECUs). Of course the engine will appear to run better with the MAF disconnected - for a short while - but not recommended for long as it will cause the engine ECU to try and compensate the fuel mixture and the engine will start running too lean / too rich which will cause damage to other sensors and components. The engine ECU is just guessing the air and fuel mixture as it will go into a backup mode to keep the vehicle running.
If you've checked the obvious including the air hoses for leaks then get it on a Lexia preferably or on an OBD code reader if you don't have access to one (not that these may always be able to read all the ECUs). Of course the engine will appear to run better with the MAF disconnected - for a short while - but not recommended for long as it will cause the engine ECU to try and compensate the fuel mixture and the engine will start running too lean / too rich which will cause damage to other sensors and components. The engine ECU is just guessing the air and fuel mixture as it will go into a backup mode to keep the vehicle running.
Please Don't PM Me For Technical Help
Marc
Marc
- mickthemaverick
- Donor 2024
- Posts: 13669
- Joined: 11 May 2019, 17:56
- Location: Hertford
- My Cars: 70+ former cars (list available) including 11 Citroens, 3 Renaults
Current cars: 2004 Subaru Legacy 2.5 SEn, 1994 Mazda MX3 - x 6066
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Come on Marc!! I know it was late but no faults showing on Lexia!!
I used to be indecisive, now I'm not so sure!
I used to ride on two wheels, but now I need all four!
I used to ride on two wheels, but now I need all four!
- GiveMeABreak
- Forum Admin Team
- Posts: 37433
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5742
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Oh, did I lose the plot again - I did check back for a reference but was probably on another planet at the time!
So not enough of an anomaly to trigger a fault at this stage. Are you getting any rasping noises or roughness when you loose power?
I had a fault with a turbo hose - but a minute leak that was so small it took them ages to locate. This was enough to cause rough engine running, stuttering and real lack of power. A new turbo hose fixed it instantly.
So not enough of an anomaly to trigger a fault at this stage. Are you getting any rasping noises or roughness when you loose power?
I had a fault with a turbo hose - but a minute leak that was so small it took them ages to locate. This was enough to cause rough engine running, stuttering and real lack of power. A new turbo hose fixed it instantly.
Please Don't PM Me For Technical Help
Marc
Marc
- Michel
- (Donor 2022)
- Posts: 2210
- Joined: 29 May 2017, 13:50
- Location: Nothanks
- My Cars: Some cars and a motorbike
- x 660
Re: No umph! C5 mk 2 2004 2.0 hdi manual
GiveMeABreak wrote: ↑16 Jun 2019, 12:50 I had a fault with a turbo hose - but a minute leak that was so small it took them ages to locate. This was enough to cause rough engine running, stuttering and real lack of power. A new turbo hose fixed it instantly.
I'm hoping this is the issue with James Hellrazor's C5 (also a 2004 2.0 HDi). It's been on Lexia countless times and has had all valves and electro valves checked and/or replaced. Not really solved the issue at all - even at a Citroen specialist.
Lexia shows airflow *drops* when giving it the beans. We've cleaned out the intercooler, made no difference. Out of curiosity I squeezed the bottom intercooler hose where it appears under the right (as you look at it) of the block while James revved the engine and there is a hot draught appears directly there, so a new pipe is on order and we will get it on the ramps, fit the new pipe and check all the underside induction pipery as it simply has to be something down there.
-
- Donor 2023
- Posts: 13745
- Joined: 01 Apr 2012, 09:47
- Location: Reading
- My Cars: C5 Mk2 VTX+ estate.
- x 3008
Re: No umph! C5 mk 2 2004 2.0 hdi manual
I have got some brake cleaner, and I intend to soak the intercooler in that. As Michel said, we did give it a clean out, but what did come out was not very liquid (as nothing came out when it was taken off the car), and when we mixed engine degreaser, washing up liquid, Harpic 10X and hot water (and left it for 10 - 15 minutes) what came out was black and gloopy. Repeats (until we ran out of degreaser) had similar results, so, despite getting a load of crap out, there may still be a load in there (setting a bit like tar).
James
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
- GiveMeABreak
- Forum Admin Team
- Posts: 37433
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5742
Re: No umph! C5 mk 2 2004 2.0 hdi manual
Fingers crossed that might be it - mine was on a MK II C5 (DW10BTED4) 138, but it can happen to any diesel.
Please Don't PM Me For Technical Help
Marc
Marc